1. Home
2. Truck Tool Box

Hello Jeremy, I sent that number over to lippert and they were not able to find anything. Can you please send me a picture of the sticker if it is still on there? Should have a S/N number and and RPO number, I included a picture of what the stickers…

Hello Chris, For your 2022 Grand Design Reflection 31MB 5th wheel with the MORryde CRE 3000 and wet bolt kit, the right crossmember brace is the MORryde X-Factor Crossmember #MR33WR. It helps stabilize your suspension, reduces stress by up to 94%,…

...2018 Ram 2500 64bed. I know all I need are some bolts, washers and lock-nuts, but is there a installation hardware kit for the UWS Truck Bed Chest - Wedge Series 11.8 cu-ft box...

The exact length of the Access tonneau cover part #A73FR is not available as we have requested this from them before but they have told us that as long as the tool box in the bed of your 2020 GMC Sierra 1500 6-1/2 ft bed is between 19 and 21 inches…

There isn't a set rule, but I'd recommend bolting the e-track into place. The distance between fasteners will depend on the nature and structure of the floor of your trailer. If the metal floor has a sturdy wood backing, I'd attach the e…

Hello Jacques, thanks for reaching out. Yes, you can put just one MORryde X-Factor Crossmember #MR33WR on the center hanger for starter. MORryde does recommend doing all 3 for optimal support, but it is perfectly acceptable to start with just one as…

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

We do have a MORryde X-Factor Crossmember that is compatible with the CRE. However, the #MR99ZR you were looking at only works with the LRE, RE, or TRE suspension systems. What you need instead is the #MR33WR. This is compatible with CRE, SRE, or…

...Can a tool box fit across the back of the truck with this ladder rack...

The Solera XL Power Awning Roller Assembly, #LCV000334966 that you linked to mounts using the Solera XL Power Awning Support Arms, #LC362243. The brand new arms you reference match those shown on the product page, then yes, the Solera XL Power Awning…

Hey Jacob, the drain plug of the UWS Matte Black 75-Gallon Steel-Aluminum Combo Transfer Tank #UWS39XR that you referenced is a 3/8 inch diameter bolt.

While I don't know what the dimensions on the Patriot Power Generator 1800, I can tell you that the TorkLift PowerArmor Single Locking Battery Box #TLA7720R is 17-3/4" Long x 8-3/16" Wide x 11-1/4" Tall. If your generator is under…

Hello Jeremy, I sent that number over to lippert and they were not able to find anything. Can you please send me a picture of the sticker if it is still on there? Should have a S/N number and and RPO number, I included a picture of what the stickers…

Hello Chris, For your 2022 Grand Design Reflection 31MB 5th wheel with the MORryde CRE 3000 and wet bolt kit, the right crossmember brace is the MORryde X-Factor Crossmember #MR33WR. It helps stabilize your suspension, reduces stress by up to 94%,…

...2018 Ram 2500 64bed. I know all I need are some bolts, washers and lock-nuts, but is there a installation hardware kit for the UWS Truck Bed Chest - Wedge Series 11.8 cu-ft box...

The exact length of the Access tonneau cover part #A73FR is not available as we have requested this from them before but they have told us that as long as the tool box in the bed of your 2020 GMC Sierra 1500 6-1/2 ft bed is between 19 and 21 inches…

There isn't a set rule, but I'd recommend bolting the e-track into place. The distance between fasteners will depend on the nature and structure of the floor of your trailer. If the metal floor has a sturdy wood backing, I'd attach the e…

Hello Jacques, thanks for reaching out. Yes, you can put just one MORryde X-Factor Crossmember #MR33WR on the center hanger for starter. MORryde does recommend doing all 3 for optimal support, but it is perfectly acceptable to start with just one as…

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

We do have a MORryde X-Factor Crossmember that is compatible with the CRE. However, the #MR99ZR you were looking at only works with the LRE, RE, or TRE suspension systems. What you need instead is the #MR33WR. This is compatible with CRE, SRE, or…

...Can a tool box fit across the back of the truck with this ladder rack...

The Solera XL Power Awning Roller Assembly, #LCV000334966 that you linked to mounts using the Solera XL Power Awning Support Arms, #LC362243. The brand new arms you reference match those shown on the product page, then yes, the Solera XL Power Awning…

Hey Jacob, the drain plug of the UWS Matte Black 75-Gallon Steel-Aluminum Combo Transfer Tank #UWS39XR that you referenced is a 3/8 inch diameter bolt.

While I don't know what the dimensions on the Patriot Power Generator 1800, I can tell you that the TorkLift PowerArmor Single Locking Battery Box #TLA7720R is 17-3/4" Long x 8-3/16" Wide x 11-1/4" Tall. If your generator is under…