1. Trailer Parts
2. A-Frame Trailer Coupler
3. Weld-Onx

Based on your measurements it matches our Fulton 50-Degree A-Frame Coupler #FE443050303 which looks to be the same as what is on the 2024 Intech Sol Horizon from the videos I could find. So this would use either the EZ Latch #DM14793-81 or…

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I…

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with…

I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design then the Demco A-Frame Trailer Coupler #DM16680-52 will…

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts…

Hello Ryan. The #CA-5196-B Ram Sleeve Lock A-Frame Trailer Coupler and the Bulldog #BD028288 are fairly similar. They are both 50 degree a-frame couplers designed for a 2" ball and both are about 16" long overall. The main…

Yes, you can replace your weld-on coupler with a bolt-on. You'll just need to drill the holes. Then, if you wanted to go back to a weld-on later that would be fine too. Just to confirm you can check with the trailer's…

The Bulldog Heavy-Duty A-Frame Coupler, #BD44150WH301, does not come with the attachment bolts. I have attached two images showing the bolt pattern measurements and the bolt hole sizes. I would recommend using grade 8 bolts, but grade 5 is…

Unfortunately the Atwood coupler in your picture (appears to be part 88555) has been discontinued so there is not any latch kit or replacement parts available. At this point the only option we can offer is to replace the coupler entirely. The most…

All of the A-frame couplers we carry are for the standard 50 degree A-frames. What you could do, since your A-frame is a lower angle, is have some steel spacers welded on to get to 50 degrees and then use a weld-on coupler. I have linked the…

Hello Cale, thanks for getting in touch. We do offer some off-road tires but nothing in a 14". Our smallest off-road tire is the Kenda ST235/75R15 Radial Off-Road Trailer Tire #KE68JR. The ST235/75R15 tires are 9.3" wide…

Based on your measurements it matches our Fulton 50-Degree A-Frame Coupler #FE443050303 which looks to be the same as what is on the 2024 Intech Sol Horizon from the videos I could find. So this would use either the EZ Latch #DM14793-81 or…

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long.…

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come…

I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design then the Demco A-Frame Trailer Coupler #DM16680-52 will…

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts…

Hello Ryan. The #CA-5196-B Ram Sleeve Lock A-Frame Trailer Coupler and the Bulldog #BD028288 are fairly similar. They are both 50 degree a-frame couplers designed for a 2" ball and both are about 16" long overall.…

Yes, you can replace your weld-on coupler with a bolt-on. You'll just need to drill the holes. Then, if you wanted to go back to a weld-on later that would be fine too. Just to confirm you can check with the…

The Bulldog Heavy-Duty A-Frame Coupler, #BD44150WH301, does not come with the attachment bolts. I have attached two images showing the bolt pattern measurements and the bolt hole sizes. I would recommend using grade 8 bolts, but grade 5 is…

Unfortunately the Atwood coupler in your picture (appears to be part 88555) has been discontinued so there is not any latch kit or replacement parts available. At this point the only option we can offer is to replace the coupler entirely. The most…

All of the A-frame couplers we carry are for the standard 50 degree A-frames. What you could do, since your A-frame is a lower angle, is have some steel spacers welded on to get to 50 degrees and then use a weld-on coupler. I have linked the…

Hello Cale, thanks for getting in touch. We do offer some off-road tires but nothing in a 14". Our smallest off-road tire is the Kenda ST235/75R15 Radial Off-Road Trailer Tire #KE68JR. The ST235/75R15 tires are 9.3"…