Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Honda

Part Numbers: 39510,3070-P

Retail:$117.88

Our Price: $77.08

You Save: 35%

Orders above $99 qualify for Free Shipping


In Stock
39510 - Under Dash Mount Tekonsha Brake Controller
zoom in icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.
Please enter a valid email address.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

pop out icon replay 360 icon
horizontal rotate icon

Product Images

In Use/Installed

Customer Photos




Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
part number: 39510

Proportional brake controller can be mounted within a 90-degree vertical range. LED monitor indicates braking action of trailer. Fine-tune power adjustment lets you set braking intensity to suit your towing needs.

Features:

  • Brake controller activates trailer brakes in proportion to your vehicle's braking action
    • Automatically adjusts trailer's braking based on deceleration of tow vehicle
    • Activates immediately - no pausing like with time-delayed brake controllers
  • Multiple mounting options
    • Position within 90 degrees in the vertical plane
  • Fine-tune adjustment for braking power and aggressiveness
  • Green LED monitors a secure connection with trailer
  • LED monitor changes color to alert you to braking action of trailer
  • Built-in, slide-bar manual override
  • Plug-in, vehicle-specific brake-control adapter can be used for certain applications to reduce installation time


Specs:

  • Application: trailers with up to 4 axles (8 brake assemblies)
    • Designed for use with electric brakes only
  • Dimensions: 3" wide x 5" long x 1-1/2" tall
  • Mounting: between -20 degrees and 70 degrees in the vertical plane
  • 5-Year limited warranty


Proportional Braking

With a proportional brake controller, you can get heavy-duty emergency braking, general braking or slow-to-an-idle braking for your trailer automatically. The intensity with which your trailer brakes are activated and the rate at which they are applied are dependent on the deceleration of your tow vehicle. This means that, unlike time-delay controllers - which send the same amount of preset power to your trailer brakes every time - proportional controllers are able to adapt to every braking situation differently. So, if you slam on the brakes in your truck, your trailer brakes will activate with that same extreme intensity. And if you merely slow down as you approach a red light, your trailer will gradually brake in the same manner.


As long as the Voyager controller is mounted properly and is pointed in the direction of travel, it will sense - via an internal inertia sensor - how your tow vehicle brakes. This inertia-based sensor responds to the deceleration of your tow vehicle as you brake by signaling the controller to send out enough power to your trailer brakes so that they are activated with an intensity that matches. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.


Power and Sensitivity Adjustment

Getting the braking power you need for your application is simple with the Voyager. First, set up the controller as indicated in the instructions, making sure that the internal sensor is properly leveled. Then set the overall power by adjusting the power knob while you test out your rig. The power should be just enough to achieve maximum braking without locking up your trailer brakes.


Once you have the overall power set, you can fine-tune the power output by adjusting the sensitivity of the internal sensor. Use the level knob on the side of the Voyager to achieve your desired degree of intensity. Move the knob toward you (clockwise) to delay the power output, creating braking sensitivity that is ideal for lightweight setups. If you are towing a heavy load, you may want the trailer to brake more aggressively to prevent it from pushing your tow vehicle. To get more intense stopping action, turn the level knob away from you (counterclockwise).


LED Indicator

On the front of the Voyager there is an LED indicator that is designed to keep you aware of the braking action of your trailer. Typically, this light burns green to indicate that your trailer and tow vehicle are securely connected. When the light is green, only 5 milliamps are being drawn, thus minimizing drain on your vehicle's battery.


As you apply the brakes in your tow vehicle, the LED will change to red. This indicates that power is being sent to the trailer brakes. The light will also burn red whenever you activate the manual override lever.


During installation and setup, this light is used to ensure that the Voyager will be able to function correctly. Proper leveling of the internal sensor is crucial to the operation of this brake controller. When the sensor is level, the LED will change to a shade of orange.


Simple Installation

The Voyager is designed to be mounted in your cab at a vertical angle that is between -20 degrees and 70 degrees.


Correct Voyager mounting90-Degree Voyager mounting

Note: The Voyager must be mounted on a level horizontal (side-to-side) plane and must be lined up with the direction of travel for the internal sensor to function properly.


Once the controller is mounted, you must level the internal sensor. First, set the overall power to maximum using the knob on the side of the controller. Then, while pressing the tow vehicle's brake pedal, adjust the level knob on the other side of the brake controller (this is the same knob that is used to fine-tune the power output) until the LED monitor is a shade of orange.


Installation requires that you either purchase a custom wiring adapter designed to plug into the Voyager or that you hardwire the controller directly into your vehicle. To hardwire the Voyager, you must remove the plug at the end of the integrated wiring harness.


Installation Accessories

For easier installation, a vehicle-specific wiring adapter is available for most newer trucks and SUVs. One end of the custom adapter plugs into your vehicle, and the other end plugs into the controller - no hardwiring required.


Note: If a custom brake-control wiring adapter is not available for your vehicle, one of the following will be required:

20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications

30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications


See also etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.



9030 Tekonsha Voyager Electric Brake Control



California residents: click here



Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Honda
part number: 3070-P

Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.

Features:

  • Wiring adapter eases installation of your electric brake controller
  • Custom connector end plugs into the built-in port beneath the dash of your vehicle
  • Other end plugs into the back of your electric brake controller
    • Compatible time-delayed brake controllers: Draw-Tite Activator I (5100), Draw-Tite Activator II (5500), Draw-Tite Activator III (5520) and Tekonsha PowerTrac (39523)
    • Compatible proportional brake controllers: Tekonsha Prodigy (90185), Tekonsha P2 (90885), Tekonsha P3 (90195), Tekonsha Primus IQ (TK90160) and Tekonsha Voyager (39510)
  • Limited 1-year warranty


Installation of Tekonsha Brake Controller Adapter

This adapter plugs into the 4-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.


To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.


This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.



3070-P Tekonsha Brake Control Wiring Adapter with 2 Plugs



California residents: click here



Video of Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Tekonsha Brake Controller - Proportional Controller - 39510 Review

Today we are going to review part number 39510. This is the Tekonsha Voyager proportional brake controller. This brake controller will activate your trailer brakes in proportion to your vehicles braking action. It will automatically adjust the trailers braking based on deceleration of the towed vehicle. And it does activate immediately so there is no pausing like with your time delayed brake controllers.

It does have multiple mounting options, basically this would position within 90 degrees in a vertical plane, meaning this way. It will mount between a negative 20 which would be 20 degrees down, or a positive 70 in a vertical plane which would be up. So there is a 90 degree range. A minus 20 up to a positive 70. And horizontally, you do want this to be horizontal to the direction of travel. You do not want it to be turned that way or this way. And you can fine tune the adjustment braking power and aggressiveness right here with this knob. Right here is the LED monitor which will change color to alert you of the braking action of the trailer. The very front here you can see there is a built in slide bar manual override. This is used when you do need to in an emergency braking situation where you would need the brakes applied immediately.

Now on the back of this controller there is a plug that would plug into a harness. For an example here today we are going to use this pigtail harness, which actually has the plug on one end to fit the brake controller. And on the other end it just has the pigtail wires which will wire into your vehicle. This is a part #7894 that we do sell separately. Going to use that today to show you a demonstration. Now we also sell a plug in vehicle specific brake control wiring harness. We sell those separately. What that is, if your vehicle has a factory brake controller port, you can buy a harness for certain applications to reduce the installation time, and that harness would have the plug that would plug into the controller, and the other end instead of being the pigtails would have a plug that would match the factory brake controller port of your vehicle. So if that is available what you can do is check our fit guide online and that will tell you if your vehicle has a vehicle specific adapter available for your application.

Now this brake controller does come with the mounting bracket which mounts to the side right here, and the mounting hardware. It does come with a nice set of detailed instructions, and some pictures that will help you set up the brake controller. And again I mentioned we are going to give you a demonstration. I am going to take these pigtail wires and basically hook them up to a power source so we can show at least the light, how it changes colors. Once I get these all hooked up we will be ready to go. Ok, so we got them all hooked up to a power source. Here is the plug in. So basically we will just plug it in, turn on the power. Once you get power you will see a green light, that means it is connected. Now if the trailer was not connected, I will just unhook it here, you will see the light would not be on. So if the trailer is plugged in and connected you will see it gives a nice green light.

Basically the 1st thing you want to do is level this brake controller. And you will do that by taking this power knob and turning it all the way clockwise which will be full power. And then you would apply the brakes. And with holding the brake pedal you would go to this level adjustment knob over here and turn it. And you will see that it is green right now, and you will just start turning it to the back of the controller until you will see it will start turning to red. you can see how it changes to red, and what you want to do is then turn it back until you get a dim orange. Once you the dim orange that is your typical setting that you will want to start with. Then you can leave off the brakes. That will level the sensor on the inside. And then to adjust the power you have to do a test drive. what you will want to do is to go back to this power knob and put it at the 12 o'clock position, then go out and drive. Get it up to about 25 mph and apply the brakes. And then just adjust it from there. Application for this controller is trailers with up to four axles or eight brake assemblies. Now this is designed for use with electric brakes only. It will not work with electric over hydraulic. It does come with a five year limited warranty. That should do it for review on part number 39510 the Tekonsha Voyager proportional brake controller.



Customer Reviews

Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional - 39510

Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Honda - 3070-P

Average Customer Rating:  4.8 out of 5 stars   (556 Customer Reviews)

Proportional brake controller can be mounted within a 90-degree vertical range. LED monitor indicates braking action of trailer. Fine-tune power adjustment lets you set braking intensity to suit your towing needs. Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.

- 39510
by: Jo06/25/2019

Received all the products we ordered in less time than I thought it would be here. Thank you for such great service. 663198



- 39510
by: Jay10/07/2018

Brake controller ordered tues delivered thurs. Install took ten mins after watching video on E web site. These guys are great!!!!!! 572504



- 39510
by: JCS07/14/2016

I pull a small camper with a VW Touareg. The electronics in the T'reg don't play well with top of the line brake controllers. I spoke with the Tekonsha rep and he recommended the Voyager. The Voyager is a very simple controller, easy to install, and works well. I don't miss the fancy display. ICS 271698


Comments

Still works great. Pretty much set and forget.

JCS - 07/14/2017

26096

- 39510
by: Aaron02/15/2014

Installed easy and feels like its made well. I won't get a chance to use it for another week. The etrailer staff was very friendly and the shipping was fast. 116639


Comments

The brake controller has worked great over the last year. I have had no problems.

Aaron - 02/15/2015

9525

- 3070-P
by: Jeff H09/21/2017
2012 Honda Pilot

Perfect interface between the controller and the factory wiring. I'd have given it 5 stars if it were a wee bit longer - say 8 more inches. On my 2012 Pilot, I mounted the controller in the bin right below the radio because it just seemed in the way of my legs in the more normal position above the accelerator on the dash. The cable wasn't quite long enough for that and I ended up fabbing my own and put this one in the box for the next time. 434856



- 39510
by: Thomas08/30/2018

The controller works fine but it has developed a rattle on rough roads. It was a replacement for one I broke. 559720


Comments

The Voyager brake controller is an older design that uses a pendulum-style accelerometer, versus one thats solid state. This is the rattle youre hearing.

-- Mike L - 08/30/2018

42999

- 39510
by: Christopher10/19/2018

Works excellent for my camper 575885



- 39510
by: Eugene H08/14/2018

Got all hooked up,control is working as should,other issues on trailer.Seller told me had just installed new brakes,have to check them out as they are grabbing. Control is setting level,and straight,and checks out per instruction sheet. Very easy to install. 553766



- 39510
by: Dan C.09/10/2014

Awesome controller. We use them often our our equipment. Only problem we had this install, was locating the right wiring to tie into the brake circuit. New 2014 Chevy express van. Chevy only uses a 5 volt switched supply at the brake pedal. Ended up locating and tied into the brake light circuit for the 12 volts needed for controller to see the brakes are applied. 150511



- 3070-P
by: Tom10/02/2015
Honda Ridgeline

Just what the doctor ordered for the customers Honda Ridgeline. Unbilivably, though the truck was completely wired from under the dash from the factory since it was purchased new with the trailer package, the dealership was oblivious to the fact that a brake controller was needed and were dumbfounded on where to get one, or where the connector was located in order to install it. Found the controler on etrailer.com and the connector location on utube. 228914



- 39510
by: Walter Calloway/ Donna Calloway07/15/2017

The break controller was what I ordered but the wire harness that was sent with it did not have a wiring diagram so I could wire it to my truck correctly. I had to go to a YouTube video to get the correct information so I could wire the harness to my truck without hurting the controller or the vehicle. Question: Does your company not send a diagram with all of your harness? Customer should not have to go to a YouTube video to install the product. 406364


Comments

Hi Walter and Donna, since brake controller wiring harnesses are not universal, manufacturers do not provide wiring diagrams in their packages because they do not know how or if your specific vehicle is prepped for a brake controller. However, we do have a help article on brake controller wiring, and general trailer wiring. I have included links for your reference. If you have any other issues do not hesitate to contact our tech experts.

-- Sarah H - 07/17/2017

26233

- 3070-P
by: Hal J.05/02/2017
2014 Honda Ridgeline

Just bought the Tekonsha Primus IQ and installed it. Haven't used it yet, as I pick up my first travel trailer next week. Product is solid, packaged with ample, clear instructions, wiring and mounting hardware. Lower dash on my Honda Ridgeline slopes steeply so I fashioned an L-bracket from 14 ga. steel bar and secured to side of center stack (see photo). Nice and level. Wiring to my harness was a bear, just because of where my connector was buried; needed the YouTube videos. Price was much lower from etrailer than any RV dealer around here. Arrived in less than a week. Think I made a smart choice. If it works as advertised it will get a fifth star. 375303



- 3070-P
by: Peter T06/18/2018
2017 Honda Ridgeline

Hello, as requested I have attached some pics of the brake controller after installation on my 2017 Honda Ridgeline. I have a lease vehicle so I did not want to drill any holes in the vehicle to mount or run wires. So what I did was install the mount bracket upside down and place a strong commercial velcro patch to the brake controller mount and to the tray area that it is sitting on. Then I slipped the wire harness between the crack in the IP and the lower console and tucked it up behind the dash so it could not be seen. The velcro holds the brake controller quite secure. This way I can remove the controller and reuse in my next vehicle without leaving any permanent marks or holes to this one. Anyway , just thought I would share… As far as the controller. I am very happy with its operation and functions. 523633



- 3070-P
by: Holo11/30/2016
2017 Honda Ridgeline

I gave this a 4 star just because I haven't been able to hook up the trailer yet. The Primus IQ brake controller light is on so I'm assuming it will be fine. The harness arrived in good time. I was able to hook it up in my 2017 Honda Ridgeline in about 20 minutes. The longest part was finding the connection! It was above and left of the parking brake. A headlamp really helped. It's very tight in there so I could use only one hand and did a lot of it by feel. In the picture you need to follow the red wire to the connection. The brake controller I mounted on the plastic in front of my right knee. 321040


Comments

Update - Everything worked fine. We went on several trips with our trailer and no problems at all.

Holo - 11/30/2017

31345

- 39510
by: Greg M.07/30/2013

I have had several of these over the years. I currently have 3 controllers on different trucks. I pull 5 different trailers with completely different weights. The controller works really well. I definately recommend this controller. You level it on the left side, which allows for placement in alot of areas of the truck. When I am towing I can adjust the brakes with the dial on the right side. Obviously the brakes need to be lighter when the trailer is empty. Simply turn the dial back until the brakes don't lock up. When I get it loaded I turn the dial forward until I can feel the brakes take hold. The lever on the front lets me manually apply the trailer brakes. I use this in cases where I am going downhill and it is better to let the trailer slow me down. If I ever need another controller, this will be it. Great price also. 92292



- 3070-P
by: Mark F07/19/2017
2016 Honda Pilot

Just bought a Prodigy 3 and on my first trip with our light weight [email protected] clamshell with electric brakes pulled with a 2016 Honda Pilot...very satisfied. I installed a factory hitch and harness and the cable etrailor provided snapped right in. The trailer is under 2,000 lbs so I opted to bet the boost to zero. So far so good. The only issue is it seems to apply the brakes more firmly when going over rough pavement, otherwise the braking action is very smooth. I didn't want to mount the controller bracket permanently so I bent an angle plate into a U shape and pop riveted it so it would hang in the lower trim panel. 407957



- 3070-P
by: jim a06/09/2015
Honda Ridgeline

We have a Honda Ridgeline and this part plugged into the factory plug that was under the dash by the emergency brake petal switch. It was difficult to get to, but success was achieved. This was needed for our camper trailer. This made it easy, no hard wiring, just ordered the part for the Ridgeline and then plug and go. The brake controller plugged into the other end and now I am a happy camper. It worked, I blew a fuse while installing, must have touched something? No problem though, replaced it and was all was good. 202033


Comments

After one year, it is nice to not even think about it. I love products that work correctly. Gives one peace of mind. This is a great product. . thanks etrailer and Tekonsha for being wonderful companies. . . jim

jim a - 06/08/2016

18460

- 39510
by: Spencer O.10/17/2018

Everything worked out great! Install was very easy and does exactly what it's supposed to do. My ram didn't come with a brake controller from factory and this makes up for it. No complaints from me! 575045



- 39510
by: Kirk05/20/2018

Thus far it works great. I have a 2008 Toyota Sienna and use it for a tent trailer (pop up trailer). After researching and watching etrailer.com's video on installing a brake controller on a Sienna I found that the price was best here AND the kit to install it was without comparison. Really--I went to an auto parts store and tried to figure out what all I would need to create my own kit and it was exhausting. So great to follow what they have put together here. I took the trailer out after installing this brake controller and it was great. Braking felt like braking normally (with no trailer hooked up). I would recommend this product as well as the other parts and kits suggested by the youtube video. 511079



- 39510
by: John F06/29/2015

Very reasonable price and can be purchased with an adaptor designed specifically for my new Silverado 1500 truck! Very easy install! I recommend this item. 208077


Comments

Excellent easy install and works great!

John F - 06/28/2016

19000

- 39510
by: Joshua H01/18/2017

I loved this controller so much I put one in my other vehicle. For the price you can't beat it. Just don't forget you need the wiring harness item 7894 ($$) to go with it. Pros It is really easy to dial in how much brake you need. I dial it down when I get off the highway to prevent the trailer from pulling hard and increase it for higher speeds. Also you can pinch the lever the engage the trailer brakes without braking your vehicle to see just how much braking the trailer (only) is doing. Also there is an led indicator that turns from green to pink to red as more break is applied and serves as a good visual indicator. 333539



- 39510
by: Robert G07/15/2016

Completely plug and play installation and works flawlessly, very happy with this unit. I also ordered the exact harness for my 2005 f150 with tow package. Here are a couple of hints that may be helpful. My installation also required a 30 amp cartridge fuse to be installed in the fuse panel in location #105(electric trailer brakes) under the dash on the passenger side. I also installed a relay in location r05 (trailer tow battery charge) but I don't think this is needed for the controller to function. I still had the original trailer brake kit and it had the additional fuse panel instructions and the relay. The owners manual showed where the 30 amp fuse and relay plugs in. You cannot test this unit until a trailer with brakes is connected, ie the led will not light up until it senses a brake circuit. 272082



- 39510
by: Dale B10/18/2018

Works great easy to install took about 5 minutes to put it in 575598



- 39510
by: Kelly Gustafson09/01/2017

This is the second one that I own. Works great for what I need. Easy to use. 427714



- 39510
by: Byron10/04/2018

Easy to install. I have no complaints at all. It gets the trailer stopped without any issues. That’s all that matters. 571593



- 39510
by: Dave B.07/14/2013

Appears to work so far but too early to tell for a long term assessment. Liked that my vehicle had a ready plug under the dash so no wiring hassles were experienced. 89499


Comments

Thanks Patrick and I like it just fine although have used it only once. Is actuated by the use of the brake pedal and can be utilized manually by moving the lever horizontally to the right. Much of the credit should be given to the gal that took my call with the order. Originally was going the cheap route with no proportioning on the TBC and she indicated that I would be very disappointed if more money wasnt tendered for a proportioning TBC. It always helps when your sales staff has technical knowledge on the products.

Dave B - 07/16/2014

5686

- 39510
by: Steven09/30/2018

The product works great, no problems at all. I would recommend this product. Thanks, Steve 570354



- 39510
by: Patrick Magers05/06/2013

I installed this controller on a 2013 Jeep Grand Cherokee. Installation was easy (as I had also purchased the adapter cable for my Jeep), adjustment instructions were clear and the controller worked perfectly. 79126


Comments

Hi...am also looking at installing on my 2013 Jeep Grand Cherokee. Am in Australia....not sure what the adjuster cable is and whether it is something I should mention to my Auto Electrician. Are you able to clarify?

-- comment by: Terry B - 08/07/2013

1859

The adapter cable referenced is for plugging the brake controller into a port under the dash that Jeep provides on models with the factory towing package, in this case, it is part 3045-P. Please note this port will only be present and active on models equipped with a factory 7-Way trailer connector at the rear. These harnesses are also developed and designed for North American Market vehicles and if your Grand Cherokee was built for sale in Australia, it may not be compatible and could potentially damage the vehicle electrical system. In that case, it may be best to have the installer hard-wire in the brake controller and use an ETBC7 kit to complete the install. It would give the installer all the parts needed to add a 7-Way and wire the Voyager in.

-- Patrick B - 8/7/2013


- 39510
by: Richard P.03/01/2011

This installation is in a 2010 Ford F-150 Lariat The installation was very easy. It helps to have a 90 degree screwdriver to install the screws on the right side. The screws will install easier if you install them first, remove them and re-install after the bracket is installed on the vehicle. 8161



- 39510
by: Jeremiah09/15/2018

This is a good product it does the job very well but if you have different trailers I would recommend getting one that will remember a couple different settings. 565456


Comments

If you tow multiple trailers, I recommend a Tekonsha P3 part # 90195. The p3 lets you customize 5 storable settings for multiple trailers, varying loads or different drivers.

-- Heather A - 09/15/2018

43644

- 39510
by: Walter09/30/2018

Wonderful, haven't had any trouble. 570380



- 3070-P
by: dick10/15/2017

correct size and plugs for installation. 442898


Comments

I have been using both for a year and am very happy with them and the ease of install.

dick - 10/15/2018

44670

- 39510
by: Donald12/15/2017

I ordered the Tekonsha Voyager brake controller and harness for my truck from etrailer, received shipping confirmation within hours and the controller arrived in three days. I googled installation brake controller for my particular truck and etrailer had an excellent video which made it very easy to install. Setting the level and power were also easy as per Tekonsha’s instructions. All in all it was a good experience and the controller will be a good match for my trailer. A good product from a good company at an excellent price. 460310



- 39510
by: Steve E.08/26/2015

Seems perfect. I'll put 5000 miles on it over the next month. The three controls are easy to adjust without looking, though I'd prefer the side mounted knobs to stick out a little more, so you can grab them easier. 221933


Comments

They work great. I actually had the controller stolen out of the truck in Albuquerque this summer and replaced it with the same unit. \Unfortunately, I had to buy it quickly traveling so I paid more at a trailer supply store.At least the thieves didnt get the truck! A friend in the same parking lot wasnt as fortunate.

Steve E - 08/31/2016

20694

- 39510
by: Al W.09/02/2016

I chose the Tekonsha Voyager inertia activated brake controller because i wanted the inertia system rather than the time delay system but needed it at a reasonable price. I have not tried it yet but it checked out electrically. I have two minor issues: it did not come with a wiring adapter. Maybe none of them do but one is needed to make wiring easy. Fortunately, I ordered one at the same time. The other issue is that it requires the metal bracket for mounting but on my vehicle it sticks out too far and I bang my knee on it when I slide behind the wheel. I think I can use double backed tape for mounting and still have it positioned so the inertia part will work okay. 290689



- 3070-P
by: Debra09/14/2019

we love it. works as intended.easy to set up too. 703929



- 39510
by: jk09/09/2019

had this for a year now on my 2019 ram 1500 and it works perfectly We are pulling a 28 ft travel trailer with electric brakes .you can adjust the brake tension that works best for the trailer you are pulling. good product 699473



- 3070-P
by: Steve L09/04/2019

Product worked perfectly ... 697482



- 39510
by: Bryan08/31/2019

Not only did I purchase this connector, but the entire bundle as listed below. This is a great setup, works perfectly and looks great on the vehicle. Only seeing the hitch receiver, light harness, and break control hookup is clean and keeps near all the original ground clearance. Review the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" - 76227 Review the Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional - 39510 Review the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - C56040 698345



- 39510
by: Tom08/30/2019

easy hook up with adapter plug and worked great with my motorcycle trailer 695629



- 3070-P
by: Darrell08/29/2019

etrailer service is excellent. My brake controller was shipped and arrived promptly. I needed a bit of advice from the etrailer customer service group and they nailed it. Obviously, they know their products. If not, looks like they have a tech in the background that can help with those smaller details. Communication was excellent, as was follow-up on when my item shipped and even arrived. Excellent all around! I'm a very happy customer. 695578



- 3070-P
by: Craig08/20/2019
2012 Honda Pilot

About as easy as it gets to plug in and go. 691642



- 3070-P
by: Philip08/18/2019
2019 Honda Ridgeline

the right part always makes the job eas ier.. 690996



- 39510
by: Donald08/16/2019

This is a great little controller. Second one I've purchased plus recommended to a friend who's truck I occasionally borrow! Simple to install, set and adjust and it's reliable. I have a 6000lb trailer with brakes on all 4 wheels. You adjust this easily to the load you have on and your rig drives as if the trailer was not even there. You don't save money with a timed style brake unit, you just buy grief. etrailer has a great price for this unit and their delivery and service is outstanding. 690050



- 3070-P
by: Bob T.08/15/2019

Very good product, easy to install. Does what it is supposed to do. 688665



- 39510
by: Paul08/12/2019

Paid the extra $5.00 in freight and it was worth it. Received on the date expected in great packaging and installation was fairly straight forward. 688669



- 39510
by: Levi08/10/2019

For the price it’ll does the job fine but it protrudes a from under the dash more than I wish it did but can be modified in time. 683171



- 3070-P
by: Matthew08/08/2019

I bought a P3 Prodigy controller and the Honda wiring kit. Great customer service over the phone as I made my purchase. The person I spoke with was knowledgeable about the products and their applications. The wiring kit and controller arrived on the day they were promised and it took my mechanic about ten minutes to make the installation. I would definitely buy from etrailer again. 682233



- 39510
by: Lewis08/07/2019

Product was just as advertised, a plug and play inertia brake controller and adapter for my 2010 Ford F150. Had it installed in just minutes and it works great. Thank you. 682785



- 39510
by: Michael08/01/2019

Easy install and works great. 679273


Show More Reviews
562
562


Ask the Experts about this Brake Controller
Do you have a question about this Brake Controller?


  • Brake Controller Recommendation for 1999 Chevy Silverado
  • The correct brake controller harness for your 1999 Chevy Silverado is the part # 3025-P. Which for an economically priced brake controller that will still work great the best option is the Tekonsha Voyager part # 39510 as it is a proportional controller. Proportional means that it can sense the amount of braking your truck will be doing and will apply the same intensity to the trailer's brakes.
    view full answer...

  • Installation of Brake Controller on 2017 Chevy 3500 to Replace Factory Integrated Brake Controller
  • On your 2017 Chevy 3500 Duramax ltz, you can absolutely connect your Tekonsha Voyager Trailer Brake Controller # 39510 using the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers # 3016. This adapter plugs into the 4-pin connector in your vehicle's junction box. The box is located underneath the dash, to the left of the steering column, just above the carpeting. Because you have the integrated controller you will need to bypass it by cutting the blue wire on the # 3016
    view full answer...

  • Brake Controller Install Harness Location and Recommendation for 2017 Nissan Armada
  • If your 2017 Nissan Armada came with a factory 7-way at the rear of the vehicle you can use an install harness like part # 3050-P to install a Tekonsha controller like the P2 part # 90885. I attached a picture that shows where you'll find the port above the accelerator. If you do not have a 7-way you'll need the part # N40975 to install one.
    view full answer...

  • Installing Trailer Brake Controller on 2018 GMC Canyon
  • On the Tekonsha Prodigy P3 Brake Controller # 90195 (great choice) the black wire is for 12V power, the blue wire is for brake output to the 7-Way connector, the red wire is for brake switch on the vehicle, and the white wire is for ground. Based on my research the following connections will be made with the wires you found behind the kick panel of your GMC Canyon: Black wire on brake controller to red wire in vehicle Blue wire on brake controller to light blue wire on vehicle Red
    view full answer...

  • Wiring and Brake Controller Installation on a 2016 Chevy Express Van
  • You are definitely on the right track with parts # 118392, # ETBC7, # 39510, and # 20127 in your cart. I really only have one extra part that I believe you will need to add - part # ETBCXW which is extra wire for the # ETBC7. It gives you 10 extra feet of the wiring that you will need for the brake controller and 12V power for your 7-Way. Although the Prodigy P2 # 90885 is a great brake controller, the Voyager, part # 39510 is not a bad controller itself. The main great thing about it
    view full answer...

  • Installation of Brake Controller on 2015 Ford Transit T250 With Factory Tow Package
  • Since you already have the factory tow package in your 2015 Ford Transit T250, I recommend the Tekonsha Voyager # 39510 along with the harness # 20127 to give you your basic controller. This will need to be hardwired as your vehicle doesn't have the dash adapter. I recommend using a circuit tester like # PTW2993 to test wires for function before splicing. If there are no brake controller output wires and 12V power lined under your dash, then to hardwire your controller you will need
    view full answer...

  • What Gauge Wire is Used on Tekonsha Brake Controllers?
  • Tekonsha uses 10 & 12 gauge wire on their brake controllers. They use 10-gauge for the 12V and output and-12 gauge for the red and white.. We do not have replacement female-end connectors. We do offer the replacement male connectors for Tekonsha controllers, part # 20127, If you decide to install all new 7-way and brake controller wiring, I recommend our Universal Brake Controller Installation Kit, part # ETBC7. If you decide to go with a new controller, I've provided links to 2
    view full answer...

  • Troubleshooting Tekonsha Voyager # 39510 Showing Constant 12V Power on Blue wire
  • If you are getting 12V of constant power on your brake controller output wire then you need to cut the blue wire from your Voyager about 6" away from the controller and see if it still has constant 12V power. If it does then there is an issue with the wiring to the controller or your Adapter # 3050-P (if you have the factory tow package). If there isn't constant 12V power then there is an issue with the wire from your brake controller to your 7-Way. The only time that your brake controller
    view full answer...

  • Are Trailer Brake Controllers Vehicle-Specific
  • Trailer brake controllers such as the Tekonsha Voyager # 39510 are not vehicle-specific but the parts required to install one can be specific to a year/make/model vehicle. For instance, many pickups have a port under the dash to allow quick plug-in installation of the Voyager, such as wiring adapter # 22292 which works for Fords. To find the correct harness you can enter your vehicle info into our Fit Guide. You can also always hardwire a controller using our all-inclusive kit # ETBC7.
    view full answer...

  • Parts Needed to Install Brake Controller in 2017 Nissan Armada
  • You should be able to install the Tekonsha Voyager brake controller part # 39510 in your 2017 Nissan Armada with the install harness part # 3050-P and the 7-way install kit part # N40975 as our understanding is that every Armada in 2017 came wired for this setup. Other option is to hardwire the brake controller with first wiring in a 4-way like part # C59236 and then using the kit part # ETBC7 to adapt this 4-way to a 7-way and allow you to hardwire in the controller. Check out the
    view full answer...

  • Is There a Plug and Play Proportional Brake Controller for a 2004 Ford F-150?
  • If your 2004 Ford F-150 has a factory 7-way then there is one option for a Tekonsha proportional brake controller in the range you wanted, the Voyager # 39510, which you would plug into your truck with Wiring Adapter # 3035-P, as you can see in the attached video link. Should your F-150 have the factory 4-way instead you would need the same parts along with Vehicle Wiring Harness with 7-Way Trailer Connector # 118247; you can see how this installs in the other video link I added for you.
    view full answer...

  • Parts Needed to Install Brake Controller in 2001 Dodge Ram 1500 with Aftermarket 7-Way
  • You'll need the wiring kit part # 5506 to complete the wiring of your brake controller to your 2001 Dodge Ram 1500. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes are applied and none when not applied. This will be the circuit you will run the red wire to. Finally you will need to run a length of 10 gauge wire (part
    view full answer...

  • Where to Install Brake Controller on a 2015 Chevy Silverado 1500
  • The best place to mount a brake controller like the Tekonsha Voyager # 39510 is under the driver's side dash in a place so that it is within easy reach in the even that you need to activate the manual override. Technically it could be mounted to the floor but since that will be a little out of reach I recommend to the right of your dash under the steering wheel as you can see from the attached photo. This helps to keep it out of the way especially when getting in and out of your vehicle.
    view full answer...

  • How to Install a Brake Controller on a 2016 Jeep Cherokee
  • In order to install the Tekonsha Voyager Trailer Brake Controller part # 39510 on your 2016 Jeep Cherokee you will want to use the Brake Control Plug-In Harness part # 20127 if your Jeep did not come equipped with a factory trailer connector or the Tekonsha Custom Wiring Adapter part # 3014-P if your Jeep did come equipped with a factory trailer connector. If you do have the factory trailer connector then the harness plugs into a pre-wired connector under your dash near the emergency
    view full answer...

  • Brake Controller Connector Location on a 2004 Ford F-250
  • To connect your Tekonsha Voyager # 39510 to your 2004 Ford F-250 you will need the Adapter # 3035-P which connects to a plug under your driver side dash. Typically the OEM connector can be seen pretty easily but for your vehicle you actually have to take that panel off that is under your steering wheel. The connector will be on the right side after you take the panel off. I have attached a picture of this as well as a video of our team installing the Tekonsha Prodigy P3 # 90195 with
    view full answer...

  • Brake Controller Recommendation and Install for 2004 Chevy Avalanche 1500
  • Your 2004 Chevy Avalanche that has a factory 7-way at the rear of the vehicle is factory pre-wired for a brake controller but you will need a quick-install connector part # 3015-P to connect to the port of the junction box under the dash of your truck. For a brake controller I would recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses
    view full answer...

  • Troubleshooting Weak Trailer Brake Magnets with a Tekonsha Voyager Brake Controller
  • I can help you figure out what voltage should be coming down the brake output circuit on your trailer. If you have 10-12 inch brakes you should be getting 7.5-8.2 amps at 12 volts on the brake output circuit. If you have 7 inch brakes you should be getting 6.3-6.8 amps at 12 volts on the brake output circuit. If you are getting that voltage and the magnet is still not working, I would check for a worn magnet, a loose connection, or a bad ground. All of these could be causing the
    view full answer...

  • Troubleshooting No Power to Tekonsha Voyager Brake Controller 39510 in 2001 Dodge Ram 2500
  • It sounds like your 2001 Dodge Ram 2500 has a factory-installed 7-way and that your Voyager brake controller # 39510 is installed using wiring adapter # 3020-P, which connects under the dash. This 4-wire harness carries the +12V power to opeate the controller (black wire), the brake light switch signal that triggers it when you press the brake pedal (red wire), the output for the brakes that goes to the 7-way (blue wire) and the ground (white wire). You can use a circuit tester like
    view full answer...

  • Do Tekonsha Voyager and Prodigy Brake Controller Use the Same Wiring Adapter for Installation
  • Yes, you can easily replace the Tekonsha Voyager brake controller # 39510 in your 2007 Toyota Tacoma with the outstanding Prodigy P3 # 90195 simply by unplugging the old controller and plugging in the P3 using the same wiring adapter # 3040-P.
    view full answer...

  • Recommended Brake Controller and Wiring Harness for 2019 Honda Ridgeline
  • For your 2019 Honda Ridgeline, the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51392 is a confirmed fit. The installation will be under the dash, left of the steering column and near the emergency brake pedal. I recommend pairing this with the Curt Spectrum Trailer Brake Controller # C51170 for a really clean dash and easy function. I've attached a video to further assist.
    view full answer...

  • Where is Brake Controller Install Port on 2016 Honda Pilot
  • Yes, there is a port under the dash of your 2016 Honda Pilot for installing a brake controller like our best selling P3 part # 90195. All you need is the install harness part # 3070-P which is a confirmed fit. I attached an install video that shows this harness installing a brake controller in a similar Honda Pilot as yours as well. I also attached a picture that shows where you'll find the harness.
    view full answer...

  • Recommended Trailer Brake Controller for 2019 Honda Ridgeline Sport
  • I assume you are looking for a brake controller for a 2019 Honda Ridgeline Sport as that is all that pulls up in a google search. If that is what you are seeking I recommend the Tekonsha Prodigy P3 # 90195 which is a customer favorite because of the dependability and the ease of use with the LCD screen. For this you will use the wiring harness # 3070-P. I've attached a video of this on a 2017 model to assist. If you want a more factory brake controller appearance then I recommend
    view full answer...

  • Fuse location in Honda Pilot 2016 for Tekonsha 3070-P Brake Control Wiring Adapter for Honda
  • Your Tekonsha Prodigy P3 # 90195, can be installed using the # 3070-P if you have a factory tow package. It attaches with a simple clip connection to a plug under the dash of your vehicle near the parking brake. It isn't always easy to find in the midst of the wiring. Check out the installation video I've attached for you. There is not an extra fuse needed in this installation.
    view full answer...

  • Will Tekonsha Brake Controller Harness, # 3070-P, Fit 2005 Honda Odyssey With Prodigy Controller
  • The Tekonsha Brake Controller Wiring Harness, # 3070-P, is only for Honda Ridgeline and Honda Pilot with the factory tow package. To wire the Prodigy brake controller on your 2005 Honda Odyssey you will need to have a 4-Pole trailer connector on your vehicle. Then, you will have to hardwire the brake controller with the Brake Controller 7 & 4 Way Installation Kit, # ETBC7, to your vehicle. If you do not have a 4-Pole trailer connector on your vehicle, then you will need to install
    view full answer...

  • Wire Harness 3070-S Compared To 3070-P For 2017 Honda Ridgeline
  • The Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Honda # 3070-P is a confirmed fit for your 2017 Honda Ridgeline. The Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Pigtail - Honda # 3070-S is a confirmed fit for hardwiring any controller model to the factory connection. The dash P or the dash S is the manufacturers part number, so I don't know if it is significant to them or not, but it is just a part number to us. So, in reality, either product
    view full answer...

  • Color of Wires for Trailer Brake Controller Harness on a 2017 Honda Pilot
  • According to pages 462 and 463 of the online version of the owner's manual for your 2017 Honda Pilot the 4 wires for the trailer brake controller connector are black, brown, violet, and green so it sounds like you found the correct connector. If it matches up to the Tekonsha Plug-In Wiring Adapter # 3070-P then you can definitely be confident that you have the correct connector. If you don't already have a brake controller then I highly recommend the Prodigy P3 # 90195 because it has
    view full answer...

  • Troubleshooting Brake Controller that Won't Power On In 2015 Honda Pilot
  • It sounds like you are missing the fuse in your smaller, secondary under-hood fuse box that powers the brake controller. I checked in a manual for a 2012 Honda Pilot, and it was the number 14 fuse labeled Trailer E-Brake. It should be close if not identical in your 2015 model. There should be a diagram on the underside of the fuse box cover you can use to verify this.
    view full answer...

  • Brake Controller Wiring for a 2007 Honda Pilot
  • The Wiring Adapter, part # 3070-P will not work on the 2007 Honda Pilot. The 2007 Pilot does not have the provision for plugging in a brake controller under the dash. To install a brake controller on your Pilot, you will have to hardwire the controller, using our Brake Controller Installation Kit, part # ETBC7 (for a 7-way connector) or ETBC6 (for a 6-Way connector). The install kits contain everything necessary for installing your brake controller. If your Pilot does not already have
    view full answer...

  • Parts Needed to Install a Trailer Brake Controller on a 2005 Acura MDX
  • To install a brake controller on a 2005 Acura MDX you will need to hardwire it in using a 4-Way, # 118336, and installation kit # ETBC7. I have included some links to instructions and FAQs that will help with installation. For a brake controller I recommend the Tekonsha P2, # 90885. It is one of our most popular controllers because it is easy to set up and easy to use. I have linked instructions for it as well.
    view full answer...

  • Recommended Brake Controller And Wiring Harness For 2017 Acura MDX
  • There is no confirmed brake controller harness for the 2017 MDX so if a brake controller is installed it will have to be a hard-wire installation. If you do not have a 4-way trailer connector at the back of your MDX that is the first step that will need to be taken. I recommend part # 118628. This harness plugs into the location behind the driver side trim panel in the rear cargo area. You can see where it is located in the attached installation video I have provided. A tech tip for
    view full answer...

  • Brake Controller Installation on 2011 Honda Ridgeline
  • If your Ridgeline is equipped with the factory tow package, you can use the Tekonsha Wiring Adapter, part # 3070-P to connect a controller. The presence of the factory 7-way trailer connector on the rear bumper is a sure indication that your Ridgeline is equipped with the tow package. To install the controller, simply plug the larger end of the connector into the connector located under the dash. The connector can be found taped to another harness, to the left of the steering column
    view full answer...

  • Will Brake Controller Harness # 3070-P Work in 2012 Honda Pilot EX-L 2WD
  • If your Pilot came from the factory with the 7-way trailer connector at the rear bumper, it will have the connector under the dash that the # 3070-P would plug into. You would attach the controller to the underside of the dash within easy reach of the driver, plug one end of the wiring adapter into the connector under the dash and plug the other end into the back of the controller. Since it sounds as if you had to install a 4-pole wiring harness, the connector will not be present and
    view full answer...

  • Location of Factory Brake Controller Port on a 2011 Honda Ridgeline
  • If your 2011 Honda Ridgeline has the factory tow package with the factory 7-Way connector, then you will plug the Tekonsha Brake Controller Wiring Harness, part # 3070-P into the brake controller port which is located under the dashboard, to the left of the steering column. It will be taped to another wiring harness near the brake pedal. I am including a picture of the factory brake controller plug location under the dash on your 2011 Honda Ridgeline.
    view full answer...

  • What Brake Controller Install Harness is Needed for 2017 Honda Ridgeline
  • Yes, the brake controller install harness part # 3070-P that you referenced is also a fit for the 2017 Honda Ridgeline so you can use it to install in your new vehicle as well.
    view full answer...

  • Confirmation that the 3070-P Brake Controller Harness Does Fit 2016 Honda Pilot
  • There were some changes that threw us off for the 2016 Honda Pilot but we have personally confirmed here at etrailer that this harness, # 3070-P, does fit the 2016 Pilot. It turns out that the 2016 Acura MDX is the vehicle that this harness doesn't work with but it will work with the Pilot. The 3070-P is all you would need to install the Prodigy P2 part # 90885.
    view full answer...

  • Troubleshooting P2 Brake Controller 90885 Not Powering Up on a 2013 Honda Pilot
  • It sounds like you are missing the fuse in your smaller, secondary under-hood fuse box that powers the brake controller. I checked in a manual for a 2012 Honda Pilot, and it was the number 14 fuse labeled Trailer E-Brake. It should be close if not identical in your 2013 model. There should be a diagram on the underside of the fuse box cover you can use to verify this.
    view full answer...

  • No Power to Brake Controller on a 2019 Honda Ridgeline
  • The Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 3070-P that you referenced is currently listed as a fit for a 2006 - 2018 Honda Ridgeline. The 2019 model year has not yet been confirmed (August 2018) which might be why you are having issues. The pins may or may not have carried over to the next model year. The fuse that will supply power to a brake controller on a 2019 Honda Ridgeline is a 20 amp circuit in the number 3 position on the driver's side under hood
    view full answer...

  • Tekonsha Primus IQ Brake Controller # TK90160 Not Working on 2009 Honda Pilot With # 3070-P Harness
  • The Tekonsha Wiring Harness, part # 3070-P, with the Tekonsha Primus IQ Brake Controller, part # TK90160, is for use on a 2009 Honda Pilot with the OEM tow package and the factory 7-Way trailer connector on the rear of your vehicle. You will want to make sure that your vehicle has the factory OEM tow package. The wire colors on your Honda factory brake controller connector could be different than the standard black, red, blue and white colors on the # 3070-P connector. Each vehicle
    view full answer...

  • No Green Light on Tekonsha Voyager Brake Controller on 2010 Honda Pilot when Connected to Trailer
  • The green light on the Tekonsha Voyager Brake Controller, # 39510, indicates that the trailer is connected to your Honda Pilot, so it will not come on unless a trailer is connected. If the green light does not come on when the trailer is connected, then there are a few things that could be causing the green light to stay off. The first thing I would check is the trailer brake fuse in the secondary under hood fuse box. There should be a 20-amp fuse in fuse location # 14. If there is
    view full answer...

Info for these parts were:

Expert Research:
Michael L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Jeffrey L
Written by:
Lindsey S
Updated by:
Laura H
Updated by:
Alexander C
Updated by:
Isabelle B

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.




Product Experts Available Now!

Call 800-298-8924