Sturdy steel ball mount with hollow shank measures 8-1/2" from center of hitch pin hole to center of ball hole. Angle-cut shank slides easily into your hitch. Powder coat finish over a-coat base provides excellent rust protection.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2013 Honda Odyssey, we'll be test-fitting the Draw Tite ball mount with three quarter-inch rise or two-inch drop part number 2923. To begin our test-fit we'll go ahead and get our hitch height. This is measuring from the ground to the inside top edge of our receiver tube. We have a hitch height of two inches. Now we'll go and pick our ball mount and install it in the drop position. We'll just line up the pinhole and then insert our pin and clip.
Our drop position measurement is nine-and-a-half inches. This is measuring from the ground to the ball platform. Make sure when measuring your trailer height you do so when your trailer is level. You want to measure from the ground to the bottom of the coupler. If your measurement matches ours, then this would be a correct fit for you.
Now we'll take our ball mount and switch it to the rise position. We'll just line up the pin hole and then install our pin and clip. Our rise position measurement is 13 inches. If this measurement matches yours, then this would be a good fit for you. That completes our test-fit of the Draw Tite ball mount with three quarter-inch rise or two-inch drop part number 2923 on our 2013 Honda Odyssey..
Average Customer Rating: 4.9 out of 5 stars (760 Customer Reviews)
Sturdy steel ball mount with hollow shank measures 8-1/2" from center of hitch pin hole to center of ball hole. Angle-cut shank slides easily into your hitch. Powder coat finish over a-coat base provides excellent rust protection.arrived quicker than expected. waiting for temps to rise a little higher than 28degrees so I can install new hitch. thanks for awesome service. I work in a body shop and I let my manager know of prices and service. he will definitely be checking you out. 732434
Does what it is supposed to do. 696861
Awesome product easy to install !!! Saved me over $800 by doing it myself as the dealer wanted $1058 for the same bolt on set up... awesome price guys thank you very much.... 518457
Solid, heavy ball mount. 441408
Peter H - 10/20/2018I was just rear ended in my suv. During the accident the Hitch ball mount was bent. As usual I visited the etrailer web site so I could purchase another one. That has to be one of the nicest quickest web site I have been on. Thank you it was extremely easy to find and order. Delivery was very quick. Thanks again. 676916
Purchased a can of BP Blaster penetrating spray the day after I ordered the parts. I sprayed the weld nuts several times while waiting for the parts to arrive and it seemed to help loosen them up. My order arrived on time and I installed the hitch the next morning. I installed the hitch by myself ( I'm 67 years old), and while I admit that an extra set of hands would have been very helpful, the install was easier than I anticipated. I had all the parts I needed, the instructions were easy to follow and the online video was very helpful. I purchased the hitch in order to tow a trailer with a ton of wood pellets, instead of getting 1/2 a ton at a time (the capacity of my truck). Hopefully these products will solve my problem, only time will tell. 392664
Just what you need for small drop 201735
Richard W - 06/07/2016Awesome great fast delivery! 571234
Product as advertised. Wished I'd paid more attention to what was included and not included. Seller web site did a good job indicating other suggestions on what would go with what you were viewing. So much so, I became dependent on it, and over looked the fact that the pin to hold the ball mount was not included in either the receiver or ball mount. I overlooked this and had to go out and buy this somewhere else. Other than that ordering was easy, and I received everything in a timely manner. It's worth noting that their tracking was dead on as well. It's nice tracking the progress of a package you are waiting for so you can plan your installation. And again, they do a nice job of following up letting you know they received, shipped the order and a link to follow it in transit. 147675
Fastest delivery I have ever had. Ordered Wednesday at 5PM, arrived Thursday at 3PM. I'm only a couple hundred miles from Wentzville, but still, excellent. The hitch receiver (2008 Pilot) installed quickly and easily. No need to remove spare or lower muffler. I supported the left end on a large cooler and quickly maneuvered the right side above the tail pipes. The mounting holes were right on target. I had to tap mine to remove rust, but that's easy as well. The wiring harness was also a snapto install. Simple to plug into existing fitting and the wiring box tucked away nicely beneath the trim as advertised. There are options about what to do with the wiring tail and trailer connector. I chose the method shown in the video...leave it rubber-banded in the storage well. Others have run it outside through available holes, but I did not want to leave it exposed to road grime. etrailer's videos were very detailed and shown on my specific vehicle for both the hitch and the wiring harness. Good values as well. If I were Draw-Tite (or Curt) I would include a complementary rubber plug with their logo...cheap advertising. 430539
MoHusker - 09/08/2018Works fine 129332
Randy K - 05/06/2015Great I didn't know a class 3 hitch needs a 1" ball thread. Most balls Iv'e seen have a 3/4" ball bolt or thread 59117
Dan M - 05/11/2014Very nice hitch. This is my third hitch purchase from etrailer.com and as usual, delivery was fast and the install went smoothly. The videos and user comments were very helpful. My vehicle is a few years old so the suggestion to chase the 8 mounting nut holes was spot on. There was a lot of mud and dirt which easily came out but would have been a pain to do while mounting the hitch. Also, the suggestion to spray down the rubber exhaust hangers and muffler heat shield bolts with penetrant (WD40) helped as well. The recommended draw bar and 4-wire harness also mounted beautifully. Got to love those factory installed rear wire harnesses which allow plug-in trailer harnesses on the Honda/Acura products. Total install took about 90 minutes which I think will be typical for a DIY'er who sprays down the bolts, chases the holes and without rushing or using air tools. Will buy again from etrailer.com 60422
Solid piece. 736853
Product car ready to install, no missing pieces. Just what I was hoping for. I would buy it again without any hesitation. Thank you, 736524
hitch work great . and great price thank you so much 736260
Great product and price 734572
Great fit. No play like some other mode ls. 734036
Everything I ordered arrived in perfect condition, and by following the installation instructions from your website, it all was installed very easily. Thanks for great products and great customer support. 732877
A serious hunk of steel! 732092
Solid, heavy duty. 729875
Great product, great instructions. Got it done in 40 mins 728081
All good. A+ in every regard. Tough as nails. Still in use and will be for quit some time, I'm sure. 722753
Did the job. Easy install. 722175
Well made and easy to install,customer service wasegrrat 720528
Do you have a question about this Ball Mount?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.