Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This tool makes it easy to install, remove, and carry your heavy weight distribution head assembly. No need to strain your back or get dirty or oily. It uses leverage to enable better distribution of weight for easy and clean maneuvering.
Features:
Specs:
Note: The HitchGrip cannot fit around a ball neck with a diameter greater than 1-5/16".
Easily Install, Remove, and Carry Your Hitch Head
The HitchGrip is a simple tool that makes it easy to install, remove, and maneuver your weight distribution head assembly. Dealing with an oversized ball mount or heavy weight distribution head can be a real headache. These assemblies can be heavy, awkward to handle, dirty, and genuinely uncooperative. But with the HitchGrip carrying tool, you can do what is needed with your assembly as quickly, cleanly, and painlessly as possible.
The HitchGrip makes it easy to get a good grip on your head assembly. As a result, you won't drop your expensive, heavy equipment, nor will you strain your back trying to awkwardly carry it. It also allows for proper leverage so that you don't have to wiggle and shake the assembly to install or remove it. This saves time and eliminates frustration. And because you don't actually have to touch your head assembly when you use the HitchGrip, you can avoid getting grease and grime onto your hands. This allows you to go from task to task without needing to clean your hands in between.
How to Use the HitchGrip Carrying Tool
First, position the HitchGrip to the side of your hitch ball with the handle pointing toward the rear of your vehicle. Then tilt the tool downward and slide it onto the ball to engage. Make sure that the HitchGrip is centered over the ball mount or hitch head so that the weight will be evenly distributed. Then lift up on the handle of the HitchGrip so that the carbide tips grip the underside of the ball. Once the tool has a good grip on the ball, you can carry and maneuver your ball mount with ease. When you install your ball mount in your hitch receiver, you can also use the HitchGrip to easily line up the hitch pin holes.
Recommended Clearance for Drop Hitches
If your ball mount or head assembly is in the drop position, the HitchGrip may not work on your setup. In order to ensure a good grip and proper leverage, it is recommended that you have no more than 4-1/4" between the top of the hitch head and the top of your trailer hitch receiver. If there isn't enough space between the tool and the top of the hitch head you may not be able to get your hand securely around the handle.
Average Customer Rating: 4.8 out of 5 stars (368 Customer Reviews)
This tool makes it easy to install, remove, and carry your heavy weight distribution head assembly. No need to strain your back or get dirty or oily. It uses leverage to enable better distribution of weight for easy and clean maneuvering.Works great for carrying hitch without getting your hands all dirty or greasy and much easier on the back when lifting. Great customer service by etrailer with updates on shipping order and ease of doing business. Will use them again for needs related to the products they sell.
Works well! Makes carrying my camper trailer hitch so much easier and safer.
Amazing how easy you can now handle the “knuckle” as I call it. Balance is perfect when carrying !
Very handy to carry the ball without having to grab the whole thing. This is really helpful for the weight distribution I have, it's heavy (see photo). The other advantage is if you need to swap out your draw bar/ball and don't feel like, this helps. Thanks to George for the updates!
Dave S.
4/14/2019
Its still great! Helps my back and keeps my hands clean.
This tool really helps with moving the heavy & awkward receiver around . It also helps from getting the ball lubricant on my hands . I would definitely recommend this product .
Chris
12/2/2023
This product is a must ! It’s very useful when installing & removing the receiver around . Keeps the ball grease off your hand too . I highly recommend this product .
Mike L.
12/2/2023
This is in my top 5 tools to ever purchase. This holder makes it so easy to carry that heavy hitch to the truck and use it to insert into the receiver. Absolutely the most valuable tool for my rv. This hitch weighs approximately 80 lbs, with the tool it is much easier to handle and not drop on my foot.
Hitchgrip has made removing and installing my heavy trailer much easier
When I first saw this from an etrailer.com email blast, I couldn't figure it out until I clicked the link and read more about it. When I received the HitchGrip yesterday, I showed it to my wife and now even she feels comfortable picking up the heavy hitch... this is a great new product that I will definitely promote to my many RV trailer friends!
The hitch grip makes removing and instaling my WD hitch a breeze. No more having to grasp a filthy greasy hitch to remove or install. Just grab onto it with this tool and carry it away one handed you dont even have to touch the hitch. Well worth the money.
An excellent tool, solid construction, light weight and nothing cheap ( meaning poor quality) about it. It allows inserting and removing the heavy draw bar with one hand if you can manage the weight, or two hands if not. You never need to touch the draw bar which always seems greasy. Reasonably priced, I bought two and gave one to a fellow camper.
Michael
6/22/2023
Still works as designed, I use it nearly every time I or remove my draw bar. At first I thought it would be easy for the draw bar to slip out of the tool, but once the weight of the bar is on the “jaws”, that is virtually impossible.
This did not fit around what I thought was my standard shank of my 2 5/16 trailer hitch ball and it is well-built. I just can’t use it make sure you measure your shank.
If you have back issues this product gives you more ease & leverage to install your hitch. I personally have found that I have not been using it much because when I am hooking up the trailer I am to lazy to get it out of the storage compartment & just lift the hitch manually and insert it in receiver.
It was a waist of money because I have a four wheel drive truck and hitch has a 7in drop. The HitchGrip does not fit.
I only used the carrier a few times, but it worked well and was a big help to me. I have since sold the camper and the hitch carrier went with it.
This is in the top 5 RV accessories I have ever purchased. I can do one handed hitch movement without getting all grease. It does have the bad habit of sliding past the flats on the ball but we learned that carrying it by the handle directly above the ball took care of that.
It is the best helper to lift a heavy hitch and place it in the receiver. Enables me to align the hitch to the receiver with ease. Also keeps me from having grease on my hands. I would recommend it to anyone who needs a help placing a hitch to the receiver.
Such a simple idea that really works. The Hitch Grip allows one to much more easily maneuver the heavy hitch head into place in the receiver of the tow vehicle. The way it is built, it can be used one-handed to lift the hitch into place (or two hands if needed) and then reversed to help position the hitch shank to line up the holes for the locking pin.
With this in mind, it works best with heavy weight-distribution hitch heads such as the Equal-i-zer hitch or the Fastway E2 hitch or other similar hitches. It helps with ones like the Hensley Cub, but with the articulating joints in the Hensley hitch, it does not work quite so well for lifting as the mechanism wants to move. Still, it is helpful to lift the hitch onto the shank so it can be installed removed from the shank when it needs to be taken off for trailer maintenance.
I went through several months without the Hitch Grip. I bought one but gave it to my daughter when I gave her the Equal-i-zer hitch. I ended up purchasing another one to help with the Hensley Cub. It is a big help when lifting the heavy parts. I recommend it highly.
Stephenh
10/28/2020
Follow-up: My original review is still valid. It is still one of the more useful tools for dealing with heavy hitch heads.
This is about as useful as you'd expect. I don't get grease all over myself, I don't hurt my back because I can balance the load. It is much easier to manipulate my heavy and unwieldy hitch . If you've got back issues - this can help. It did me.
There’s a learning curve to use but it makes it easier to insert hitch. As always very happy with etrailer. Reggie
Works as described. Only problem, for me at least, is getting it safely inside my cargo area of the trailer, as my weight distribution head is substantially larger than most. And maybe 100 pounds.
Does make it cleaner, easier to lift and insert / remove from the hitch.
Etrailers Service and shipping cannot be beat, arrived 3 days earlier than quoted. Excellent!
Roger D.
1/1/2021
At first, I thought that the hitch might wiggle free from the carrier and on my foot! Never happened! Easy to use, and I figured out how to easily put it back inside the cargo door of my Outdoors Rv trailer. No greasy hands, redistributes the weight for a much easier lift and carry. Excellent tool to have.
Works great. It helps me to be able to install my weight distribution hitch easier at my age.
I just got it and have not used it on a trip but have tested it on my hitch-ball assembly. It is well made. The handle is a plastic composite but it is very strong. My only caution would be to MAKE SURE you are properly hooked on the ball, just like they instruct. My hitch-ball assembly must weigh at least 40 lbs and if you are not properly attached to the hitch-ball and drop it on your foot you are taking a trip to the ER. Keep your feet out from under it!
Peter C.
5/19/2018
Same as above. Used it now and it works well but do not hold your hitch ball assembly over your feet!
I got this product to help me lift and carry my weight distribution hitch since I often hitch and unhitch my trailer by myself. As a woman in my 60's being able to handle the hitch without having to "wrap my arms around it" and get grease on my clothes is a really good thing!
Robbie
7/30/2021
Still liking this product even though I havent had very many chances to use it this year!
I haven't tried it yet but i'm looking forward to it later this spring.
It works !
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thomas
7/10/2024
Great !