Curt QuickPin No-Latch Trailer Coupler for 2" Ball - 3" Channel - 3,500 lbs

See what our Experts say about this CURT Straight Tongue Trailer Coupler

• Can a Surge Brake Coupler Be Replaced With a Curt No Latch On a Mastercraft Trailer?
  Based on some information I could find I believe you currently have a actuator like the Dexter DX7.5L A-60 Brake Actuator # DX53FR on your Mastercraft trailer. To switch to a Curt QuickPin No-Latch Trailer Coupler # C54UR you will need to ensure your trailer will not exceed 3,500lbs when fully loaded. You will also need to verify with your local laws your trailer is being legally operated as many laws will require trailer brakes if over a certain weight no matter how far you tow. Since...
  view full answer...
• Lock For Curt QuickPin No-Latch Trailer Coupler for 2 Inch Ball
  There are a couple of different ways you can lock the Curt QuickPin No-Latch Trailer Coupler for 2" Ball, either with a standard coupler lock, or you can use a 1/2 inch diameter hitch pin lock, since that is the same size as the pin and clip (though you should always use the pin and clip that come with the coupler when towing and not a lock). So to lock it you can use any of the following options, depending on what you prefer: - etrailer Trailer Coupler Lock for Flat Lip 1-7/8" and 2"...
  view full answer...
• How To Make Boat Trailer Tongue Shorter To Fit In A Garage
  I would be happy to help! Personally I would go with the Fulton Fold-Away Coupler Hinge Kit for 3" x 4" Tongue - Bolt On - Up to 7,000 lbs # FHDPB340301 since you are only adding 12" of pivot length. At that length you will still have the full weight rating of the coupler so it will be plenty strong for your trailer, but will also allow you to make the trailer as short as possible to fit in your garage or any other tight places. While using the Brophy Ball Mount # BM20 and installing...
  view full answer...
• Recommended Hardware For Installing Curt 3" Straight Tongue 2" Ball Coupler
  For your Curt Coupler 25138 which is similar to their Curt QuickPin No-Latch Trailer Coupler # C54UR, they recommend using grade 5, 1/2" bolts and nuts. If you have an open channel on your straight tongue trailer you will need to use 4 bolts and nuts. This hardware is available at a local hardware store.
  view full answer...
• Quick Pin No Latch Coupler That Accepts a 2" Hitch Ball and Bolts To a 3" Wide Trailer Tongue
  Yes, we have the Curt QuickPin No-Latch Trailer Coupler # C54UR that fits a 3" channel and 2" ball. The coupler is rated for a trailer up to 3,500lbs.
  view full answer...
• Will the Curt QuickPin No-Latch Trailer Coupler for 2" Ball Work with 3" Wide Tongue
  The Curt QuickPin No-Latch Trailer Coupler for 2" Ball part # C82CR is designed for a standard 2" wide x 3" tall trailer tongue. That said, it will work with any tongue size so long as it's 2" wide. It will not work with a 3" wide tongue. The correct version for a 3" wide trailer tongue is the Curt QuickPin No-Latch Trailer Coupler for 2" Ball part # C54UR. The height also does not matter for this coupler either.
  view full answer...
• Torque For Curt QuickPin No-Latch Coupler
  Thank you for your purchase from etrailer of the Curt QuickPin No-Latch Trailer Coupler for 2" Ball - 3" Channel - 3,500 lbs # C54UR. The 100 ft lbs is too much, as the directions specify to torque the bolts to 55 ft lbs. When you over torque a bolt there is a chance that it could sever and break so you'll want to re-install the # C54UR with the correct torque.
  view full answer...

Do you have a question about this Straight Tongue Trailer Coupler?