# 1
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 2
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
My son and I finished putting on both hitches front and rear, Rear was very easy after we cleaned out the rust. The front was a little bit of a chore because we did it with car ramps and it took some maneuvering to get the bolts tightened down. But we got it done and it looks great on my Liberty. Pictures above. I would definitely recommend you guys, the instructions were very helpful. Will do a review tomorrow gotta watch the games now.
Very well made and really fast delivery, excellent transaction and the people at trailer put a lot of effort into seeing you get your order
# 4
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I wanted a front mounted hitch receiver for my 2008 Jeep Grand Cherokee to allow me to mount a surf rod and cooler carrier. The Jeep is already low hung in the front so I was concerned about the hitch receiver causing me to loose some clearance if it hung too low beneath the air dam. The installation instructions, reviews and pictures I found didn't seem to assure me either way. In my case the receiver ended up only about 3/8" below the air dam which I had cut an opening in as directed in the instructions. This was satisfactory for my needs. The instructions were mostly clear and easy to follow but I found that additional trimming of the air dam was required due to interference with the front legs of the hitch receiver. The area trimmed is not visible but this added a couple of hours to the installation while I checked and re-checked to be certain trimming was required. I found a "copping saw" useful to trim the air dam. One nit regarding the instructions is that there were "Options" mentioned like "enlarging" the pre-existing holes" and using alternate "fish wire" techniques, but there was no explanation of why you might choose to use the options. The manufacture has some useful videos on their web site but the "technical support phone number" listed on the instructions (800-798-0813) did not work for me but failed in various ways and resulted in various error messages/results. The hitch receiver seems well made and very sturdy and arrived in just a couple of days. Originally I was hoping to find a receiver that mounted so as to be in the opening above the air dam giving it more height and not affecting ground clearance. That was not available but this works almost as well and I have an adapter that will permit additional height for the mounting of the surf rod and cooler carrier. This receiver will also provide a "recovery point of attachment" for my Jeep.
The order was delivered and the process was great throughout the whole order.
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I ordered this unit after sending one back from a different supplier ,the previous one said it fit my Ranger, well after getting it and checking installation video`s it needed to be cut up and fafbricated, no thanks. The Draw tight from E-trailer fit great,delivery was prompt even with a major snowstorm ,the only hic-cup was I didn`t take off my front bumper,due to a brush guard we welded on years ago but even without taking off the bumper I was able to get it on , heck I didn`t even jack up the truck. A little trim on the bumper trim and some help from my motorcycle jack easy to do , took about an hour and a half looks good , fit great, now its time to attach the snow plow and get my driveway clear.I am also ordering the air bag spring helpers for my little truck and will see how that goes too, thanks to the staff at E-trailer, I`ll be ordering from you again.
This is a great addition to my old square body Explorer Sport, the closest thing I can afford to a square body Bronco. Great for moving trailers around the yard or put a hitch mounted bike rack up front and tow your boat or camper behind. Best part was no drilling direct fit and in stock at etrailer!
What our customers are saying:
"WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!"