Most Popular Dark Tint for Wagon

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

Good fit after a finnicky installation. The front guards do not use an adhesive to install, just pressure, so time will tell how they hold up, but initial impressions are good.

Window deflectors look and perform great! All vehicles I own will have these essential deflectors on them!

This is the 3rd time that I have ordered from E-Trailer. Everything was delivered as promised, actually earlier than Promised.I will always use E-Trailer for any future Purchases for my vehicles.They keep you informed through out the whole purchase, from start of transaction to help with the installation. Keep up the good work !! Thanks Jay K

These were hard to find,but fit perfectly!

I made a mistake when I ordered these thinking they were the stick on type. Not the intrack type. I was upset but wanted them for an upcoming road trip. Although they're not terrible I've had issues with the window catching on the plastic and the safety feature not allowing the window to close due to the resistance. These are the reasons I wanted the stick on type. Only advantage here is that the in track type are not permanent. I also found the rear window pieces seem to bow out quite a bit which looks silly.

all products perform as expected. had a problem with defect but was serviced and replaced promptly. wonderful experience.

Instructions for rear vents not accurate at all. Finally had to put them on the way I thought will work. Time will tell if they stay on.

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

A bit tricky to install because they are such a tight fit, so that is a good and a bad thing. One year later though, what I put in hasn't come out and works brilliantly!

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

Unfortunately the rain Guards don't work properly on my vehicle, the minute they sense the rain Guards the window retracts in the open position,and I can't close my windows. I will be looking to return these if I can't fix the issue ,or if possible return for a rain guard that has a self adhesive that sticks on the outside of the window trim. Thanks S

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

rain guards fit perfect and look good. cant send pics because my windows are tinted and the guards dont show up in the pics. now the bad, shipping was good until UPS gave it to the post office . post office said they tried to deliver it on sunday but they couldnt get into the building. i checked the security camera and no post office vehicle was here at the time they said they were here. also the doors do not lock until 8 pm.

I love them still new they are easy to install also take it to the car wash every day and believe me no damage at all and it handles rain so its amazing how strong they are and flexibility when you install them.

Click to Enlarge

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

The WeatherTech Sunroof Wind Deflector works perfectly on my Honda Pilot.

I have a 2015 Toyota Rav4 it works perfect. Since my speaker phone is right next to the sunroof there was a bunch of noise if the sunroof was open. This product looks good fits perfect and really helps with the noise level. Love it!

First bad experience with a WeatherTech product. Do not recommend for 2010-2014 Ford Expedition or similar models. I see 4 flaws. 3 of 4 pieces cracked at the corner even when I tried to be as gentle as possible in incrementally raising windows once installed. It seems to be just a few millimeters too oversized. Second, Rear windows will not raise all the way back in place due to thickness of plastic, it stops. You have to push windshield up while holding the switch. I was worried that this force would damage the window tint due to excess friction and it may push the rubber out to the point it would be damaged if I took them off months or years later. Third, and arguably the most important. Too much wind noise. The Ford Expedition is very quiet for an SUV. I tried these for close to a week and I had to take them off. It sounded like gusty wind noise even when there was no wind other then the vehicle going through the air. I removed them and the SUV was quiet again. Four, It isn't optically correct. Hard to see in the photo, but when looking at the area between the A pillar and side mirror, it's wavy and distracting. Also makes the A pillar appear much larger when it's darker outside due to the tint. So even though they look nice, and you can crack your windows in the rain if your car is sitting still or you never exceed 50 mph... I wasn't able to get comfortable with the above issues. I can't return them since I installed them and tried them. But hopefully someone else can benefit from this.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It’s still early. I did the upgrade while in a walking boot (cannot drive) due to an Achilles rupture. So I can only comment on the install, which was much easier on the back windows. The front windows were a little awkward but eventually went in. I don’t like the ‘clunk’ as the window closes in the last inch or so. The window comes in contact with the deflector and clunks. I hope the plastic heats / cools and reforms as it sits over the next few days. Otherwise I like the look and finish, it’s just the fit which I’m not completely convinced off yet.

Fit was great but both back visors are damaged. Driver side has a big crack, passenger side has several small cracks. Front visors are great and easy install. Look really sleek!!

2017 Ram Bighorn. Excellent product and easy to install.

Click to Enlarge

Looks good and easy to install, just watch the installation videos.

Window vent shields went on quick and look great.

Click to Enlarge