15" Long x 1-3/8" tall x 5/8" deep. Waterproof identification light bar is designed for trailers wider than 80". Durable polycarbonate lens and housing. Surface mount to trailer. 2-Wire design with female.180 bullets. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to be taking a look at the Optronics Ultra Thin Line LED Identification Light Bar. The Red Thin Line ID light bar is for over 80" applications. It is sonically sealed, so it's got a nice water-proof design to it when it comes to the lens and the housing. It is a two-wire design, so you're going to have your lead wires for power and ground: whites for ground, blacks for power. They're going to have the point 1.80 female molded barrels on the wires, so that allows for an easy connection if you have that type of set-up. If not, those can be cut off and used for hardware applications.
You can just expose the regular wires. When it comes to the housing and lens, we're looking at a polycarbonate construction. It's very strong and durable. It's got a corrosion-resistant design. This is a surface mount installation, so it mounts directly on the surface of what you want to attach this to. You have two mount holes on the unit, one located on each end.
Hardware is not included. This is SAE and Department of Transportation compliant. It's a full LED system. LED's are going to make great replacements for incandescent lights: They last longer, they burn brighter, they're much more efficient. You don't have to worry about replacing bulbs, and you don't have to worry about brittle filaments. Now we're going to take a look at the overall length measurement real quick, measuring from edge to edge.
This is going to give us a measurement of right around 15 inches, and then measuring the width, that's going to give us a measurement of about 7/8". Then the thickness, this is how far it sticks off the mounting surface. A really low-profile design that's going to measure 5/8" thick. The light's going to contain a total of three LEDs. The power draw of 12.8 volts is 0.038 amps, and Optronics puts a lifetime warranty on the LEDs. We're going to go ahead and hook it up to our external power source so that we can see what it looks like with power running to it.
We'll also be able to turn off our overhead lights, so you can see it in a low-light setting. You can see here that the light sends out a nice, clear, consistent signal. Again, it's got three LEDs that fills up the light bar, and the multi-diode design just really helps optimize the light output. That's going to do it for today's look at the Optronics Ultra Thin Line LED Identification Light Bar.
looks great just as described
works fine.
Exactly as advertised
i think it will work fine
Good, solid and well priced
Fast shipping works great
Exact match to the light I was replacing. Thanks
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.