Filter Results
Videos
for Trailer Hubs and Drums
Help Articles
for Trailer Hubs and Drums
Expert Answers
for Trailer Hubs and Drums
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
view full answer...To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…
view full answer...The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…
view full answer...Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…
view full answer...To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
view full answer...Yes, they have different widths. Each of the Flex guards you mentioned item #LC1346271, item #LC1346281, and item #LC1346291 are 50-1/2" long. However, the width of the single is 6", the double is 12", and the triple is 18".
view full answer...A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…
view full answer...Hi Hayden; that bolt pattern is really uncommon but I believe it can be found on some really old Airstream trailers. There are no modern replacements that will match. The best option is to replace the hub with one that has a common bolt pattern like…
view full answer...The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…
view full answer...I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…
view full answer...Hello Blake, thanks for reaching out. I did some digging and I was able to find a reference for the 92655 hub. This uses the 15123 inner bearing and 25580 outer bearing. It will be a 12" drum as well. This reference didn't tell me the bolt…
view full answer...Filter Results
4 on 4 Inch
$36.33 - $139.03
4 on 5 Inch
$91.91 - $91.91
5 on 4-3/4 Inch
$41.54 - $141.85
5 on 5 Inch
$40.95 - $152.12
5 on 4-1/2 Inch
$37.35 - $263.68
5 on 5-1/2 Inch
$45.01 - $147.57
5 Spoke Utility
$270.92 - $270.92
6 on 6 Inch
$85.46 - $102.05
6 on 5-1/2 Inch
$45.21 - $648.57
8 on 6-1/2 Inch
$70.34 - $757.23
8 on 8 Inch
$135.90 - $243.44
Trailer Hubs and Drums Parts or Accessories
