Best Toyota Avalon Bike Racks

Excellent and prompt customer service! When I first ordered my product it wasn’t in stock— staff were quick to let me know and offered me comparable products. I ended up waiting for my original order and shipping quick and they stayed in touch with ideas! Thule: The instructions could be a little more detailed. I ended up watching YouTube videos to help me instal. Overall it was easy, and this was the first rack I’ve ever installed and I did it by myself! I was surprised to learn the bike rack is in no way secured inside your vehicle, so.. I store it in my garage when it’s on.

Click to Enlarge

Positive: The product is well thought out and works for a wide range of automotive vehicles. It comes with interesting dampers that i think work. Instructions seem to be translated from another language, but are quite good, accompanying pictures make installation straightforward. A test drive over speed bumps shows that the rack will support the bike for all travel needs. It can be disassembled , collapsed and stored in the trunk. Downside: The rack is made for the classic triangular shaped frame: horizontal cross bar, "male" bike. For bikes without the horizontal bar, mounting is a little less satisfactory. Such a bike can only be mounted on the outside mounts. Cannot use the damper on one side. Picture shows the mounting. as to a design solution, maybe brackets could be replaced with smaller profile, some adjustability? however, as it is, vibration control is good and adjustability with smaller profile would have vibration concerns.

Click to Enlarge

First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installation was straightforward. The rack sits high up on my 2016 Subaru Forester so lifting bikes onto the rack requires effort. Getting 3 mountain bikes on the rack was a bit tricky. When loaded rack was secure and stable.

Seems like a sturdy, reliable product so far. Components are solid and well put together. Fits great and carries well on my 2014 Corolla. Excellent value considering the price tag on other racks out there. And the prompt delivery was great!

Click to Enlarge

Seemingly well-constructed and supported bike rack. It fits my 2018 Toyota Camry SE just fine and I haven't had any issues with sway or even feeling my bike while driving. I've only carried one bike on it and have used it a limited number of times, so I cannot speak on durability and longevity. Although you shouldn't open your trunk while the rack is attached, I have been able to do so with no issue (without the bike attached).

While getting a bike rack for a sports car isn't ideal, I really wanted to transfer my bike with my own car instead of borrowing my friend's pickup truck. After hours of trying to find a bike rack that would be good for my 07 Mustang, I decided to give this one a try and I gotta say, it has been pretty good so far. It fits very well over the factory spoiler. One of my biggest concerns I was worried about when ordering a rack for my Mustang was ruining the paint, but the feet on the legs haven't left one scratch. I have used this to transfer my bike at freeway speeds (up to 80 mph) on car rides that typically last an hour and my bike was perfectly secure throughout each ride. For extra security, I wrapped both bike wheels with a ratchet strap so the wheels and pedals wouldn't shift in transit. So far, I am very pleased with this bike rack for the price and quality. I would highly recommend this if you want a rack that is affordable and durable.

Click to Enlarge

The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.

Click to Enlarge

Hitch pin broke before I got it. Looks like a poor design for the locking pin, they might want to consider a different design. I got a 3/8 shear pin from Home Depot to replace and it works great. Bike rack is great!

Click to Enlarge

Draw-tite Sportframe Trailer Hitch Receiver Class I - 1-1/4 Swagman Trailhead 3 Bike Rack - Tilting The Draw-tite Sportframe class 1 trailer hitch and Swagman Trailhead 3 bike rack were ordered for a 2017 Honda Fit. The online order and shipping went just as expected. The trailer hitch and bike rack are very heavy duty. I recommend watching the trailer hitch install video before installing, whereas the video is very helpful. The bike rack has triangles that you can rotate to find the best fit for your bicycle's frame. The rubber straps are thick and secure the bicycles when you pull them tight. This bike rack will stay on the vehicle for 6 months each year. The tilt feature and folding arm feature are must haves for a smaller hatchback. I am pleased with this purchase, it appears to be good quality and good value.

Click to Enlarge

My previous bike rack was a hitch mounted Yakima. It was sturdy but not well suited for my low Subaru Impreza. It stuck out too far and hung too low so that I had to inch my way down the driveway or over speed bumps for fear of it bottoming out. A roof rack or a rear window mounted rack was not suitable since I wanted to be able to also carry two kayaks. First, I tried to modify my rack by shortening the part that sticks out of the hitch. I tried to saw off about 6 inches so it wouldn't stick out so far but the steel was much too hard. I ended up ruining several metal-cutting blades on my power saw before I gave up. I looked for other rack options. There weren't many out there. But eventually, I found something that met my needs. I purchased the "Swagman Trailhead 3 Bike Fold Down Bicycle Hitch Rack" in 2013 from eTrailer.com. The part that enters the hitch curves up to increase clearance from the ground. It is sturdy and sticks out far enough so I can still open my trunk hatch without having to lower the main vertical bar on the hitch (though I could if I wanted to). It isn't often I am really excited about a piece of gear but this hitch rack has made me worry-free when I transport my bicycle(s) via car. The only thing I don't like is that it is advertised as being a 3 bike carrier but it only fits 2 hybrid bikes. Maybe it will fit 3 skinny racing bikes but for the average rider, don't expect to fit on more than 2. But my experience is that is the case for all bicycle racks.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

After doing extensive research before buying my first ever bike rack, I chose the Kuat Sherpa 2.0 platform rack. I considered trunk mounted, hanging and platform racks before settling on a platform rack. I like the stability, the ease of loading and unloading and very importantly, the absence of contact with the frame of my bike. My bike has a beautiful paint job that I want to preserve. I looked at lots of racks online and at a bike shop and opted for the Kuat Sherpa 2.0 because of the excellent engineering, including the design of the packaging that becomes a work bench for assembling the rack, the relatively light weight (32 pounds), the inclusion of a hitch lock and a bike lock, the stability of the platform, even with a 1.25" connection and a class I hitch, and the ease of operation. Additionally, the overall appearance of the rack suggests high quality. Time will tell how well it ages but I'm pretty confident that I'll be pleased with it. I was very fortunate to find a used, like new Kuat via Etrailer at a meaningful discount that still qualified for the manufacturer's warranty! Thank you Etrailer! A tip to pass along that was shared with me, U-Haul is an excellent source for buying and installing hitches to accommodate bike racks - very attractive pricing, high quality installation and a super unlimited lifetime warranty. Can't wait for Spring and the chance to transport my bike to inviting riding venues!! PS The hitch and bike rack work very well with my 2011 Honda Accord Coupe, EXL V6 model that remains in excellent condition.

I have been in search of a really good hitch mounted bike rack for some time. I did a lot of research and settled on the Kuat Sherpa 2.0. But before I ordered it, I called etrailer.com. I spoke with Lori B. who answered all my questions about this rack and made my shopping experience quick and informative. This rack is so well constructed and beautifully finished, rugged and very easy to use. On our first trip out, my 12 year old son was able to quickly and easily remove his bike with no help. The rack tilts down with little effort making access to the back of our station wagon a breeze. I would recommend this rack to anyone looking for a well built easy to use 2 bike rack. My neighbor told me about etrailer.com and it was great advice. I will be ordering from etrailer.com again. Their service and selection are amazing and they actually have people answering the phone who know their products.

Click to Enlarge

I was looking for a light weight bike rack for my 2015 Honda Accord. Your videos stated that the Kuat Beta was light and easy to install. You were right. I opened the box, read the instructions, and had it installed in about 10 minutes. I don't use a rack lock. It is so easy to pop on and off the hitch that I keep the rack in my car trunk.

Click to Enlarge

We've been using this bike rack with a 1.25" Draw-Tite receiver hitch (also purchased from etrailer) on a 2012 Prius C for a month with no problems. As shown on the pictures, it fits two bikes very well, even one with a baby carrier. I chose this model based on recommendations from etrailer that it can be easily detached from the car without tools. True to their word, it is very easily detachable from the hitch and folds up nicely to fit in your garage/closet/storage area. Basically, it uses a hand tightened ball bearing mechanism to secure itself into the hitch receiver, and then uses a 3/8" hand locked pin as a safety device. You can install and de-install this rack in just a few minutes. During driving, there is little noticeable vibration from this rack, even on rougher roads or speed bumps. The only downside is that the holes on the receiver hitch do not align perfectly with the holes on the bike rack (see picture). I believe a few other reviewers also noted this issue. There is enough room to fit the safety pin, but not quite enough to fit a 1/2" hitch lock. I called Kuat to ask them about this and the rep told me that not all hitches will line up with this rack. Kuat, coincidentally(?), sells a hitch lock that is also 3/8" (same size as the safety pin) and still fits.

Click to Enlarge

Click to Enlarge

Click to Enlarge

It was obvious that we received a product that was returned by someone else when the box was overly taped shut, a support collar was broken, and most of the pieces were out of their ripped plastic bags. However, it was a great price to hold 5, 26" and/or 27" Trek bikes. I used a piece of the broken collar and went ahead and assembled the rack. Due to the weight of the 5 bikes it did not wobble that much when driving, as one of the bike tires was up against my car. I can only imagine that if we received an untampered product that this review would have been 5 stars. The picture is a little hard to see, but there are 5 Trek bikes on the rack on my 2020 Toyota Seinna.

Click to Enlarge

We received a damaged box, damaged items, no instructions, the nuts and bolts are completely stripped and not inside a bag. This was obviously used, returned, not checked for quality and sent out. We are extremely upset.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Fits perfectly on our Lexus CT200h. Only on the old LS400, the side straps have to be fastened to the wheel arch edge, since the upper trunklid gap is to narrow for inserting the strap hooks. Mounting of two bikes is (with some routine) quickly done, and they stay safe even for longer and faster routes. For transporting three (mountain) bikes, though, the design doesn't seem big and robust enough. Nevertheless, the price-benefit-fun ratios are way better than reasonable.

Click to Enlarge

We are very pleased with the quality and ease of use for our like-new purchase. From the online shopping experience with etrailer.com through multiple outings already, this bike carrier more than meets our needs. Thank you!

I think this is a simple and efficient rack, but it is not for everyone. Because it is a frame clamp design, you should not mount Carbon Fiber frames or thin walled aluminum frames for risk of frame damage. Thich aluminum and steel frames should not have a problem. My heavy fat bike fits just fine if it's the only bike on the rack. 2 regular mountain bikes will fit in opposite directions. This rack will never realistically hold 3 mountain bikes. (maybe 3 road bikes) I removed one of the clamps, easy to do, makes a cleaner setup. Bikes with small triangles (smaller frames and certain full suspension) will be difficult to mount due to the locking/clamping mechanism size trying to fit through the frame and made worse with bottle holders. I changed out the bolts at the hitch side to make it a rigid rack. There is no need for me to pivot this rack and now has one less thing to go wrong. The threaded locking bolt makes this hitch rock solid with no clunking noises while transporting. The BIG advantage of this rack is storage. It fits behind my seat and is invisible to the passing eye and can be installed or removed in a few seconds.

After a year of owning this bike rack, I must report that I have no problems with it to date. All works as advertised. I have a Hyundai Ioniq and it was difficult to mount any rack, and I had to go with the 1 1/4"hitch. It's been great so far, steady and not shaking on the highway. Mostly use 2 bikes, although a couple times I have used 3.

The Malone rack adjusts to fit my 2017 Trax really snugly and securely. Once we learned how to configure the bikes for best fit, everything traveled without movement. The only downside is that this system seems designed for narrow road bikes rather than the mountain and hybrid bikes we own. Although the anti-sway cradles are sufficiently wide for mountain tires, the close proximity of the individual bike setups sometimes cause a strap to pull loose during travel, so we keep the bikes cabled to the rack frame. We are able to make it work. For narrower bikes, I would recommend this rack without reservation.

Works great! We keep it set up to one position because it's used on my car only. I'm glad we bought the lock feature because we can just leave the rack on at the trail site. This was a great purchase. I'm impressed that you follow up on your product. I recall your staff was quite helpful in making sure I purchased the correct item for my car and set it up correctly. No recent pictures of the carrier but I do have one of myself as "happy camper" on the Fox River Trail which was doable because of the carrier purchase!!

Click to Enlarge