RV Waste Valves - Double Waste Valve - Manual

LaSalle Bristol doesn't make it so that you can replace much on their cable actuated waste valves besides just the handle so you would be better off just replacing the entire valve and cable system with Valterra's Black #TC372 and Gray…

Unfortunately LaSalle Bristol completely covers the connection point in plastic so the only way to gain access to gate inside the LaSalle Bristol Cable-Actuated RV Waste Valve #34466N4BB96GM would be to cut into the plastic for the cord and…

Pierre, the Bauer Products Camper Door Lock #BA65FR will work great as a replacement for your current TriMark door lock. This door lock will fit cutouts that are 5-1/4" wide and 4-1/2" tall, and can also be keyed alike to other Bauer locks,…

The gasket is the portion of the gate valve that's allowing waste water to leak through and not actually the gate. Both companies are using a rubber gasket that will eventually fail so it really comes down to the other features of the gate valve…

Remove the locknut from the cable housing assembly of the #34466N11AB96GMA. Feed the cable through the mounting bracket or hold in the wall of chassis. Feed the locknut back over the cable and fasten securely to the backside of the bracket or wall.…

Hey Mark, I looked up the specs of the spring you have now and found that it is a 24-3/4 inch long spring from eye center to eye center and for a 7k axle. So that means that the replacement spring part #EM28AJ that you referenced will work great as a…

A keen observation indeed, Brett. The mounting hole spacing on the Square D-Ring Tie-Down Anchor #ABS69FR is 3" horizontally and 3-1/4" vertically. I edited a picture for you to help illustrate.

It is completely within the realm of possibilities that the actuator has become disconnected from the gate internally causing the valve to not open. The Valterra Waste Valve Body for RV Black Water Tank w/ Coupler, Seals, and Hardware - 3"…

Plumbing parts are interchangeable on RV's just as long as the fittings are the correct size. I couldn't find that exact part number but I believe I have found the Valterra equivalent. If the Bristol valve you are talking about uses the…

Yes you can, Don. The MORryde U-Bolts for 5,200-lb to 7,000-lb Round Trailer Axles #MR66ZR which are 7 3/4" long, will work fine in place of the 9/16" ones, and will also work with your 7,000 lb axles.

Hello Tommy, I can help you determine the right black water tank valve, but we have no way of knowing which is a direct replacement part (we can't do anything with a VIN, unfortunately). The valve will either be a Spigot to Spigot or Spigot to…

I looked up the Bristol V33B2R and the correct replacement is the Bristol RV Waste Valve - Sewer Wye - Rotating - 3" and 1.5" Hubs to 3" Lug #34466N3AR which has the hub style fittings for the 3 inch and the 1.5 inch sections which…

LaSalle Bristol doesn't make it so that you can replace much on their cable actuated waste valves besides just the handle so you would be better off just replacing the entire valve and cable system with Valterra's Black #TC372 and Gray…

Unfortunately LaSalle Bristol completely covers the connection point in plastic so the only way to gain access to gate inside the LaSalle Bristol Cable-Actuated RV Waste Valve #34466N4BB96GM would be to cut into the plastic for the cord and…

Pierre, the Bauer Products Camper Door Lock #BA65FR will work great as a replacement for your current TriMark door lock. This door lock will fit cutouts that are 5-1/4" wide and 4-1/2" tall, and can also be keyed alike to other Bauer locks,…

The gasket is the portion of the gate valve that's allowing waste water to leak through and not actually the gate. Both companies are using a rubber gasket that will eventually fail so it really comes down to the other features of the gate valve…

Remove the locknut from the cable housing assembly of the #34466N11AB96GMA. Feed the cable through the mounting bracket or hold in the wall of chassis. Feed the locknut back over the cable and fasten securely to the backside of the bracket or wall.…

Hey Mark, I looked up the specs of the spring you have now and found that it is a 24-3/4 inch long spring from eye center to eye center and for a 7k axle. So that means that the replacement spring part #EM28AJ that you referenced will work great as a…

A keen observation indeed, Brett. The mounting hole spacing on the Square D-Ring Tie-Down Anchor #ABS69FR is 3" horizontally and 3-1/4" vertically. I edited a picture for you to help illustrate.

It is completely within the realm of possibilities that the actuator has become disconnected from the gate internally causing the valve to not open. The Valterra Waste Valve Body for RV Black Water Tank w/ Coupler, Seals, and Hardware - 3"…

Plumbing parts are interchangeable on RV's just as long as the fittings are the correct size. I couldn't find that exact part number but I believe I have found the Valterra equivalent. If the Bristol valve you are talking about uses the…

Yes you can, Don. The MORryde U-Bolts for 5,200-lb to 7,000-lb Round Trailer Axles #MR66ZR which are 7 3/4" long, will work fine in place of the 9/16" ones, and will also work with your 7,000 lb axles.

Hello Tommy, I can help you determine the right black water tank valve, but we have no way of knowing which is a direct replacement part (we can't do anything with a VIN, unfortunately). The valve will either be a Spigot to Spigot or Spigot to…

I looked up the Bristol V33B2R and the correct replacement is the Bristol RV Waste Valve - Sewer Wye - Rotating - 3" and 1.5" Hubs to 3" Lug #34466N3AR which has the hub style fittings for the 3 inch and the 1.5 inch sections which…