Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Locking, fork-mount rack lets you carry 1 bike on your roof. 9-mm Quick-release skewer secures bike fork to rack. Ratcheting rear-wheel strap adjusts to accommodate different bike lengths. Tool-free installation on most crossbars.
Features:
Specs:
The Inno Fork Lock III fork-mount carrier lets you transport 1 bike on the roof of your vehicle. A 9-mm quick-release skewer secures your bike's front fork, and a ratcheting strap holds the rear tire. The carrier clamps onto most crossbars with no tools required. A locking cover secures your bike to the carrier and the carrier to your crossbars.
The fork block includes a 9-mm quick-release skewer with an oversize handle. To mount your bike, simply open the handle, lower your bike fork into the skewer, tighten the adjuster, and close the handle. The adjuster will spin freely once your skewer is secure to prevent over-tightening.
A v-shaped wheel tray holds tires up to 2-11/16" wide. The rear wheel is secured by a strap that slides along the tray to accommodate bikes of different lengths. The strap ratchets down on both sides of the rear tire to ensure a tight fit.
The rack installs easily with included mounting hardware - no tools required. Just open the front cover and lift the front lever so you can remove the square nut from the mounting bracket.
Place the rack on your crossbar, slide the bolt into the open end of the bracket, and secure it in place with the square nut. Use the 2 hand knobs and the square nut to adjust the bracket to the size of the crossbar, then close the lever to tighten.
The rear mounting bracket secures to your crossbar with 2 bolts and 2 knobs. Simply place the bracket under the crossbar, slide the bolt into the bracket, and tighten with a hand knob.
Depending on the thickness of the crossbar, you may need to use the included spacer or rubber sheets to mount the rear hardware. Additionally, you will need the Inno long bolt kit (INISF725) to mount the rack on crossbars 1-1/8" - 2" thick.
The Inno Fork Lock III has a locking cover that lets you secure your bike to the rack and your rack to the crossbars. The quick-release skewer handle is under the cover when closed and it cannot be opened unless the cover is unlocked. The front mounting hardware is also under the cover when the cover is locked.
Average Customer Rating: 4.6 out of 5 stars (41 Customer Reviews)
Locking, fork-mount rack lets you carry 1 bike on your roof. 9-mm Quick-release skewer secures bike fork to rack. Ratcheting rear-wheel strap adjusts to accommodate different bike lengths. Tool-free installation on most crossbars.
Fast shipping and well packaged product. Ordering was easy with the online guide
second one I bought, very sturdy, well made. Have driven 1000 mike trips with zero trouble. If I had 3 bikes I would buy one more
Have product for about a month now, was very easy to install, looks and works great so far, would recommend it..
Simple to install and fit well on a Rhino Rack which is a bit less expensive than the Rhino version.
Great product that's worked well through rain and snow over the past year. Easy to mount and dismount my road bike, in addition to the hybrid.
May need to WD-40 or silicon spray the lock, as it's getting a tad tight, but perfect beyond that.
Delivery was timely, it fits nicely and securely.
Thank you so much for providing the below information! My experience with etrailer.com has been great so far and I appreciate the follow up.
The crossbars fit perfectly and I will definitely be writing a review. However, I realized when I opened the bike racks that I purchased the wrong rack for my car/bars.
Would you be able to provide me with information on how to return the bike racks
Simple and easy. It fits my channel aero bars perfectly!!
This is an outstanding rail. And is the second one that I have bought. For a matched set. They were great on my BMW roof racks. Outstanding product as always. Thank you
the T-Bolts and Allen nuts are really prone to corrosion. Make sure you unscrew them 2-3 times a year to apply anti-seize and corrosion inhibitor on the threads. Have 3 of these racks and all T-bolts sheared off when I tried to remove them after 1.5 year. Other than that, its a really good bike rack for the price, will buy a 4th one
The NA391 roof bike rack is sleek and stylish looking. It's light and seems to be pretty aerodynamic. At the same time, it appears to be pretty sturdy. Once clamped to my INNO roof rack system, I can grab the track of the roof bike rack and pull back and forth enough to rock the whole car without it moving on the roof rack system. I would give it 5 stars but for what I believe is a design flaw that INNO seems to have overlooked. Due to the curvature of the roof on the Tucson that the Inno rack system is mounted on, the front clamp of the bike rack does not sit flat on the INNO crossbars. The bike rack comes with a spacer to use under the rear clamp to level the rack. But the bolts on the clamp knobs are too short to use the spacer. I don't understand how INNO could miss this design flaw in their own product. Even with just the thin strips of rubber spacers on the bottom of the rack on top of the rear crossbar is almost too much for the bolts on the knobs. INNO needs to look into this flaw and correct it.
I like the bike racks…I ordered two for my INNO roof rack load bars…good quality and reasonably easy to install.
I did not realize etrailer also carried the same type of bike carrier that will slide directly into the T-Slot track, otherwise I would’ve gotten those instead…Oh well, that’s the way it goes sometimes.
This rack is great. Seems strong and fits my Gary Fisher Mullet easily. Easy to set up. Best thing is Etrailers shipping and tracking. Literally shipped the night I ordered it. Etrailer is great and I would have no reservations about ordering from them.
Had to really search for a roof-mounted fork rack for my Envoy with factory roof racks. Thule & Yakima do not make anything compatible withoutbuying their over-priced roof racks. I heard about Inno, and etrailer had the best price. I was still nervous when I received the rack, but install was straight forward and took about 15 mins. I centered the Inno rack on the vehicle because the factory racks are curved vertically. Fast communication & shipping from etrailer!
Easy to install and works great with my Gary Fisher mountain bike. Plenty of clearance for the brake caliper! Used it in combination with my Rola roof rack on my 2013 Hyundai Elantra. Paula was a huge help with both my orders and making sure I got the right product for my vehicle! Excellent customer service!
Product was very easy to install , very sturdy and well thought out rack. Great service form etrailer keep it up, would definitely recomment to my friends. Happy camper here. Cheers!
Great product, easy and quick to setup, very stable. Delivery was on time as promised. I have using this Inno Fork Lock system for about a year now and like it a lot. Many thanks for etrailer.com team to create and manage website! Your videos really helped me to choose the right product.
Keep up a good work and thanks,
Igor G.
7/3/2018
After two years of use I can confirm that that was the right purchase for us. No complains so far. Easy to put it on and take it off. Works for both mountain and road bikes. Steady and tight on the roof rack of my Ford Fusion. I would recommend this product to my friends. Thanks to Etrailer staff for keep doing great job!
Do you have a question about this Roof Bike Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Cullen
5/20/2024
I have transported two bikes on the INNO roof rack system for several thousand miles without any issues and without any damage to the vehicle on which they are mounted. I am very satisfied with the quality and value, but for the issue regarding the racks being unlevel due to what I regard as a design flaw as noted in the original review. Its a little disappointing that as far as I know, the manufacturer has never responded to the issue I raised.