1. Home
2. Trailer Parts
3. Trailer Wiring

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

...Do you have a Tow Ready T-1 Wiring Harness for a 2005 Honda Element that uses the existing jack near the spare tire? I see that there is a kit Tow Ready T1 vehicle wiring harness with a 4-pole flat...

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

Hi Eric, congratulations on the new camper! Starting with a hitch I recommend the etrailer #e75ZR. This is a Class III hitch with a 500 lb max tongue weight and a bolt-on installation. It has a concealed cross tube for a nice clean look and also…

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

Hello Luke. Yes, the Curt Hitch #C43RV will indeed fit the 2025 Hyundai Kona Electric. Curt confirms this to fit the EV and N Line models of the 2025 Kona.

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

Hey Bob, great question. It was about 7 degrees here in Missouri this morning, so I can relate to the cold. I do have a good solution for this too. What I would do is replace your current 7-way cord with the Curt Cold Weather 7-Way RV Style Connector…

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

...Do you have a Tow Ready T-1 Wiring Harness for a 2005 Honda Element that uses the existing jack near the spare tire? I see that there is a kit Tow Ready T1 vehicle wiring harness with a 4-pole flat...

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

Hi Eric, congratulations on the new camper! Starting with a hitch I recommend the etrailer #e75ZR. This is a Class III hitch with a 500 lb max tongue weight and a bolt-on installation. It has a concealed cross tube for a nice clean look and also…

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

Hello Luke. Yes, the Curt Hitch #C43RV will indeed fit the 2025 Hyundai Kona Electric. Curt confirms this to fit the EV and N Line models of the 2025 Kona.

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

Hey Bob, great question. It was about 7 degrees here in Missouri this morning, so I can relate to the cold. I do have a good solution for this too. What I would do is replace your current 7-way cord with the Curt Cold Weather 7-Way RV Style Connector…