Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replaces the follow jack from your Stromberg Carlson landing gear. Designed for use with models LG-2 and LG-4. Follow leg connects to the lead jack in your landing gear set with a cross shaft (not included).
Features:
Specs:
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi there fifth wheel owners. Today we're going to be taking a look at Stromberg Carlson's line of replacement landing gear legs. We're going to be looking at both the leading as well as the following leg. These are available in either a 33 and a half inch or 29 and a half inch drop. And there is a difference between those and how it's going to fit in your fifth wheel, so stick along with us, and we're going to show you how to take the appropriate measurements to determine which one's best for you. Here on the inside, you can get a better look at our leg here.
And what you're going to be getting is just the leg that you see here. The leg is going to include the black outer sheathing here. It does have the attachment point at the top for our shaft to connect to, but the shaft does not come included with it.Brackets that it attaches to also don't come included. You'll be reusing those as well. Because the main purpose of these replacements is just for if you have a damaged leg, because in most instances, if your leg gets damaged, it's usually because of an accident.
It does happen. You leave your legs down, you hook up your truck to your fifth wheel, and you start to take off, move a little forward, and the next thing you know, your legs are now damaged. Rather than spend a bunch of money replacing the entire system. We can replace just the damaged components. This is the same leg we we're just looking at, and this is where it extends down through our trailer, the bottom of our tube here.
Coming out of our tube, we have the extension here that is operated by our motor, or if you have a manual crank. And it also includes the drop-leg down here.What you don't get is the quick release here. We do have these available here at etrailer. We just reused the customer's old one. And in most cases, your old hardware is going to be able to swap over, so if it didn't get damaged, then you can just go ahead and reuse it.
The foot also does not come included, but you will receive a new pin. This pin can either be used to attach a foot, or if you don't have a quick link, you can use this pin to operate your drop leg. You just have to pull the pin out, the leg will drop down, and then you have to manually re-insert the included pin over here.Over here we've got our lead leg, and this is going to be very similar to your following leg. The difference is the shaft that comes out of it is designed to hook to your motor or your manual crank. You will get a little bit extra hardware with the lead leg, because you'll get the collar and attachments. You can see the new hardware here, where it attaches to both the cross shaft, as well as the collar that holds our motor and motor transmission in place. The 33 and a half inch length legs are going to be a direct replacement for Stromberg Carlson's LG-2 and LG-4 systems. The 29 and a half inch legs are going to be a direct replacement for Stromberg Carlson's LG-1 and LG-3 systems. Now regardless of which one you get, they're going to have a total lift of 34 and 7/8ths of an inch. And that's going to be the amount that comes out plus the drop shaft.Now you may not be aware whether you have a Stromberg Carlson or what model yours is, whether it's an LG-1 or 2. The best way to determine if this leg is going to work with your system is to use some measurements. We're going to go ahead and show you how to take some measurements, because this is not going to work with just the Stromberg Carlsons. It'll work with any system, as long as your measurements line up. So we're going to go ahead and head into the shop and we're going to compare one of the customer's original legs with our new one, and we're also going to show you how the measurements you'll want to take, where you want to take them, and how to use those to purchase the correct leg here on our website.We've got our old jack sitting next to our new jack here. So you can see these are identical, but what you want to check beforehand, and you can do this while this is in here, because you can see where our bolt used to pass through, we want to measure the distance between our tabs. Because these are actually the mounting tabs that hold it in here. It'll rest on the brackets, and those bolts ensure that it's going to stay rested on those brackets. We're going to measure from the outside of our tab to the outside of our tab, and we've got 21 and a half inches here. The most common sizes are going to be 21 and a half inches like we've got here, as well as 19 and a half inches. That's the slightly smaller size, but those are the two most common.The last measurement we need is the total length measurement, and that's going to be from the bottom of our painted surface here, because this is what moves, it actually extends. We want the stationary portion and we want to measure from top to bottom, and we're measuring 33 and a half inches. The two most common sizes are going to be 33 and a half like we have here, and the smaller size, which is typically 29 and a half. More often than not the 29 and a half is going to have that 19 and a half distance, and with our 33 and a half, the length measurements here, most often, you're going to have that 21 and a half for your tabs. Once you've got your measurements taken, you can verify on our website here, when you're looking at the jacks that you are considering purchasing to make sure they're all going to match up with your old one. And that completes our look at Stromberg Carlson's line of replacement landing gear legs..
Average Customer Rating: 4.7 out of 5 stars (33 Customer Reviews)
Replaces the follow jack from your Stromberg Carlson landing gear. Designed for use with models LG-2 and LG-4. Follow leg connects to the lead jack in your landing gear set with a cross shaft (not included).I have a 36ft toy hauler as I was about to park it after a weekend at the dunes I was lowering the Landing gear and nothing motor turned no lift :( called etrailer and they were great they knew everything I needed and had it in stock , here's the best part shipping was very fast!!! , I installed the new replacement legs today and fit like a glove wow I'm back in business !! !!
Works great and reasonably priced. No issues with replacement as it bolted right up.
Works great still- one year later. Easy to install. E trailer was great to work with. Definitely our first place to look for parts.
While this is the correct length for our Carriage Cameo 5th wheel, the expanded outer tubes that secure the landing gear to the RV frame are in the wrong place. No doubt this works fine for most 5th wheels, but the Carriage 5th wheels require a special leg that is readily available directly from the Venture Mfg. See photo of the OEM special leg made for Carriage and this more common unit.
Other than having to grind off some material from the insides of the locator tabs on the sides because they would not fit flush they work good. The people at etrailer are great to work with and the landing gear came in 2 days. Thanks
I purchased "landing jacks" for my 5th wheel trailer and had a great experience dealing with "etrailer.com". Even thought I ordered the incorrect item the first time, "etrailer" was excellent in providing me with return instructions; and refund. Upon ordering the correct items, items provided were correct and I installed them without any issues. I would highly recommend "etrailer.com"
I couldn't have received better service ! Dana was amazing and I always tell my friends about the great service she provided for me. I received emails start to finish from her the only thing Dana could have done more would have been install the landing gear for me ! as far as the product it is very good quality .
We have not installed yet but the customer service and shipping was great!
Excellent service on time delivery
The LG 177201 fit perfect. I removed the top cap and added more lithium grease. Some of the other E trailer down legs are equipped with grease zert fittings. This would have been a nice feature
excellent and exact replacement for my broken landing leg on my 5th wheel
Came on time 2 day delivery you couldn’t ask for much more
Tim thank you
the landing leg LG-177201 is a match for the vm900.
even the gear Rachel was the same. and it came a day early.
great product at a good price.
Made in USA ,great price, will install today and am sure it will operate as expected. David found what I needed and provided fine service.
Order re[placement leg for a landing gear on a 5th wheel. The people at etrailer were very helpful, especially Pat, who took the time to research the part that I needed.
Just what I ordered and they were perfect. Thanks Bill
Very fast delivery. Part fit perfect
There is nothing they could do to make this better experience, including the thoughtful follow up. Thanks to all of you.
Worked well. Easy to install
Perfect fit. Quick delivery
Works great
Exact fit. Seems to operate just fine. Very surprised I received it is a couple days.
Went right in and worked
Good quality and fair price.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
James
9/22/2019
Great