Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs

See what our Experts say about this CURT Trailer Hitch Ball Mount

• Least Expensive Trailer Hitch, Wiring Harness, and Brake Controller for 2009 Lexus RX 350
  I will give you a list of all the most budget-friendly parts for a complete towing set up for your 2009 Lexus RX 350. It sounds like you have a trailer with electric brakes, so you will need a hitch, 7-way, 4-way (which is needed because it plugs into the 7-way), ball mount, 2" hitch ball and brake controller. So here is the list of the most economical parts for you: - Curt Trailer Hitch Receiver # 13530 - Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C55563 -...
  view full answer...
• What Base Plate Do You Recommend for My 2005 Pontiac Vibe?
  For a great quality base plate for your 2005 Pontiac Vibe, I recommend the Blue Ox Base Plate Kit - Removable Arms # BX3224. The Blue Ox plate comes with a custom-fitting that will be able to attach to the front of your vehicle. It also includes a straightforward installation with no welding necessary. If you need a tow bar to go along with the base plate, I recommend the Blue Ox Acclaim Non-Binding Tow Bar - Car Mount - 2" # BX4330. The Acclaim will fit with the Blue Ox Base Plates without...
  view full answer...
• What Ballmount Works w/ a MultiPro Tailgate?
  No, it will not you would have to remove the item # C45056 to drop the tailgate. There's actually only one that will work, which is the B&W Tow & Stow 2-Ball Mount item # BW44FR. It is designed to work with the MultiPro Tailgate on your 2023 GMC Sierra, and has a 2" and 2-5/16" hitch ball. The B&W item # BW44FR offers a maximum towing capacity of 10,000 lbs, maximum tongue weight of 1,000 lbs, and has either 2-1/2" drop or 3-1/2" rise. I included a picture of the B&W Tow & Stow item #...
  view full answer...
  
• Recommended Drop or Rise Tolerance
  Good Question! It is okay to have a little plus or minus you just don't want the tongue pointed too far either way. In your case I would use the 2" since we know it will have the trailer sitting dead level which is optimal. The Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs part # C45056 will be perfect. This helps to ensure that the trailer pushes and pulls flat on the truck rather than pushing up or pulling down when braking.
  view full answer...
• How To Determine How Much Rise Or Drop I Need For A Ball Mount?
  Hey Darrell, thanks for reaching out. The amount of rise or drop for the ball mount will depend on two things. The height of the hitch on your truck, and the height of the coupler on your trailer. We want the trailer to be level when you are towing, or as close to level as possible. What you can do is park your truck on level ground, and measure from the upper inside edge of your hitch receiver to the ground. Then you can, with the trailer leveled, measure from the center of the ball...
  view full answer...
• Will Trailer Hitch Receiver for 2023 Honda CR-V Also Fit Hybrid
  Yes, the trailer hitch receivers for the 2023 Honda CR-V fit the hybrid model as well. There are no differences for the hybrid hitch since all of the available options fit all models. If I were to recommend one it would be the etrailer Trailer Hitch Receiver # e98848. I like the etrailer hitch because of the matte black powder coat finish. This gives it an OEM look and does a better job hiding inevitable dirt and dings. If the finish isn't a big deal to you, I would choose whichever has...
  view full answer...
• Will Curt Trailer Hitch Receiver fir 2023 Honda CR-V Hybrid
  Yes, the Curt # C12169 will fit your 2023 Honda CR-V Hybrid. However, I recommend getting the Class III # C13397 instead. In addition to the higher capacity, you will have more available options when it comes to accessories and ball mounts with the 2" receiver. The # C56370 will work as long as you have the AWD model. If you have the front wheel drive model you will need the # C59236 instead. Since it sounds like you will be towing you also need a ball mount. If you stick with the 1-1/4"...
  view full answer...
• Will etrailer Trailer Hitch Fit 1996 Jeep Cherokee XJ Sport
  Yes it will. The etrailer Trailer Hitch Receiver # e97AR is designed to fit all models of the 1996 Jeep Cherokee, including the Sport. This features a bolt-on installation and comes with a limited lifetime warranty. If you plan on towing and don't already have wiring you can use the Curt Tail Light Converter with 4-Way Flat Trailer Connector # C56175. This connects directly to your vehicle's wiring with the included quick-splice connectors. Once installed you will have a 4-way to power...
  view full answer...
• Recommendations for a Ball Mount with 4 Inch Drop with a 2 Inch Ball Already Installed
  We can't swap out balls that are in a kit but we do have an option for a 2 inch ball mount with a 4 inch drop that comes with a 2 inch ball. It is # C45056 for a Curt rated for 7,500 pounds. Or you could get the ball mount by itself, # C45341, and add a 2 inch ball # A-90.
  view full answer...
• Can Curt Ball Mount Be Flipped Over To Achieve A Raise In Height
  Hi Mike; yes, a Curt ball mount like the # C45056 can be flipped over. This is considered the rise position and will not impact the capacity in any way. I attached a picture below which shows the ball mount in both orientations, both are acceptable. Your ball mount will actually have a rise measurement as shown below which can be used to help determine if it will keep your trailer level.
  view full answer...
• Compatibility Of The etrailer e98848 Hitch On The 2022 Honda CR-V Hybrid
  Yes, the etrailer Trailer Hitch Receiver # e98848 does fit your 2022 Honda CR-V Hybrid. This hitch has a maximum towing capacity of 3,500lbs, and a maximum tongue weight of 525lbs. If you need a ball mount for your 2022 Honda CR-V Hybrid, I recommend the Curt Class III Ball Mount with 2" Ball # C45056. This kit comes with a 2" ball, a hitch pin and clip, and a ball mount with 2"of drop and 4" of rise.
  view full answer...
• Is Trimming of the Fascia Required When Installing a Hitch on a 2022 Honda CR-V
  There unfortunately is not a hitch available for your 2022 Honda CR-V that does not require some trimming of the fascia. But you don't need to fear trimming the fascia to install a hitch. The trimming is going to be minor and will not be visible with the hitch installed. I have included a video of the etrailer Trailer Hitch Receiver # e98848 being installed. At about the 3:50 mark of the video they cover the fascia being trimmed. The etrailer Trailer Hitch Receiver # e98848 is also the...
  view full answer...
• Curt Receiver Hitch and Complete Towing Set Up for 2021 GMC Acadia
  For your 2021 GMC Acadia, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" item # C13293. This receiver hitch has a maximum gross trailer weight of 5,000 lbs and a maximum tongue weight of 750 lbs. This is the highest rated hitch receiver for the 2021 GMC Acadia. This fully welded trailer hitch receiver bolts onto your GMC Acadia's frame with no welding required. The powder coated steel is sturdy and corrosion resistant. I recommend the Curt T-Connector Vehicle...
  view full answer...
  
• Recommended 2" Rise Ball Mount For 2018 Subaru Forester W/ Draw-Tite Trailer Hitch Receiver 76182
  Since your trailer coupler is 1-1/4" higher than the Draw-Tite Trailer Hitch Receiver # 76182 on your 2018 Subaru Forester I recommend going with a 2" rise ball mount like the Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs # C45056 which comes with a 2" hitch ball and hitch pin and clip. Since the rear of your Subaru will likely sag a bit with the trailer connected, adding the extra 3/4" will be better to make the trailer level when it is hitched. I included a...
  view full answer...
• Class III Ball Mount With a 4" Rise and 2" Trailer Hitch Ball
  While the ball on the Curt Class III Ball Mount # C45056 can also be used in a rise position it will only give you 2" of rise. Instead you would want the Curt Ball Mount # C45070, a 2" Ball # 40038 and a Pin and Clip # C21500 for a 4" rise. You will want to check the hitch ball to verify the torque spec but it currently is 250ft-lbs as we are not able to install the ball for you at our facility.
  view full answer...
• Length From Pin Hole to Ball on Curt Class III Ball Mount C45056
  The length from the pin hole to the ball on the # C45056 Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise is approximately 8-1/4". I have attached an image from Curt showing the dimensions as well as a video review for your reference.
  view full answer...
  
• Recommended Ball Mount for Rise and Drop Requirements with 2 Inch Pre-Mounted Hitch Ball
  For your Ford truck needing a 4 inch drop, I recommend the Curt Class III Ball Mount with 2" Ball # C45056. This will come with the pin and clip and pre-torqued hitch ball. For your 3 inch rise with mounted ball, I recommend the Curt Channel Style Adjustable Ball Mount # C45900. This is an adjustable mount that you could use for the rise and drop needed on either vehicle to work well with your trailer. I recommend a locking hitch pin like # e98880 to secure your investment. We don't...
  view full answer...
• Can Curt Class III Ball Mount # C45056 Be Used in Rise Position
  I spoke with my contact at Curt regarding the Curt Class III Ball Mount with 2 Inch Ball # C45056 referenced in your question. He did state that the ball mount can be used in the rise position, which will indeed provide a 2 inch rise. The issue with this particular model is that the hitch ball will come already torqued from the factory. You can actually remove the ball so you can flip it over to use in the rise position. I have attached a short video demonstration on this product that...
  view full answer...
• Difference Between Standard and Fusion 2" Curt Hitch Ball Mounts
  The Curt Class III Ball Mount # C45056 comes with a standard 2" hitch ball that can be removed and used in the drop or rise position with the ball mount while the Curt Fusion Ball Mount # C45154 has the 2" hitch ball welded to the platform so it can only be used in the drop position. The Fusion looks a little cleaner but it does lose that rise position so I recommend going with the standard # C45056 just in case you ever need to remove the hitch ball and reinstall it on the other side...
  view full answer...
• How Much Torque Is Applied to the Curt Class III Ball Mount with 2 Inch Ball
  The Curt Class III Ball Mount with 2" Ball part # C45056 comes pre-torqued to 250 ft. lbs.
  view full answer...
• Recommended Trailer Hitch for a 1994 GMC Yukon
  Since you referenced 3 trailer hitches that fit your son's 1994 GMC Yukon I believe you are referring to the Curt options. The main difference between all 3 options is that each one has different gross towing weight (GTW) and tongue weight (TW) weight ratings: Curt Class III - # C13121 500 lbs TW/5,000 lbs GTW Curt Class III - # C13029 600 lbs TW/6,000 lbs GTW Curt Class IV - # C14029 1,000 lbs TW/10,000 lbs GTW When I looked up the max trailer weight rating for a '94 Yukon it looked...
  view full answer...
• Recommended Ball Mount for a 2021 Chevy Tahoe
  For your 2021 Chevy Tahoe, I recommend the Curt Class III Ball Mount with 2" Ball item # C45056. This ball mount has a 4" drop, a 2" rise and a 7,500 lbs capacity. I have linked a review video below that will go over the functions of this ball mount. I also recommend purchasing the etrailer Hitch Receiver Lock item # e98881. This locking hitch pin will secure your ball mount from theft.
  view full answer...
• Hitch, Brake Controller & Related Towing Items for 2014 Chevrolet Silverado 1500 Long Bed
  We can help you get your 2014 Silverado 1500 long bed ready for towing your trailer. Your owner's manual is the best place to confirm the truck's towing capacity but you can also check with your local dealership using the truck VIN. It sounds like you need a 2-inch ball mount with about 4-inches of drop to allow your hitched trailer to remain level, which is important for good handling. You can use ball mount/ball combo # C45056 or use our ball mount kit # 989900 which has two ball mounts,...
  view full answer...
• Ball Mount & 2 Inch Hitch Ball For 2017 Ford Explorer Towing U-Haul Trailer
  For your 2017 Ford Explorer, you'll need a ball mount with about a 2 inch rise, and there is one available that includes everything you need: - Curt Class III Ball Mount with 2" Ball # C45056 The # C45056 comes with the ball mount that has a 2" rise, the 2" hitch ball, as well as the pin and clip to secure it in your hitch.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?