1. Home
2. Trailer Parts
3. A-Frame Trailer Coupler
4. 2-5/16 Inch Ball Couplerx

Based on your measurements it matches our Fulton 50-Degree A-Frame Coupler #FE443050303 which looks to be the same as what is on the 2024 Intech Sol Horizon from the videos I could find. So this would use either the EZ Latch #DM14793-81 or…

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design then the Demco A-Frame Trailer Coupler #DM16680-52 will fit…

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

Hello Bill, thanks for reaching out. I cannot say I have ever heard a complaint about a Demco Ez-Latch Coupler like part #DM37ZR failing and coming disconnected. I ran your question by a group of my associates here and not one of them could recall…

...To install the Demco A-Frame Trailer Coupler # DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing...

...and disconnect from your trailer. For a coupler that fits a 2 inch ball use # DM14793-52 and for a 2-5/16 inch ball use # DM16680-52....

...Based on my research the Shelby 5101 is an A-frame coupler with a 2" ball and 5,000 lb capacity. We have exactly that with the A-Frame Coupler # CA5100B, which has a trigger latch and has a black...

...of the dimensions below so you can see if it would work for you. When installing the Demco 50-Degree A-Frame Trailer Coupler # DM13205-95, you will want to use 3/8 inch grade 5 bolts, that are approximately 1-1/2...

...of the coupler to mount to your trailer. I spoke with my contact for Bulldog and he said you will need 10 bolts 3/8 inch bolts for the smaller diameter holes and two 1/2 inch bolts for the larger diameter holes...

Based on your measurements it matches our Fulton 50-Degree A-Frame Coupler #FE443050303 which looks to be the same as what is on the 2024 Intech Sol Horizon from the videos I could find. So this would use either the EZ Latch #DM14793-81 or…

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design then the Demco A-Frame Trailer Coupler #DM16680-52 will fit…

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

Hello Bill, thanks for reaching out. I cannot say I have ever heard a complaint about a Demco Ez-Latch Coupler like part #DM37ZR failing and coming disconnected. I ran your question by a group of my associates here and not one of them could recall…

...To install the Demco A-Frame Trailer Coupler # DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing...

...and disconnect from your trailer. For a coupler that fits a 2 inch ball use # DM14793-52 and for a 2-5/16 inch ball use # DM16680-52....

...Based on my research the Shelby 5101 is an A-frame coupler with a 2" ball and 5,000 lb capacity. We have exactly that with the A-Frame Coupler # CA5100B, which has a trigger latch and has a black...

...of the dimensions below so you can see if it would work for you. When installing the Demco 50-Degree A-Frame Trailer Coupler # DM13205-95, you will want to use 3/8 inch grade 5 bolts, that are approximately 1-1/2...

...of the coupler to mount to your trailer. I spoke with my contact for Bulldog and he said you will need 10 bolts 3/8 inch bolts for the smaller diameter holes and two 1/2 inch bolts for the larger diameter holes...