# 1
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 2
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Very versatile - can use it on both my vehicles that have very different hitch height. Clean welds, super solid. Weighs a LOT!
# 3
Flash Secure Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
Very strong, easy to install and very secure. Yes a bit pricey, but well worth the money. I did notice there was what I thought was an unusual amount of play in the receiver. I called etrailer and Marcia was so very helpful and very concerned that I may have received the wrong product. She even called the manufacturer and found out what the changes that were made by the manufacturer which made the pictures incorrect. My hat is off to Marcia and all the folks at etrailer
ball mount fits loosely in the receiver so that the pins that extend out from the ball mount shaft through the holes in the receiver don't extend out far enough, for my liking. This is because since the ball mount shaft has so much play, it will shift to one side. Then, the pin on the other side does not extend all the way out of the hole so that it is not flush. True, i am being paranoid. However, i imagine a case like a crash where enough force could pull the shaft out from the not fully extended pin side to release the trailer to wreak more damage. I would just feel more secure if the pins went out further through the receiver or the shaft was not so loose. Otherwise, i really like the product a lot... enough to give it four stars... :o)
# 4
B&W Tow & Stow 3-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black
Gone are the days I need to carry three different hitches with different sized balls on them. Gone are the days when I, or others, walked around the back of my truck and cracked their shin on a protruding trailer hitch. I keep this folded up in front of the drop where it's not going to catch anyone by surprise. When I'm ready to use it, I simply pull two pins out which allows it to drop free and rotate out. I choose the height I need and install the two pins/clips. To rotate the balls, again simply pull the third pin and rotate to desired size. It was more than I wanted to spend at the time but since I'm glad I spent the money.
Super convenient and well worth the money. All 3 of my trailers have a different ball size, and this is a breeze compared to constantly swapping tow hitches. Keep the pins well lubricated, and they slide well maintain their appearance.
# 5
Flash Secure 2-Ball Mount w/ Chrome Balls - 2" Hitch - 4" Drop, 5" Rise
Love the design with no locking through pins to worry about. Only reason for three stars is I received the product with cosmetic damage from being dropped.
Works great. The locking pin feels like it could be a bit wider but otherwise I love it. I’m a novice at towing so the adjustability of the height has helped make sure the towing has been optimized at all times.
# 6
Flash Simple 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
Works great. With all the adjustments we can get our trailers to haul level now. Quality looks really good and it has the 2 size trailer hitch balls which makes it way more convenient.
VERY HAPPY, BUT STARTED TO SEE SOME RUST ON THE HITCH BALL AND ONLY USED TWO TIMES. THE VERSABILITY OF THE PRODUCT IS GREAT. OTHER THAN THE SMALL AMOUNT OF RUST ON THE BALL ITSELF, IM VERY SATISFY AND WILL BUY FOR MY OTHER TRUCKS.
# 7
Rapid Hitch Adjustable Aluminum Ball Mount Kit - 2 Zinc Balls - 5-1/2" Drop, 6-1/2" Rise
Sooooo....you sent me a product that was somehow put together backwards and I cannot take them apart somehow the ballhitch is stuck on the male portion backwards and defies gravity and doesn’t need a pin to stay on(becaue thier is no where to put the pin in cause it’s backwards
Have done about 5k with this hitch, just once with a 4500lb camper but mostly with a 3000lb cargo trailer. The former in a highly raised position and the latter in the absolute bottom position. The hitch has worn very well and shows no signs of excess wear, save for the surface of the 2" ball, but it's not concerning. On a Jeep Grand Cherokee with a stock suspension, this seems to give the right balance of range of adjustment without dropping so low in the lower configuration as to scrape through dips, though it can still be done on very sharp dips with the hitch on the lowest setting. Overall, very pleased with it and love that it's lighter than steel and won't rust.
# 8
EZ Heavy Duty Adjustable Hitch with Combo Ball - 8" Drop/Rise - 14,000 lbs
Just did ~500miles with about 5k worth of car plus trailer over hill and dale. Works great. No detectable wobbling, but pins are easy to get through holes (not too tight or misaligned). Heavy, but not like, completely unwieldy.
This Hitch does the job perfectly for all my trailers keeping in the upright position and did not notice any excessive rattle..
# 9
Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
Everything arrived on time and well packaged. I installed a Curt hitch receiver to go with this ball mount. Installation for the hitch went exactly as described and was fairly simple for even a novice like me. Very pleased with etrailer.com and with Curt brand products in general. Couldn't be happier with the process from beginning to end. And the hitch looks and works great!
etrailer is great! My hitch shipped quickly and was packaged well. Plus customer service has been great keeping me updated and staying in touch with my order.
# 10
Buyers Products Tri-Ball Hitch Solid Shank with Pintle Hook And Chrome Balls
Rusts easily. Chrome is non existent.
Great service!
# 11
Curt Pintle Hook with 2" Ball - for 2" Hitches - 10,000 lbs/16,000 lbs
This is an excellent hook. And it looks killer. etrailers exceptional service and quality is beyond compare.
Looks great
# 12
B&W Triple Tow Tri-Ball Mount for 2" Hitches - Black Powder Coated
Solid! Well built.
B&W makes a Heavy Duty Tri-Ball Mount...very solid
# 13
Curt Class II Euro Style Drawbar with 2" Ball - 2-3/4" Rise - 3,500 lbs
It is heavy duty and well-built. I am not disappointed at all and I get comments everyone smile from people who are used to traveling overseas asking where I got the European style hitch from. The only downside is the lack of interchangeability in the size of the ball itself but I don’t think that’s a big deal because I set it up for what I need it for and keep a vehicle vehicle for longer periods of time.
Solid, heavy as heck. Bought this model because 1) I only have 1 lightweight trailer (Malone xtralight, also purchased from etrailer at the same time) and it’s light weight. 2) I am stuffing this into an adaptor also bought from etrailer to further stuff into a receiver also purchased from etrailer. 3) All this is on the back of my 2018 Subaru Outback. Beings that it’s a Subaru it’s not going to be used to drag a huge or heavy trailer. I’ll repeat this part in my review of the adapter, buy probably from etrailer, a receiver lock that is sleeved, to be both 1/22 and 5/8 and long. That way if you don’t want this sticking way out the back (shin killer) you can use 1 lock and go all the way through receiver/ adapter/ and this ball mount. Otherwise buy you’ll need 2 locks 1 for receiver to adapter 5/8 and a second 1/22 to go through adapter into this unit. A side benefit is it’s just different. It’s not an everyday boring looking ball mount, it’s heavy duty so why not.
What our customers are saying:
"Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair."