Tie Down Anchors - Trailer Tie-Down Anchors

A keen observation indeed, Brett. The mounting hole spacing on the Square D-Ring Tie-Down Anchor #ABS69FR is 3" horizontally and 3-1/4" vertically. I edited a picture for you to help illustrate.

We do not sell a complete kit but we do sell a backing plate that is compatible with the Square D-Ring Tie-Down Anchor item #ABS69FR. It is the Backing Plate for Brophy Recessed D-Ring Tie-Down Anchor item #BP05.

Hey Scott, thanks for reaching out. A 3-5/16" hole saw is what we recommend for installing the Square D-Ring Tie-Down Anchor #ABS69FR to the floor.

No, I am sorry we do not. I checked with Timbren's website and their 7,000 lbs item #TASR7KS01 and item #TASR7KS02 are the highest capacity ones you can get with a spindle. Did not see an 8,000 lbs capacity option. The Timbren Silent Ride…

Hey Mike, so the jack legs of the Trailer Valet Drill-Powered Stabilizer Jack #TV68FR do operate independently so you can lower them down to match the uneven ground the best it can. You should note these are not leveling jacks so you wouldn't…

I sure can Mark and thanks for the information! The Dexter 3,900 lb torsion axles use the same bearings as 3,500 lb axles. Which means the correct replacement bearing kit is the item #BK2-100 you were looking at. You'll need one set per hub. Your…

Hello David. All of the 2-1/4" or 2-1/2" long 9/16" wheel studs we offer have a knurl diameter of .68, such at the Kodiak Wheel Bolt #K916WB25. We do not have anything with a knurl size of .60 or .62. We do have some 1/2" studs…

I just spoke with my rep at Timbren and the Timbren Silent Ride Suspension for Single Axle Trailers w/ 3-1/2" Round Axles - 8,000 lbs item #T54FR has a total travel of 2 inches.

8,000 lbs is the correct rating for the Silent Ride Suspension: - Timbren Silent Ride Suspension for Single Axle Trailers w/ 3-1/2" Round Axles #T54FR This is unique in that it is for round, 3-1/2 inch diameter 8k axles, which are often Dexter…

No, the Timbren #T54FR cannot be used as a triple axle (or tandem axle) set up; for a triple axle set up for 8,000 lb axles the only option is the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Triple 8K, 3" Trailer Axles…

Hey Spencer, we have confirmed in the past that the Andersen Ultimate hitches can be used with offset balls like the Gen-Y part #GY43XR.

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

A keen observation indeed, Brett. The mounting hole spacing on the Square D-Ring Tie-Down Anchor #ABS69FR is 3" horizontally and 3-1/4" vertically. I edited a picture for you to help illustrate.

We do not sell a complete kit but we do sell a backing plate that is compatible with the Square D-Ring Tie-Down Anchor item #ABS69FR. It is the Backing Plate for Brophy Recessed D-Ring Tie-Down Anchor item #BP05.

Hey Scott, thanks for reaching out. A 3-5/16" hole saw is what we recommend for installing the Square D-Ring Tie-Down Anchor #ABS69FR to the floor.

No, I am sorry we do not. I checked with Timbren's website and their 7,000 lbs item #TASR7KS01 and item #TASR7KS02 are the highest capacity ones you can get with a spindle. Did not see an 8,000 lbs capacity option. The Timbren Silent Ride…

Hey Mike, so the jack legs of the Trailer Valet Drill-Powered Stabilizer Jack #TV68FR do operate independently so you can lower them down to match the uneven ground the best it can. You should note these are not leveling jacks so you wouldn't…

I sure can Mark and thanks for the information! The Dexter 3,900 lb torsion axles use the same bearings as 3,500 lb axles. Which means the correct replacement bearing kit is the item #BK2-100 you were looking at. You'll need one set per hub. Your…

Hello David. All of the 2-1/4" or 2-1/2" long 9/16" wheel studs we offer have a knurl diameter of .68, such at the Kodiak Wheel Bolt #K916WB25. We do not have anything with a knurl size of .60 or .62. We do have some 1/2" studs…

I just spoke with my rep at Timbren and the Timbren Silent Ride Suspension for Single Axle Trailers w/ 3-1/2" Round Axles - 8,000 lbs item #T54FR has a total travel of 2 inches.

8,000 lbs is the correct rating for the Silent Ride Suspension: - Timbren Silent Ride Suspension for Single Axle Trailers w/ 3-1/2" Round Axles #T54FR This is unique in that it is for round, 3-1/2 inch diameter 8k axles, which are often Dexter…

No, the Timbren #T54FR cannot be used as a triple axle (or tandem axle) set up; for a triple axle set up for 8,000 lb axles the only option is the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Triple 8K, 3" Trailer Axles…

Hey Spencer, we have confirmed in the past that the Andersen Ultimate hitches can be used with offset balls like the Gen-Y part #GY43XR.

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.