# 1
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
A good install! A bit of trimming for my application , but the bolt holes lined up perfectly. This front hitch was not specifically for a Lexus GX 460 but I decided to try it. There is a small area of lower bumper plastic that had to be trimmed. The hitch was pushing up against it before it was high enough to be in place. Upon trimming that area, it went in perfectly. If trimming the lower plastic is not for you, probably best to pass. However for my use, it works well. It is a stout piece, very strong. I added a pic with a red line to show where the trim needs to be.
Installed on my 2012 Lexus GX460. Perfect fit once I cut the center section of the lower plastic area for it to fit. Also had to trim the bottom splash guard and bend in the L brackets that hold it on. Took me about 2 hours. Very happy with the outcome. Now can mount snow blade for the driveway clearing…or any other hitch items.
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
How it was received; either is was mail destroyed or UPS did this in the process. No telling what parts are missing, waiting for UPS to come pick this and E-Trailer to send out replacement. I thought these product would be packaged better from the factory for shipping resilience.
Of the many hitch receivers I have purchased, the front mounted ones have never failed to surprise me of their usefulness! From bike racks, to carrier for coolers, to my chainsaws, gas and oil, they make it work. Recently while cutting wood for a hunting lease engagement, I put a second ball on the front and used it to drive a 16' trailer up a hill to get the wood where it was needed for offloading. Backing it up had resulting in damaged trucks, trailers and numerous attempts. Using the front hitch it was a one and done deal! Love it! I have even used it to pull trees over when felling. I don't have enough fingers and toes to count the uses! If you have ever thought about it, just stop and order! You won't regret it!
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitched arrived three days early and I was able to install it in less than 2 hrs with a little help from my wife and a floor jack. Perfect fit!! No shimms necessary Vwrry happy.
The hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.
# 6
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Got this front hitch for my Nissan Xterra so I can push my boat into my garage. Access to the garage is in an alley and the only way to get the boat into the garage is to hitch up front and push it in. A front hitch gives you pinpoint control and allows you to maneuver in really tight spaces. Product was exactly what I needed, is made well, was priced right, and delivered promptly. Couldn't ask for more.
Did not fit the vehicle it was meant to fit, had to modify hitch and drill holes on frame. Have had good success with etrailer in the past, this was not.
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I have had the front receiver hitch installed on my 1996 Suburban for about a year now. I have a 12000 lb winch installed using that receiver hitch. I have gotten stuck twice and had to use the winch to extract the truck. Very glad that I have the front receiver hitch as it made putting on the winch very easy. Also useful for mounting a receiver mount bicycle rack to the front as well.
Product was shipped promptly and arrived a few days later. Packing was good for a heavy item with pointy edges, no issues breaking out of the box. Installation on a lift took about 30 minutes on my 1999 K2500 Suburban. The bolts were long enough to allow for my tow hooks that were already in place. A bolt stringer to pull the rear bolts from the top (inside the frame) is provided along with nuts, the other four just replaced the stock bolts that I had that mount from the bottom into tapped frame metal through the tow hooks. Curt makes great quality stuff. Clearance was reduced a little but I'm not concerned about it.
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
Terrible, they sent the wrong hitch and now want me to pay shipping for the return
# 9
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Front Trailer Hitch for a 2014 Toyota 4Runner was delivered quickly and in perfect shape. Installation was straight forward, however I spent more time trying to remove the super tight 4 bolts from the frame in order to install the hitch. There's not a lot of room once the hitch is installed to tighten the the upper bolts. I had to use a smaller ratchet in the tight space. I also used anti-seize on all the bolts prior to re-installing them. This hitch will be used for a fishing cooler rack and rod holder while on the beach. So Far I'm very satisfied with this product. Draw-Tight makes a good product.
Super easy install. 25 min. Use a Jack and angle it in like the first picture. Then when you get the 2 side bolts almost snug, use the Jack to move it up into place. Then just put the 4 stock bolts back in and torque to specs. I will use this front hitch for a bike rack, winch and fishing cooler in the summer Thanks Etrailer, it went in as easy as you said it would. super fast shipping also!
# 10
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I Installed this unit on a 2011 Toyota SR5. The two areas that took the most time were getting the M12 bolts threaded into weldnuts that had been exposed to the elements for 8 years. I live in the northeast where salt is used a lot in the winter. The other time consuming area was trimming the plastic panels after the hitch is installed. I had to trim in a slightly different area than shown on the diagram. The trimming took a lot of trial and error. Hopefully, a picture of a trimmed panel is shown here. I am a 67 year old amateur mechanic installing this on ramps in my garage. It took about 3 hours including a trip to the auto parts store to get a set of shallow 6 point metric sockets. The deep dish 6 point sockets that I owned would not work for removing the frame bolts. The frame bolts came out much easier than I thought they would using a breaker bar. My impact wrench wouldn’t fit up there. Not enough clearance. Overall, I am very satisfied with the quality of the hitch! I plan on using this hitch along with a load extender to transport long heavy items such as rough sawn lumber, etc. I might also need it if I get stuck getting into or out of hunting camp.
I am just disapointed with the hitch mounting holes not lining up! I know what I am doing and did not tighten up bolts whatsoever so there was room for play and still did not work. I tried so hard to make it work that now one side of the mounting broke on my 4 runner. I really like etrailer products but this one came in wrong but I had to make it work for my needs. I could not wait another week or 2:( Also, my 2020 4RUNNER is stock height with 17 inch BFG tires...Should I have this clearance? Is it standard and looks correct? If I would have had time I certainly would have asked for another hitch that was made correctly. Again, I like etrailer and usually have great luck but this time it cost me money and time and heartache and just overall terrible experience. I would so much appreciate if you made this experience right for me.
# 11
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
product fit fine, install was about 30 minutes...maybe a bit less. Only needed two sockets, extension, ratchet and torque wrench. Shipping was quick. Only issue I had: product was not listed as fitting a two door Jimmy/Blazer. Contacted e-trailer and they said it would not work. Called Curts and they confirmed that it WOULD work. Also, since I have both a 2 and 4 door, I could not find any differences in the vehicles. Other than that, it was a fine transaction.
This is the 5th trailer hitch that I have ordered from etrailer.com. They have all worked great. On Monday I called and spoke with Amanda about a front hitch for my S10. I received it Tuesday afternoon. I had it installed within about 30 minutes, though I could have done it in about 10 using an impact driver. It went on perfectly and works great. It is a strange thing to "back" my trailer up with it in front of me. I am not sure how it would work with a very large or enclosed trailer (mine is not.) It works great and looks beautiful on the front of my truck. Thanks again etrailer for a great hitch.
# 12
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This is the third Curt front receiver hitch I have used on vehicles. The hitch was good quality with clear instructions included. It definitely helped during installation that I had a friend and shop to do the install as the ends had to be spread a hair to slide around the frame rails. We had the hitch installed in about 20 minutes. The reason for the average rating is that this is supposed to fit the 2010 Ford F150 Raptor. Although it does fit, you cannot reinstall the skid plate without sever modifications and then, the skid plate would just be for looks. The end of the hitch also sits behind the bumper requiring me to purchase a hitch extension in order for me to install my receiver mounted winch. I bought the RM-071-1075 from etrailer in order to mount the winch. Recently I had to use the winch and had no issues with this set up doing a straight pull. When we tried to pull at a slight angle, I was afraid of exceeding the capacity of the hitch due to the extra leverage caused by the extension (big heavy Raptor on 37's buried in mud and snow). Overall I would have given the receiver hitch 5 stars if the description mentioned that there would be issues installing on a Raptor. I probably would have done a traditional bumper mounted winch but I like being able to move the winch front to back (which is how I ended getting out of the situation).
This is my second Curt Front mount Hitch Receiver I have purchased. I use it to launch my boat and wave runner. The mounting instructions need to be corrected. I placed this receiver on the front of a 2011 Ford F150 4wd. I found it easiest to place the Bolt on Forward passenger side first. The instructions said to place bolts and bushings from inside. There is not enough clearance between the radiator and the frame to place the bolt from inside out. I found it easiest to mount with the nuts closest to the radiator. I did not trim the bumper fascia and it still fits perfect. (plastic has some give) The 5/8 fish wires are great! All hardware is packaged and taped to Hitch.
# 13
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Product is great! Exceeds my expectations for ease of installation and performance. I removed the 3” spoiler completely vs cutting for hitch. The key is to “dry fit” in place and use a metal punch to mark all your drill holes. Wire bolt feeder worked great for installing bolts. I used the hitch to mount my eight pole rod & cooler holder for surf fishing.
Super fast shipping,but could use better packing.Hitch actually made a large hole in box,UPS driver had me check to see if anything was missing.Easy install,but try finding a 17/32" bit. After seeing how big the front opening is I just used a 1/2" bit. I think it took longer to remove, trim and reinstall the front spoiler than the rest of the job. Looks great installed
# 14
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
the install went very good but i do have one suggestion and see if your maker can put a notch in the middle hole to look like the tow hook it would make the install way more user friendly also had a little problem with one of your bolts after i had fished it down the hole the treads were burred and the nut wouldn't go on all the way so i had to fish it back out what a pain that was but got it done and replaced with one of the other bolts that you supplied me with and it went on great. now i have a ? about the hitch height mine only sits up at about 11 inches and change will that work with your snowplows that say they need 13 inches or will i have to do something different? but thanks for the great turn around time in getting it here quick.
Well made and easy to install. All of the necessary parts were included and the video on the product page made it a breeze to install. Working on my driveway with no lift. I am 73 and used a floor jack to lift it and hold it in place until the first two bolts were in place.
# 15
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2022 TRD Pro fits snugly. To keep the OEM skid plate, you can remove the skid plate’s 2x front spacers and spacer washer locks. Removing this will allow you to fasten the front 2x M10 oem bolts. The 2x rear M10 bolts will need to be replaced with 2x smaller length M10 bolts that are at half the size of the oem bolts. My local hardware store had plenty of options.
This front hitch is a perfect fit for my 4Runner. It was easy to install.
# 16
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The Curt front receiver fit perfectly on my 2002 Jeep Grand Cherokee. However, the welds on the horizontal hitch bar all had to be trimmed back with a grinder for the washer nuts to fit properly! A little bit of spray paint and you can’t tell the difference!
2000 Jeep Grand Cherokee Limited 4.7 v8 fit perfectly went together easily with new snow plow.
# 17
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Worked out great.. A little trimming on the facial of the bumper.. The fish line awesome little tool... Thanks
as always, this would be like the 10th time I got hitches from Etrailer.com, outstanding products with all parts needed and clear i structions online as well on paper
# 18
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Very well made and really fast delivery, excellent transaction and the people at trailer put a lot of effort into seeing you get your order
My son and I finished putting on both hitches front and rear, Rear was very easy after we cleaned out the rust. The front was a little bit of a chore because we did it with car ramps and it took some maneuvering to get the bolts tightened down. But we got it done and it looks great on my Liberty. Pictures above. I would definitely recommend you guys, the instructions were very helpful. Will do a review tomorrow gotta watch the games now.
# 19
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Straight forward installation. Great for moving my trailer into a tight location and also provides a great tow point with a shackle attached.
This is my Third front mount receiver hitch. Never had a problem and they fit perfect for the vehicle I order them for.
# 20
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!
Fit perfectly with tow hooks on my 2016 Tundra. Had my mechanic install it and cut the hole in the skid plate. The receiver is shown with the Kuat Hi/Lo hitch extender and a bike rack.
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"