Instant Savings on Select Curt Products

Curt TriFlex Trailer Brake Controller - 1 to 4 Axles - Proportional
Universal Wiring Adapter for Curt Trailer Brake Controllers

Part Numbers: C51140,C51515

Retail:$136.13

Our Price: $104.23

After Instant Rebate

This item qualifies for Free Shipping


In Stock
Curt Automatic Leveling Brake Controller - C51140
zoom in icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.
Please enter a valid email address.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

pop out icon replay 360 icon
horizontal rotate icon

Product Images

In Use/Installed

Customer Photos




Curt TriFlex Trailer Brake Controller - 1 to 4 Axles - Proportional
part number: C51140

Proportional brake controller automatically levels when mounted within a 90-degree vertical range and a 40-degree horizontal range. Includes digital display, 9 sensitivity settings, reverse-polarity protection, and continuous diagnostics.

Features:

  • Brake controller activates trailer brakes in proportion to your vehicle's braking action
    • Automatically adjusts trailer's braking based on deceleration of tow vehicle
    • Activates immediately - no pausing like with time-delayed brake controllers
  • Automatic-leveling ability - internal sensor detects deceleration even if controller is not mounted flat
    • Position within 90 degrees up or down and within ±20 degrees side to side
  • 9 Sensitivity settings (boost settings) let you adjust initial braking power and aggressiveness
  • Triple-axis accelerometer is highly responsive, ensuring smooth, uniform stopping action
  • Continuous diagnostic check alerts you to any potential problems
  • Integrated safeguards protect your vehicle, the trailer, and the controller
    • Minimizes drain on car battery by entering power conservation mode after 30 minutes of inactivity
    • Keeps trailer brakes from overheating by reducing power output to them during prolonged stops
    • Defends brake controller and trailer breakaway systems against shorts
    • Prevents positive and negative power reversal with built-in polarity protection
  • Surface-mount technology (SMT) allows for consistent, reliable performance
    • Maximizes power output while producing minimal heat
    • Ensures superior operation in rough road conditions
  • Digital display communicates power and sensitivity settings and error codes
  • Built-in, slide-bar manual override
  • Mounting bracket and hardware included
    • Plug-in, vehicle-specific brake control adapter (sold separately) can be used for certain applications to reduce installation time


Specs:

  • Application: trailers with up to 4 axles (8 brake assemblies)
    • Designed for use with electric or electric-over-hydraulic trailer brakes
  • Dimensions: 3-1/4" wide x 4" long x 7/8" tall
  • Mounting:
    • 90-Degree vertical plane operating range
    • 40-Degree horizontal plane operating range
  • Limited lifetime warranty


Note: If your vehicle's 7-Way trailer connector has LED test lights built into it, the TriFlex brake controller will not be compatible.



Proportional Braking

With a proportional brake controller, you can get heavy-duty emergency braking, general braking, or slow-to-an-idle braking for your trailer automatically. The intensity with which your trailer brakes are activated and the rate at which they are applied are dependent on the deceleration of your tow vehicle. This means that, unlike time-delay controllers - which send the same amount of preset power to your trailer brakes every time - proportional controllers are able to adapt to every braking situation differently. So, if you slam on the brakes in your truck, your trailer brakes will activate with that same extreme intensity. And if you merely slow down as you approach a red light, your trailer will gradually brake in the same manner. Just set the initial power level, select a sensitivity setting, and you're good to go.


As long as the TriFlex controller is properly mounted as indicated in the instructions, it will sense - via an internal inertia sensor - how your tow vehicle brakes. This triple-axis, inertia-based sensor responds to the deceleration of your tow vehicle as you brake by signaling the controller to send out enough power to your trailer brakes so that they are activated with an intensity that matches. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.


Built-In Controls for Adjustable Power

Curt TriFlex Controls and Components

The above diagram shows the controls and components of the Curt TriFlex trailer brake controller.

  1. Digital display
  2. Thumbwheel power output control
  3. Sensitivity adjustment switch
  4. Slide-bar manual override

Output Control

During the initial setup process, use the thumbwheel on top of the TriFlex to adjust the output. The output control lets you set the maximum amount of power that will be applied to your trailer's brakes. Typically, the output is only readjusted when you experience changing road conditions or if you switch over from a heavy, loaded trailer to a much lighter, empty trailer, or vice versa. To get more power to your brakes, rotate the switch to the right. To decrease the power output, move it to the left. The output setting will appear on the digital display when you press the brake pedal or activate the manual override.


Sensitivity Settings

Once you have the overall power set, you can fine-tune the power output by adjusting the sensitivity of the internal sensor. Use the switch on the side of the TriFlex to achieve your desired degree of intensity.


Move the switch toward you to boost the power output, causing your trailer brakes to activate with more intensity right off the bat. This means that they will also reach maximum braking faster simply because they will start out at that higher intensity. This is particularly beneficial if you are towing a heavy load because the intensity required to stop that load may be far greater than that needed to halt your vehicle. Therefore, sending out more initial power to the trailer brakes - and causing them to reach maximum braking faster - allows you to better control the trailer so that it doesn't push your tow vehicle before coming to a complete stop.


There are 9 sensitivity levels (boost levels), with 1 being the least sensitive. At level 9, the sensitivity of the internal sensor is as high as it can go. When you change the setting, the display on the TriFlex will flash the level before reverting back to showing the power output.


Safety Features

The TriFlex offers advanced safety features to prevent damage to various components of your towing setup. When the TriFlex is not in use, it will be in power-saving mode, reducing the power draw to minimize drain on your vehicle's battery. This power-conservation mode begins after 30 minutes of inactivity and ends the moment your vehicle's brake pedal is pressed.


When you stop at red lights, or any time that your truck and trailer are at a standstill with the brakes applied for a prolonged period of time, the TriFlex will reduce the power output to your trailer's brakes, preventing them from overheating.


If ever there is a time that you need to brake your trailer separately from your tow vehicle, the manual override lever is easily accessible. Pushing this slide engages the brakes on your trailer with either full power or the maximum power allowed by the output level, depending on which setting you select. In addition, when you activate this override, the brake lights on your trailer will illuminate, properly warning those behind you of the braking action of your rig.


Automatic Leveling and Simple Installation

The self-leveling feature of the TriFlex ensures that the brake controller continues to function even as you drive up steep hills or through the mountains. Simply mount it in your cab at a vertical angle that is within 90 degrees, and the controller will level itself automatically. Make sure that the controller is also positioned so that the side-to-side angle is within ±20 degrees.


Installation is a snap. After mounting the TriFlex unit in your cab using the included bracket, hardwire one end of the included pigtail harness directly into your vehicle. The other end plugs into the brake controller. To transfer the TriFlex to another vehicle or to remove it for storage, just unplug the unit and remove the screws that hold it place in the bracket. Curt offers a spare mounting bracket (C51144 - sold separately) that can be used to affix the TriFlex in your other automobile.


Installation Accessories

For even easier installation, a vehicle-specific wiring adapter (sold separately) is available for most newer trucks and SUVs. One end of the custom adapter plugs into your vehicle, and the other end plugs into the controller - no hardwiring required.


Note: If a custom brake control wiring adapter is not available for your vehicle, one of the following will be required:

20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications

30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications


See also etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.


Surface-Mount Technology

Curt's TriFlex brake controller is built using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability, and durability.


Curt SMT Circuit Boards

Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? SMT circuit boards also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.


Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.



51140 Curt Tri-Flex Proportional Trailer Brake Control



California residents: click here



Universal Wiring Adapter for Curt Trailer Brake Controllers
part number: C51515

This wiring adapter is designed for vehicles that do not come equipped with a factory brake control wiring harness port. One end plugs into your Curt trailer brake controller while the other end splices into your vehicle's wiring.

Features:

  • Universal wiring adapter eases installation of your electric trailer brake controller
    • No need to wire brake controller directly to your vehicle
  • Wire end splices into your vehicle's wiring
    • Use on a vehicle that does not have a factory tow package or on one that has a brake control harness but is not equipped with a plug-in port
  • Connector end joins with the plug on your electric brake controller
    • Compatible with time-delayed and proportional brake controllers from Curt
    • Simple to plug and unplug control for removal
  • 2' Long, 12-gauge wires have protective covering to deter damage
  • Limited 1-year warranty


Installation of Curt Brake Controller Adapter

To install your Curt electric brake controller, you need to connect the wiring of the controller to your vehicle. Certain auto manufacturers offer pre-wired options, typically known as tow packages, wherein wiring is run for you from the dash to the trailer connector on the back of your vehicle. Usually when this is done, a port is installed at your dash so that you can easily plug in a brake controller. However, if no port is present, you will have to splice into your wiring.


With this universal adapter, you can install your Curt brake controller without having to wire the controller directly to your vehicle. If your vehicle has a factory tow package, just splice the pigtail end of the adapter into your vehicle's factory brake control harness wiring, and then plug the other end of the adapter into the controller. If your vehicle doesn't have a factory tow package, you'll have to hardwire the pigtail end of the adapter into your vehicle's wiring. Because only the adapter is hardwired to your vehicle, you can unplug and remove your brake controller at any time to transfer it to another vehicle or securely stow it away.


If your vehicle is not equipped with a factory tow package, you will need to purchase additional equipment to ensure that the signals from your brake controller are sent to your trailer's brakes. We recommend etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately).



51515 Curt Universal Quick Plug Brake Control Adaptor Harness with Pigtail



California residents: click here





Customer Reviews

Curt TriFlex Trailer Brake Controller - 1 to 4 Axles - Proportional - C51140

Universal Wiring Adapter for Curt Trailer Brake Controllers - C51515

Average Customer Rating:  4.8 out of 5 stars   (493 Customer Reviews)

Proportional brake controller automatically levels when mounted within a 90-degree vertical range and a 40-degree horizontal range. Includes digital display, 9 sensitivity settings, reverse-polarity protection, and continuous diagnostics. This wiring adapter is designed for vehicles that do not come equipped with a factory brake control wiring harness port. One end plugs into your Curt trailer brake controller while the other end splices into your vehicle's wiring.

- C51515
by: David03/27/2019

Not much to say about this. Is what it is. Plugs in to the curt triflex brake controller nice and firm. A little longer (it’s about 2’ long) than I needed in my 2011 Silverado but the excess wire tucked away nicely. 614612



- C51515
by: Robert09/30/2018

Product was easily located on website and was exactly what I was looking for. I had forgotten to take off of my old vehice before I sold it, so this allows me to plugin my Curt brake controller without having to cut the connector off of it. 570389



- C51140
by: Jon02/11/2019

Installed in my truck only took about a hour plugs in to the original 604157



- C51140
by: Jeff H.08/01/2013

Items arrived quickly. Hesitant to buy "Drawtite",as I was told 'Made in China". However, it says on label 'Made in USA'! Needed additional spacer for 'middle' bolt.? Fairly easy install. Curt brake controller should be easy as well. All in all, a 'square deal! 92715


Comments

Hitch is fine.Curt controller had a malfunction, factory support -superb! Sent a new unit in 2 days!

Jeff H - 01/30/2015

9096

- C51515
by: Christopher03/12/2018

The items I ordered I got in a timely manner great job 484308



- C51140
by: Rick10/10/2018

Works very well ! 573332



- C51515
by: BiscuitsNGravy10/21/2013

I own a 2008 Chevy Silverado. I ordered the brake controller - C51515 and the universal wiring adapter on Friday and received it on Tuesday. My friend who is a mechanic installed it in about an hour on Wednesday. I towed my camper trailer to Lincoln, NE (about a 5 hour trip) on Thursday and returned on Sunday. After reading the settings instructions, all stops were made smooth and firm. Etrailer.com was great and the Curt Trailer Brake Controller is excellent! 104632


Comments

I have enjoyed the use of the electric brake controller. The stops are always safe and smooth. Im glad I got it for my truck and Ive never had a problem with it. I just need to get out and use my camper more! The initial contact with etrailer.com was very favorable and I will do business with them again when I need something for my trailers or tow vehicles.

BiscuitsNGravy - 10/21/2014

7356

- C51140
by: Bill02/26/2019

seemed to work great towing our 16' iPod travel trailer! 608503



- C51140
by: Howard S.04/06/2017

I bought a 7 pin trailer wiring/brake connection for my Dodge pickup. I installed it myself, the instructions were absolutely clear and correct. It was an easy installation. In the year since, I've pulled my trailer (tandem axle, 16') many times. The brakes continue to work perfectly as well as the lights. The connectors are solid, all work just like new. I recommend Etrailer parts and their people 100%! 363500


Comments

Still using the products no problems, everything’s works great.

Howard S - 04/06/2018

36954

- C51515
by: Mainly Dave07/22/2015

Recently used this kit to install electronic brakes on a 2014 FJ Cruised. Absolutely essential and worth every penny! Instructions straight forward and everything included! 213491


Comments

Have been using this product for a year now. Commonly haul 2-3 tons. Absolutely no problems and the braking system works well. Adjustments based on load are easy. Highly recommend!

Mainly D - 07/22/2016

19561

- C51515
by: Ted07/03/2014

I purchased the wiring harness to aid with hooking up the Curt Brake Controller I had previously purchased. The shipment was fast. The product was perfect. The on-line installation video was perfect and allowed me to complete the installation like a professional. I have never purchased anything from etrailer.com .... but should I ever need anything in the future, they will be my first choice. 139007


Comments

Perfectly. No issues at all with wiring or controller.

Ted - 07/03/2015

13016

- C51140
by: Jason S07/30/2017

I recently bought a Kurt trailer brake controller with adaptor. I have to say, that it was the easiest thing to hook up. The product was also shipped to my home very fast. I did not think I was going to receive the package until the next week, but it came just in time to use it the following day for my work. i Love ordering products from etrailer, I have only had really great service and good products from them. I will for sure, order from them again. 414526



- C51140
by: Joe B.11/21/2015

Easy to install and set up. I can't believe the difference between this proportional controller and the simpler time delay type. Between the power output adjustment and the sensitivity adjustment, you can quickly and easily adjust the controller for your trailer. It took me about 5 minutes to dial it in perfectly! No more jerky trailer brakes! Thank you E-Trailer! 232383



- C51515
by: Kent E.06/05/2016

Wiring up a brake controller can be tricky. Routing the wire from the hitch to the firewall and finding the right wire on the brake are the hardest part, but etrailer will do their best to help. Consider running the wire inside the car along the door bottom just under the carpet. This avoids problems with the tie-wraps under the car -- there just isn't anywhere to tie wrap under the middle of the car. Use "loom clamps" ordered separately to solve this problem, if you go under the car. To find the right brake wire without cutting insulation, use the fish wire from the hitch install to contact the end of the wire inside the connector (from the back). Then touch the fish wire with the continuity tester and apply the brake pedal. My brake had a four wire connector and I found the right one on the second try. If you find a hole in the firewall with a rubber plug in it, don't discard the plug. Make a short slice in it with a razor blade and push the wires through. You may have to work the wires around to get them through the carpet. Be patient. Be sure to watch all the videos and allow plenty of time, taking a break before you tackle the hard parts. Rest assured that doing it yourself is better than allowing UHaul to cut corners and charge you labor. :-) If you are doing the hitch install and four-wire harness, those are much easier. If you are installing the hitch alone, be sure to have a magnet wand for when you push the bolt up into the frame rail. If I had it to do again, I would use a little electrical tape to hold the bolts down so a slight bump wouldn't knock them up. 257414


Comments

Ive not had any trouble with the hitch or the brake controller. I can tow my tear trailer anywhere I want and the hitch protects my mufflers from damage when I go offroad. Nice extra benefit.

Kent E - 01/23/2018

33496

- C51140
by: Dave10/14/2018

I am very excited to try it, however the quick connect, doesn't seem to fit my 2004 3/4 ton Chevy Express van. Th brake control harness #51451. It's for the Trifles brake controller. If it is the correct harness I cannot find where to plot in . The vehicle end of the harness will not fit available spots on fuse block . Any help would be appreciated. Thanks Dave 574308


Comments

The 2004 Chevrolet Express Van does not have a plug and play adapter available for the brake controller at this time. The C51451 will not have a place to plug in in your vehicle. The adapter you will need with the curt triflex is part # C51515
Universal Wiring Adapter for Curt Trailer Brake Controllers
$9.51
. The part C51515 pig tail plugs into the wiring that is coming out of the back of triflex. There is some wiring that needs to be done with this brake controller installation. If your 2004 Chevrolet express van has a towing package from the factory the blue brake wire is already ran from the back of the vehicle to the front. It is located under the dash near the emergency brake pedal. The blue wire from the brake controller wiring pigtail will butt connect to the blue wire that was ran from the factory. You will also need kit part # 5506
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
$42.86
. Using the duplex wire from the kit you want to butt connect the black wire to the black wire coming from the brake controller. Using a ring terminal connect the black wire to the 30 amp circuit breaker included in the kit that you will install under the hood. Then using an extra cut piece of black wire connect from the circuit breaker to the positive side of the battery. The white ground wire will then connect to the negative side of the battery. The red wire from the brake controller butt connects to the brake switch wire and will need to be located in the van. In a Chevrolet express van the brake switch wire is normally light blue and located in the Body Control Module of the van. The BCM is normally located behind the passenger side dash. The brake switch wire on the van is typically the light blue wire but you want to use a circuit tester to test for function. You are looking for the wire that only shows power when the brake pedal is pressed. Once you have located that brake switch wire, connect the red wire from the brake controller to that. If your chevrolet express van has a towing package it should have a round plug with a cap inside the drivers side frame rail at the back of the van. You can now use a part # 30955
Replacement Custom Multi-Tow 7-Way and 4-Way Trailer Connectors
$38.88
to give the van a 7 way connector. If your van does not have a towing package the blue wire will not be ran for you. You will need part # ETBC7
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
$54.04
and not the part # 5506
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
$42.86
. The ETBC7 includes the 7 way connector, circuit breakers and duplex wire. The 7 way connector will need to be wired to the front of the vehicle before you can finish the installation I described above using the duplex wire in the kit. You also need a 4-way connector to plug into the 7 way connector part # 118392
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
$22.95
for the 2004 Chevrolet express van. I have attached FAQs on wiring in a 7-way connector.

-- Heather A - 10/16/2018

44706

- C51515
by: Frank S02/14/2014

this went into my VW Touareg which requires the relay modification described in the Technical Bulletin. Because ground and +12V is already present in the harness, instead of running additional cables, I soldered the relay right into the cable, making it a clean plug and play setup which is 100% removable. I also bought the VW housing and wire kit to complete the install 116584



- C51515
by: George D10/17/2015

good quality and works with brake controller so you don't have to rig it up its all there glad i bought it thanks 230175


Comments

Very easy to do still working great

George D - 10/16/2016

21546

- C51140
by: William g09/22/2018

Fortunately my F150 had the trailer package so the pigtail plugged right in. Only snag was I had to fabricate a piece to attach to the instrument panel (lower right) to get the correct angle they specify. That took some work. But it all came together nicely. See attached picture. The brake control works great. Good price. 567828



- C51140
by: Mike R.09/22/2014

Small size is convenient - easy to mount in a Tacoma. When setting it up for a single-axle 2,200-pound tent trailer with a brand new Dexter axle, I was surprised to find I have to run at the maximum output and sensitivity settings, but it works fine. 152489


Comments

Make sure the brakes are properly adjusted. They should be exerting a slight drag on the drum when spinning by hand. If the brakes are not adjusted correctly, you may be exerting more wear on the magnet than is necessary.

-- Patrick B - 09/29/2014

7032
Comments

I dont know what changed, but the controller is working as expected now - I am pleased with its performance and convenient size.

Mike R - 09/16/2015

15030

- C51140
by: Robert A.04/21/2017

The unit with the matching installation cable was easy to install once I found the factory installed plug-in port on my 07' Dodge Quad Cab. The videos didn't have my truck model and I had to go to the Curt mfg website to find a picture of the the location of the port. I have not hooked up the truck with the trailer yet to test and adjust the brakes but the controller installation and functionality test was very easy to accomplish and went smoothly with the instructions provided. 370441



- C51140
by: Chris H07/31/2017

I purchased this controller along with the direct fit wiring harness and 7 way trailer harness for my 2000 F250SD. Install was easy. I would highly suggest buying the direct fit harness with this controller (I was replacing a spliced in system that was having intermittent issues). The only trailer I tow with brakes is an 18' landscape/utility trailer that may be loaded with 1000# one week and 7000# the next, so the inertia driven system should make for a much smoother ride. Service was great, really appreciated the follow up email to make sure the product arrived in good order and all my needs had been met. Etrailer will be my first stop for trailer related needs in the future. 412923



- C51140
by: Mainly Dave07/22/2015

Installed and use on a 2014 FJ Cruiser. Need the wiring kit for the FJ. Installation was straight forward and everything needed was included. Took me about 2 hours but no problems. Using the unit is easy to understand. My only concern is that it does not seem to be able to lock up the brakes [even with the manual function.] But this might be due to my brakes being worn and not used recently. Have towed a fairly heavy load once [~3500 lbs,] and I am pleased with the braking function. I recommend the product. 213490



- C51140
by: Vincenzo09/05/2018

Wow! All works to perfection ! From the Website wade of specification of what I needed for my set up to fast delivery and plug n play install ! This is my second order from etrailer & will be for all my needs! I installed it to my right knee side , so not to hit it in & out daily, but any place will work - tie up extra wire securely. Safe journey !! 561685



- C51140
by: Tammy H.01/01/2017

I connected the Curt Brake controller into my 2007 Toyota 4runner. It took 5 minutes to hook up using the curt wiring adapter for my vehicle. I pulled a 16' aluminum stock trailer with one horse in it. There were no problems with braking and the braking action was very smooth on the trailer. I also have a weight distribution on the trailer which helps with using the Toyota in an "emergency" tow. The horse had an easy 3 hour tow with smooth braking and no swaying. Thanks etrailer for all the tools that make farm life easier. 329228



- C51140
by: Tom and Anita09/19/2016

Yes I received my order and installed the brake controller. All seems to be fine, although I have yet to tow with it yet. Here are a couple photos of the installation in my 2010 Toyota Tundra. 296409



- C51140
by: Joe R04/24/2014

placed into my 2014 RAM 1500 put it in place only took about a half hour with the right harness. 127226


Comments

Just curious, how much weight have you towed with the controller and how well did it perform? What setting did you run?

-- comment by: John P - 09/26/2015

15232
Comments

Hi John I have a ram 1500 V6 . My camper is 19 ft about 4300 LBSI have the sensitivity setting at L7 and the thumbwheel set around 20 to 25 .. If every thing reads ok from the codes .the setting are easy to test with a short drive .Adjust your settings to your liking. after setting for awhile like over the winter or pulling out from a seasonal site you may need to run little heaver on the break for a short time . It has plenty of power to stop you with just the trailer brakes .

-- comment by: Joe R - 10/13/2015

15525

- C51140
by: Bill Y.09/28/2015

I installed this unit, hooked up my travel trailer and had it all calibrated and ready to hit the road in less than an hour. Took a 300 mile trip a few days later and the unit was flawless. Forget the old time delayed units, this is the way to go. Also, get the pigtail that is designed for your particular vehicle, it makes installation a snap (plug in to your vehicles available plugin and into the back of this unit) couldn't be simpler. Very satisfied with the unit and with e-trailer.com. Great products, great service. 228079


Comments

Still satisfied, works great.

Bill Y - 09/27/2016

21272

- C51140
by: Alan11/17/2017

2003 Ranger XLT Installation was fun! I tend to ignore instructions especially when those instructions mount the device where my knee is constantly banging into that device. See the photo. Would loved to have a longer extension cable to reach into engine compartment. If you are not mechanically and electrically gifted, have somebody that is do the installation. Had the device not initialize once at the beginning of a trip. After thirty minutes of trouble tracing, decided nothing was wrong, unplugged the cable for a few minutes then reconnected and initialization completed correctly and I had brakes. Now I unplug the device whenever I'm not towing. 452856



- C51140
by: Ryan R04/12/2015

Installation was easy. Product works well. The power and sensitivity adjustments are very useful. 184853


Comments

Everything is still working fine.Thanks for Asking

Ryan R - 04/21/2016

17533

- C51140
by: Jared S.10/12/2017

The trailer brake worked out very well. Installation was a little difficult for someone with no experience, but the videos on etrailer were great. My only issue would be that I only had about a foot of spare cable left at the end of the install, a few more feet would have helped me feel more comfortable. Otherwise, great product and site. Having all the right equipment and videos appropriate for my Jeep were essential. 442038



- C51140
by: Doug S09/15/2013

To be honest, haven't installed yet. Have to run wiring in 2 trucks as neither has factory wiring. I want mounting to be not noticeable if I sell either vehicle. Based on reviews, and having my hands on it and the printed directions I believe it will fit my greatly fit my needs. I have a one month plus to get one vehicle ready for a road trip. LOL, I like to plan ahead. Will write more when I get working. 99999



- C51140
by: Robert07/15/2018

Item is smaller and lighter than expected. Easily mounted using existing dash screw. Pigtail wire kit that was also ordered here made installation a snap. I like the display and the ability to manually apply trailer brakes and increase braking force on the fly. Less than a 5 minutes install. Installed only, haven’t used it yet. Will have to update later. Rig is 2007 Dodge Ram 2500 4X4 CTD. 542058



- C51140
by: Lee A07/23/2013

I received my Curt triflex brake control in less than a week from ordering on line. It was so easy to put in and set up. I couldn't believe it. Just plug and play. 91176


Comments

It didnt. It would not adequately slow down or stop my 34 fifth wheel. I pulled it out and installed a Prodigy. The Prodigy works just fine.

Lee A - 01/21/2015

8796

- C51140
by: Steven08/29/2018

I wasn't very pleased with this brake controller. It seemed to frequently require resetting, which involved stopping, getting out and unplugging/replugging the brake cable. I was never able to get a good understanding of the controls either - there was a dial for gain and a slider for "aggressiveness" (huh?). Also, after using it for about 10 months, I thought the brakes on my trailer needed replacing - it would brake some, but not much. About that time I bought a new truck with built-in brake controller and the trailer brakes worked great again. Had to be due to the controller... 559619



- C51515
by: John08/23/2019

WIRING HARNESS FIT AND EASY TO INSTALL 692792



- C51140
by: Richard08/17/2019

Easy installation. Works great 690482



- C51140
by: Robert08/16/2019

By far one of the best customer service experiences EVER!! We recommend etrailer hands down! 689950



- C51140
by: Carl08/15/2019

The unit looks very good. I'm putting it on my 2019 Silverado to pull a travel trailer. The truck is prewired and this unit just plugs in. I recommend this controller. 688793



- C51140
by: Nicholas08/07/2019

I chose this controller for it's 9 levels of sensitivity as other controllers I've had were too aggressive on even the lowest setting and only had 3 sensitivity levels. I have only pulled a couple loads using this controller; it was not too aggressive and performed well pulling a 30-ish year old trailer with tandem mobile home axles. The trailer was loaded to the max capacity of the axles, well maybe even a little over, and while I did have it on the most sensitive setting at max gain, I did not want any more braking capacity. Ordering it with the factory plug adapter made installation a breeze on my 96 Ford F250. 681994



- C51140
by: Jason J08/06/2019

Does the job. It’s not great at low speed maneuvering. It seems to apply the break pretty heavily when you’re moving around a parking lot or in a neighborhood. Otherwise I’m very happy with it’s function. 681346



- C51140
by: James07/29/2019

Easy to install and worked great right out of the box. 677791



- C51140
by: Pat V07/26/2019

The hardest part of the job was finding the pre-installed connector on the Tacoma. It is tucked in behind a wire bundle so you have to know where to look. Once found, simple plug and play. 678098



- C51140
by: James07/23/2019

Missing parts arrived, thanks Angela W! 674475



- C51140
by: Josh07/23/2019

Product made a constant clicking sound. E trailer wouldn’t allow it to be returned due to it having been installed. Wouldn’t have known about the clicking issue without installing it. Had to replace with a different controller. Poor quality control on this product and customer support wasn’t much better. 673934


Comments

According to Curt, the clicking heard is an internal switch actuating, and the noise is completely normal.

-- Mike L - 07/24/2019

58180

- C51515
by: Stephen L.07/22/2019

great product makes it very easy to connect to vehicle. 673745



- C51140
by: Bob07/21/2019

It was fast service and exactly what they said. 673425



- C51140
by: Ian07/05/2019

2011 Pathfinder Silver. I had previously swapped out the original flat 4 plug with the OEM 7-pin harness. Bought this controller + connector and installed it in < 5min. Could not have been easier to connect. I'll be able to test it in a few days once I get my pop-up from storage. 666871



- C51140
by: Charlied07/03/2019

Preforms as presented. Setup, pairing was a breeze. Highly recommend your consideration. 666157



- C51140
by: Dennis06/29/2019

Excellent service and great products 664341



- C51515
by: Joseph06/26/2019

the item I received was exact what I needed and olivia did great job helping me get what I needed and told me if I needed any other help to call again. thank you JOE 663240


Show More Reviews
504
504


Ask the Experts about this Brake Controller
Do you have a question about this Brake Controller?


  • Recommended Brake Controller Wiring For 2017 Hyundai Santa Fe
  • There is no brake controller harness on your 2017 Santa Fe so it will require some hardwiring. First, you will need part # ETBC7. This plugs into the 4-way connector on your Santa Fe. You will then need to run the additional wires to complete the installation of the brake controller. I have attached a drawing that shows how the wiring is run for the # ETBC7 and the brake controller. The Curt TriFlex Brake Controller, part # C51140 is a proportional controller that will apply the
    view full answer...

  • Correct Wiring Harness for the Curt Triflex Brake Controller
  • The Curt Triflex brake controller # C51140 is an excellent choice when adding a brake controller to your vehicle. This brake controller activates trailer brakes in proportion to your vehicle's braking action, automatically adjusts trailer's braking based on deceleration of tow vehicle, and activates immediately with no pausing like with time-delayed brake controllers. But when trying to find the correct wiring harness to install it into a 2008 GMC Denali XL, the answer is the Universal
    view full answer...

  • Parts Needed to Install Curt TriFlex Brake Controller in GMC Van and Ford F-53
  • To install the Curt TriFlex # C51140 trailer brake controller in your 2006 GMC Savana Van you will need to wire in harness part # C51515. Vehicles with the 7-way tow package have the blue output brake wire already run from the back to the front. It is located under the dash near the emergency brake pedal. This connects to the blue wire on the harness. The white wire connects to battery negative, the red wire connects to the cold side of the brake light switch and the black wire connects
    view full answer...

  • Are the Curt TriFlex # C51140 and Curt Adapter # C51453 a Fit for a 2014 Ram 1500 4WD 5.7 Hemi
  • You have exactly what you need for installing a brake controller in your 2014 Ram 1500. Brake controllers, like your Curt TriFlex # C51140, aren't necessarily vehicle specific, but the plug-in wiring adapter harnesses are. The correct one for your 1500 is the Curt # C51453 that you referenced. This will plug into the port under your driver side dash and allow you to easily install and remove the controller when needed.
    view full answer...

  • Troubleshooting Curt TriFlex Trailer Brake Controller Showing Red Dot and Number without Trailer
  • If the red dot on your Curt TriFlex Trailer Brake Controller # C51140 remains on without a trailer connected, this can be an indication that the red wire from the controller is connected to the wrong side of the stoplight switch on your vehicle. I recommend verifying that the red wire is connected to the cold side of the stop light switch, which is the wire that ONLY receives power with the brake pedal depressed, and no power with any other function. You can use a circuit tester like #
    view full answer...

  • Where Is Brake Controller Install Port on 2017 Ram 1500
  • To install a Curt brake controller like the part # C51140 in a 2017 Ram 1500 the correct install harness is the part # C51458. If you check out the install video I attached below you'll see exactly how a similar brake controller installs on a 2017 Ram 1500 like what you have. Fast forward to the 2:30 section of the video to see where the port is found.
    view full answer...

  • Installing the Curt TriFlex Trailer Brake Controller on a 2017 Chevrolet Colorado
  • I am having a hard time trying to understand your problem so bear with me here but it sounds like you are trying to install the Curt TriFlex Trailer Brake Controller part # C51140 on your 2017 Chevrolet Colorado with the Universal Wiring Adapter part # C51515. If that is the case then you are off to a great start as this is the correct harness for your Colorado. If your Colorado came with a factory 7-way then the wires you need to attach the harness to are already ran underneath the
    view full answer...

  • Brake Controller Install Harness for Installing Curt Triflex in a 2016 Ram 1500
  • To install the Curt Triflex brake controller part # C51140 in your 2016 Ram Bighorn 1500 all you need is the correct install harness, part # C51458. The truck pigtail is right above where your right foot would be covered in a foam tape.
    view full answer...

  • Can Curt TriFlex Trailer Brake Controller # C51140 Be Temporarily Disabled When Backing Up
  • I did some research on this controller for your 2006 Chevrolet Silverado, and there are no features available that will turn the Curt TriFlex Brake Controller, part # C51140 off. The best way to temporarily disable the controller when you intend to back up is to unplug the trailer. If you were to unplug the controller, it would have to be reset when it is plugged back in. I spoke with my contact at Curt and they strongly advised against doing this because if someone failed to reconnect
    view full answer...

  • Is there a Brake Controller Wiring Harness for a 2008 Mercedes GL550
  • There isn't an aftermarket brake controller wiring harness that will fit your 2008 Mercedes GL550 so you have a couple of options. First you can see if there is an adapter from a Mercedes dealer with one end that plugs into the port under the dash and the other end with just wires. Then you could wire the controller to that adapter harness. The other option is to determine the functions of the pins in that port using a circuit tester such as # 40376 or a meter if you have one. One pin
    view full answer...

  • Parts Needed to Install a Trailer Brake Controller on a 2009 Audi Q7
  • If your 2009 Audi Q7 does not have a factory trailer connector at the rear of the vehicle then you will need to install both the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit part # 119250KIT and the Universal Installation Kit for Trailer Brake Controller part # ETBC7 in order for a brake controller to work. Trailer brake controllers are universal and can be adapted to fit any vehicle with the correct wiring harness. The correct wiring
    view full answer...

  • Troubleshooting Curt TriFlex Brake Controller that Flashes L.6
  • L.6 is the sensitivity setting your Curt Triflex # C51140 currently has. It has a sensitivity range between L.1 through L.9. Since Curt controllers are known to be a bit buggy this isn't super surprising that you are seeing this. What Curt would recommend is to unplug the controller for a few seconds to let it reset and then plug it back in. Normally this takes care of strange behavior like this.
    view full answer...

  • Where Is the Brake Controller Plug on a 2008 Dodge Ram 1500
  • The correct brake controller adapter plug you are looking for is blue however, it will only have four pins as you mentioned which means the one you have located in not correct. The correct plug you will be looking for and can find in the attached photo is located to the left of the intermediate shaft on the steering column. This plug can also be seen in the attached video. The correct adapter for you if you have a Curt brake controller like the Curt TriFlex Trailer Brake Controller part
    view full answer...

  • Curt Trailer Brake Controller Only Works with Manual Override on a 2014 Toyota Tundra
  • When a brake controller works with the manual lever but not with the brake pedal that usually indicates a problem on the red wire. The red wire is the input wire that tells the controller you are stepping on the brake pedal. The most common issue with the red wire is actually a blow stop light or CHMSL fuse. Use the owners manual to find the stop light or CHMSL fuse to check it. You will also want to test the red wire using a circuit tester such as # ALL640595. With the brake pedal
    view full answer...

  • Parts Needed to Install Brake Controller in 2015 Ford Flex with Tow Package
  • To install the Curt Triflex part # C51140 in your 2015 Ford Flex that you completed the tow package for the only harness you need is the part # C51432 which will plug into the connector under the dash of your Flex that you mentioned.
    view full answer...

  • Location of 7-Way Tow Package Wires on a 2005 Chevy Tahoe to Install a Brake Controller
  • If your 2005 Chevy Tahoe did not come with a factory installed 7-Way trailer connector then you will need to add one using # 30955 which plugs into a connector located above the spare tire under the vehicle. I have included a picture that shows what it looks like for you. If your Tahoe doesn't have that round connector above the spare tire then there would be a wire bundle instead in the same location. And if your Tahoe came with a factory 7-Way then there is no other connection you
    view full answer...

  • Curt Triflex Trailer Brake Controller Shows Power All the Time on Blue Wire
  • You should only be seeing 12 volts on the blue wire on the brake controller, # C51140, when the manual override is used. If there is constant power all the time then there is either something that is miswired or a problem inside the controller and it will need to be replaced. Brake controllers do send back a minimum amount of voltage to check for a connected trailer but it should not be enough to activate the brakes. In the truck cab you will need to sever the blue wire several inches
    view full answer...

  • What Problems Does the Curt Triflex Brake Controller Have with 7-Ways With LED Test Lights
  • What happens is that the load that LED puts on the brake output circuit tricks the brake controller into thinking that there is a trailer connected and the brake controller will start activating regardless if there is a trailer connected or not. Technically it would work just fine with a trailer, its just that it will always activate regardless if there is a trailer back there or not. I attached installation instructions and an install video for you to check out also.
    view full answer...

  • How Does Brake Controller Install in 1993 Chevy 4x4 Z71
  • The 1993 Chevy C/K trucks like yours do not have a factory pre-wired brake controller port so you'd have to hardwire the controller to your existing 7-way. For a wiring kit to install the brake controller to the 7-way you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that
    view full answer...

  • Parts Needed to Install Curt Triflex Brake Controller in a 2002 Chevy Suburban
  • All you need to install the Curt Brake Controller part # C51140 in your 2002 Chevy Suburban with the factory 7-way is the install harness part # C51342 that you referenced. This harness plugs into the port under your dash and it will be fully active and ready to go once you mount it.
    view full answer...

  • Adapter for Curt Venture Brake Controller on VW Touareg
  • In order to use the Universal Wiring Adapter for Curt Trailer Brake Controllers # C51515 with your Curt Venturer # C51110 brake controller, you will need additional parts from your Volkswagen dealer. Please see the attached help article on installing a brake controller in 2005 and up Volkswagen Touareg's. It states in part: "To install a brake control on a 2005-current Volkswagen Touareg or Porsche Cayenne using the factory brake control connector, you will need to assemble a brake
    view full answer...

  • Troubleshooting Curt Brake Controller Installation in 2007 GMC Sierra New Body Style
  • First I suggest making sure you are testing the brake circuit pin on your Sierra's 7-way trailer socket. If you refer to the linked photo of a trailer connector you will note the brake controller's output is carried on the pin at the 5:00 position; the ground is at the 7:00 position. If you happened to test the 12V auxiliary power circuit, carried on the pin at the 2:00 position, it will have power at all times. I see that you purchased Curt Universal Wiring Adapter # C51515 which
    view full answer...

  • Brake Controller Recommendation for a 2012 Mercedes GL450
  • In order to install a trailer brake controller on your 2012 Mercedes GL450 it will require hardwiring in the controller unless the Mercedes dealer has a wiring harness specific for a brake controller and your vehicle. If they do then you will need to wire in the controller to the Mercedes harness by function. On a brake controller, the wire functions are as follows: White is ground Black is 12 volt power Blue is output to the trailer brakes Red is input from the brake switch On
    view full answer...

  • Brake Control Harness # 51515 Installation Process in 2008 and 2013 Chevrolet Silverados
  • The Curt Brake Controller Harness you referenced, part # C51515, can be used for both the 2008 and 2013 model years of the Chevrolet Silverado since it is a universal-fit harness. For your 2013 Silverado you will want to follow the procedure outlined in the linked article. Please refer to the photo provided which shows the vehicle tow package wiring that can be found under the dash. You will connect these wires to the leads on the Curt harness as per the article, using butt connectors
    view full answer...

  • Brake Controller and Install Harness Recommendation for a 2006 Jeep Commander
  • The correct Curt brake controller install harness you will need for your 2006 Jeep Commander is the part # C51515 that you referenced. I would recommend you go with a proportional brake controller with it like the Curt Triflex part # C51140 as it will sense the amount of braking you are applying with your vehicle and will provide a proportional amount of braking power to the trailer. Some models will require a wiring kit to run wire to the battery. This may require drilling a hole
    view full answer...

  • How to Install the Curt Wiring adapter # C51515 on a 2008 Chevrolet Silverado
  • To install the Curt Wiring adapter # C51515 in your 2008 Chevrolet Silverado you will need to hardwire it under the dash. To be sure that the wire bundle you found under the dash is the correct set of wires I would check the white tag for any indication as to what each wire is for. If none of them have labeling then it would be best to test their functions with a circuit tester like part # PTW2979. You will then connect the following wires from the Curt adapter to the following functions: Blue
    view full answer...

  • Wiring Adapter for Curt Electric Brake Controller on 2016 Toyota Tacoma
  • We do offer the Universal Wiring Adapter for Curt Trailer Brake Controllers # C51515. This adapter will connect with the plug on the back of the Curt electric brake controller on one end and the other end will allow you to hardwire install the brake controller. If you need to add a 7-Way to your tow vehicle, the # C51515 adapter will work well with the Universal Installation Kit for Electric Trailer Brake Controller # ETBC7. The instructions for this hardwire installation are linked
    view full answer...

  • Troubleshooting Brake Controller Not Allowing Truck To Start
  • For your 2014 Chevy Suburban, no plug is present under the dash, but the needed wires are already run. You will connect the brake controller wiring with the vehicle wiring already present under the dash using the Universal Wiring Adapter for Curt Trailer Brake Controllers # C51515. It seems the 2007 to 2013 brake controller wiring was carried over into 2014 for your vehicle. I've attached and article to assist. The issue you are experiencing is most likely because you have a plug
    view full answer...

  • Custom Wiring Adapter for 2012 Chevy Silverado Curt Brake Controller
  • If you are looking for the custom adapter for the Curt Reflex Trailer Brake Controller # C51130, you will need the Universal Wiring Adapter for Curt Trailer Brake Controllers # C51515. Unfortunately, no factory plug is present under the dash on your truck, but the needed wires are already run. You will connect the brake controller wiring with the vehicle wiring already present under the dash. It is a two foot long wire. These are twelve gauge wires with a protective coating to prevent
    view full answer...

  • White Ground Wire Is Taped To Orange Wire 2009 GMC Sierra 1500 Brake Controller Install
  • You want to use the white wire in your photo for the ground. The other orange wire is the CHMSL circuit which stands for center high mount stop light wire. It is not used by a brake controller so you can tape it up and stow it out of the way. You will need 4 wires to install the brake controller, 12 volt power (red and black in your photo), trailer brake output (solid blue in your photo), stoplight circuit (light blue with stripe in your photo) and ground (white).
    view full answer...

  • When Does Brake Output Circuit of Vehicle 7-Way Have Voltage
  • The brake output circuit on a 7-way (5:00 pin) will only have as much voltage on it as the brake controller is sending. Typically this going to depend on the amount of gain selected on the controller and other factors like brake controller style and ramp up speed of the controller. The only time the circuit would have voltage without the brake pedal being applied would be if you had the manual override lever of the controller slid. I attached a couple help articles on brake controllers
    view full answer...

  • Troubleshooting Curt Venturer Brake Controller Installed on 2011 Dodge Ram 1500 Pickup
  • Getting a single green LED on the display indicates that there's no trailer connected. Since you're getting this with the trailer connected, it would seem to indicate that the brake controller isn't 'reading' the trailer for some reason. The most common reason for this to happen would be a dirty, corroded or damaged connector on the vehicle or the trailer. Examine the trailer connectors, and ensure everything is clean. If you see any white or green corrosion on the pins or sockets of the
    view full answer...

Info for these parts were:

Test Fit:
Joe V
Edited by:
Leah B
Photos by:
Jackie C
Expert Research:
Michael L
Video by:
Andrew K
Written by:
Lindsey S
Expert Research:
Michael H
Installed by:
Jeff D
Expert Research:
Jameson C
Video Edited:
Joshua S
Test Fit:
Nicholas E
Video Edited:
Jacob T
Test Fit:
Rick A
Expert Research:
John H
Updated by:
Adele M
Video Edited:
Andrew L
Expert Research:
Adam R
Video Edited:
Kathleen M
Video by:
Dustin K
Test Fit:
Shane T
Expert Research:
Rachael H
Expert Research:
Jeffrey L
Video Edited:
Sue W
Test Fit:
Randy B
Video Edited:
Chris R
Updated by:
Sarah W
Updated by:
Amanda M
Video Edited:
Zach D
Test Fit:
Brent H
Test Fit:
Shane H
Updated by:
Kristina F
Updated by:
Isabelle B
Photos by:
Jim W
Test Fit:
David F
Test Fit:
Ryan G

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.