Putco Luminix Off-Road LED Light Bar - 22,800 Lumens - Narrow Spot Beam - 60" Long
Bumper Mounting Bracket for Putco 60" Luminix LED Light Bar

Video Transcript for Putco Off Road Lights - Light Bar - P10060 Review

Today we're going to review part number P10060. This is the Putco High Power 57 LED Luminix Off-Road Light Bar with 171 Watt and a 15 Degree Spot Beam Pattern. Now this part number comes with everything shown here on the table. Comes with the light bar, comes with the wiring harness. Also has 2 sets of mounting brackets, both long and short. Comes with the illuminated switch, the installation instructions and the mounting hardware which is already attached on the end of the light bar. Now this is a low profile LED light bar, which will deliver a bright focus light.

Gives off a 15 degree spot beam, which is created by the chrome-backed focused lenses. It is a very slim design so it will let you install this light bar in very tight spaces. It is a high quality light output from a single row of 57 3-watt Nichia LEDs. These are quality LEDs with a 50,000 hour lifespan. Now this light bar can be turned on and off with a wireless remote. We do sell that separately on our website.

It's part number P8770HF and it's usually listed as a related product on the product page. Now this light bar does have built-in safeguards. It uses a thermal control chips to help prevent LEDs from overheating. It has the over and under voltage protection which will keep the light bar operating at the correct voltage. This is a durable waterproof, corrosion resistant construction. It is a black anodized billet aluminum housing which is very lightweight and rustproof.

The mounting brackets themselves are a black powder coat stainless steel mounting bracket, help resist corrosion. The LEDs and the light bar are fully potted to protect the fragile components of the LEDs. Also has the industry standard protection against dust and moisture. This does have a easy installation with these included parts. This light can mount on your roof, your bumper. It gives a nice rugged look to your vehicle.

The 2 sets of adjustable mounting brackets, the long and the short. Basically, they would . You go to the very end here, it has the nut with the rubber cap. You just unscrew those, slide this on to the bolt coming out, put that back on, tighten it down and then mount your bracket to where you need to on your vehicle. We do also sell custom mounting brackets. They're sold separately on our website. They are also related as a related product on this product page. Now, the wiring harness. It comes with this wiring harness. It has the illuminated switch that plugs into this. Also has the industry the industry standard Deutsch connector. Now in a minute here, I'm going to go through this and show you how this all connects. Again, the directions I give you are very easy to understand. We're going to hook this up to a 12-volt supply to show you how bright the light is and then show you the pattern on the back wall. This part is made in the USA. Again the specs on this, it has 57 LEDs and they're 3-watts each, a total of 171-watts. The power draw is 13.5 amps and the input voltage is 12-volts to 36-volts DC. The operating temperature range on this light bar is -100 degrees Fahrenheit to 180 degrees Fahrenheit. It has a limited 2 year warranty. Now the light output, the brightness on this bar is 22,800 lumens. Again, the beam is a narrow 15 degree spot and the light gives off . The colored temperature of the light, it gives off 6,000 degrees Calvin. The dimensions, the overall length from edge to edge is 61-1/2 inches. It's 1-1/2 inches tall and 3/4 inch deep. Now what I'm going to do, is we're going to plug this in to a 12-volt power supply. Let me go through this wiring harness again. You could see it has the relay right here in the middle. All the wires come out of that. On this side, it has the wire with the Deutsch connector. What's nice, the Deutsch connector is a triple seal. It has a triple rubber seal there. It gives you a nice weatherproof connection. Here's your connector on your light bar so when you go and connect them, what's nice is a very snug fit. You push it in, it locks into place, it gives you that weatherproof connection. I'll tell you what we're going to do, let's just run this under the light so it doesn't get in the way of our patterns. We'll go ahead and plug the Deutsch connector in. Then on the other side, we have the wire. It has 3 wires coming out with connectors in the end. A red, blue, and a black. Those are for the illuminated switch. Basically, what we're going to do . Again, the directions will tell you if you look on the . There's 3 tabs on the back of the switch. They're number 1, 2, and 3. They tell you red goes to 1. Go ahead and install that. Blue goes to the middle or number 2. Go ahead and install that one. Then the very end one is the black wire, number 3. Go ahead and get them all pushed on. There we go. Now with that connected, the last wire coming out of the wiring harness is your power supply wire and you got to make sure, check it. It comes with the 15 amp fuse in this inline fuse holder. You can see there is the fuse. It's already installed so we're good. Then you have a wire, a red wire with an eyelet and a black wire. The red is for the power, black is for the ground. What we're going to do is hook up 12-volt power supply to the power and then we'll hook up the black wire to the ground. We got those hooked up. Now what we're going to do, I'm going to go ahead and turn off the overhead lights, we're going to go ahead and tun on the 12-volt power. Then what you'll see . I'll push the illuminated switch right here. You could see the switch is red dot right here. Push it off, it's a rocker switch, push it on and you can see it's illuminated. The lights of our light bar . You can see the 57 LEDs 171-watts. Pretty bright. What I'm going to do is try to rotate this. Again, it's very light. We'll just rotate this around and try to give you an idea of the light pattern you could see on the back wall there. It gives you a narrow, 15 degree spot pattern of light. Rotate this back around and we'll go ahead and turn this off. Go ahead and turn on our overhead lights, turn off our power. That should do it for the review on part number P10060. The Putco High Power 57 LED Luminix Off-Road Light Bar 171-Watts with the 15 Degree Spot Pattern. .