# 1
Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black
Great product and Trailer has great customer service. It's to bad that the shipping companies do not take better care with the items during shipping! will receive replacement parts to fix what was broken, but it causes lots of extra work for the customer. will have to take complete jack off to replace the broken motor cover because of shipping carelessness!! regards, Dan Ewert
This little rig has teeth! Much faster than i expected. About a 30 minute installation from old lift removal to new and wiring. Super simple. Great addition to my hangar 18!
# 2
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 24" Lift - 3,500 lbs - White
Jack works very well. Not fast but gets the job done. Unfortunately I can't lower my tailgate fully without hitting the jack. Tried to rotate the head as I saw some jacks allowed. This one won't allow that. Very satisfied otherwise. Used less than one full season so can't offer an opinion on durability.
Mounted quick and easy. Plenty of wire for electrical hook up. Lots of power even with a full load of water in the front tank. The only change I made to installation was longer bolts to accept washers and nuts to the bottom side of hitch. I didn't trust the taped holes in the thin hitch frame. This was no fault of the new jack. Still working strong. A back saver that's worth the money. I should have bought one years ago!
# 3
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
Perfect replacement, works great, excellent shipping time and service. Just wish I had got the electric motor that goes with the legs.
Ordered this from etrailer instead of other sites as I knew the shipping would be faster. Sure enough I got the item in 4 days on Thursday and Installed it on Sunday. Very quick and easy. Took longer to get all my tools and set up items together than the actual work. The item was a exact fit with installation being feeding the legs through the holes in the floor down from the inside and installing the 4 clamping bolts to hold them in, the gear box on the lead leg and the cross bar and motor. Now it purrs like a kitten when activated instead of clanking and creaking and blowing fuses. Actual install time was probably 1.5 hours taking my time and injecting extra grease into the gears and lead screw. These replacement units have a grease fitting for both which is great and should allow them to last forever! Being a safety freak I used a 3 ton jack with a 4X6 placed long ways to catch the I beams under the trailer then placed 3 ton car jacks under the frame also and for extra safety backed my truck bed under the tongue for extra security while I worked. The price was crazy great, the fit was excellent and the shipping was fast as usual. less money in parts and 2 hours of work probably easily saved me a grand over taking it to a RV repair shop! Thanks etrailer. Saved me again!
# 4
Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs
It installed very easy. For a 2500lbs jack, it seems a little light weight. It does lift the trailer but seems kinda wobbly because the post size is so small. Other than that it works as advertised. Thank you for getting it to me so fast.
I just installed my new JET-2500 trailer tongue jack in less than 15 minutes. The light and extend/retract work great. I was not sure if an adjustable drop foot is available for more length but do not think it is needed. This is second purchase, first being Equalizer hitch system which is also even better with electric jack. Etrailer exceeds customer expectations by follow up email and definite concern to keep their customers satisfied. Great Company! Thank-You Ron Williams
# 5
Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
Beautifully made and a solid drop leg. Do I need to say more? You get what you pay for.
Product was exactly what I was looking for. Only issue is the one square latch pin is missing.
# 6
Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs
I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."
Awesome product. My back thanks you. Very easy to install. Only thing I would change is the speed of the motor. A bit slow but still better than hand cranking.
# 7
Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System - 10,000 lbs
We love our one touch jack system. We used in on a 3 month camping trip out west setting up probably 40 plus times and we continue to use our camper and the jacks work great!
This has definitely been one of the greatest additions to our Stryker travel trailer. Order was received a day earlier than expected and all in good condition. Installation for myself and two other guys was a slight bit time consuming (due to my wanting all the wires hidden in the underbelly of the trailer). Watching the system level my trailer, with a touch of a single button, impresses me still today a year later. Great purchase and I would definitely recommend this product.
# 8
Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift
Pros: Works better than I anticipated. Looks great and has better ground clearance than the stock scissor-jack stabilizers. Cons: Installation instructions/documentation weak or non-existent. If all of the instructions, wiring diagrams and documentation were in one place on the web page under a separate tab rather than having to dig through the reviews and the Q & A’s, I would have given this a 5 star rating. I ordered the LCI Power Stabilizer Jacks with the white switch Kit (LC369774) because I wanted the switches mounted in the camper wall so they would be better protected than if they were mounted in the flimsy fender skirts of my camper. I also needed the bolt-on spacer kit (LC673594) for both the front and rear jacks to clear a propane line that runs along the length of the frame. Installation was relatively easy, although there are NO instructions on how to install the spacers kits; the video on etrailer.com was no help whatsoever with the installation. I bolted the jack mount brackets to the shorter side of the spacers using carriage bolts and flange nuts; the slotted holes in the spacers accepted the carriage bolts, aligned perfectly with the holes in the jack mounts, and allowed me to install them without having to try to fit a wrench inside. Then it was just a matter of drilling holes in the frame at the appropriate spacing for flange bolts/nuts through the slotted holes on the end of spacers. I was very pleased with how the switches and the switch compartments looked once installed. Again, though, it took lots of digging to find the wiring diagram and then the matrix for the switch wire colors, because the wires on the white switch are colored differently than the black switch that all of the diagrams show. Also, it states on the jack installation instruction sheet that the power must be a minimum of 10 gauge wire (AWG-10), but nowhere on the wiring diagram does it say anything about that. AWG-10 is a MUST because of the way current drops over a distance. In the case of my camper, it is a 30 foot run which requires that gauge of wire for 20 AMPs.
This stabilizer works very well. I replaced the original Lippert unit on my 2008 5th wheel as the parts I needed were no longer available. The original Lippert unit worked great until some idiot in a drunken stupor decided to move it with the stabilizer in the “down” position. I probably won’t do that again anytime soon. DOH!!!
# 9
Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black
As always a big help in getting what I need, and wanted. Good tec help, fast service. Already installed.
The bolt pattern matched my trailer so it was very easy. No skill needed. I soldered a connection on and hooked it directly into the battery. I had to drill a hole for my foot extension. So far so good. 23 foot travel trailer.
# 10
Electric Trailer Jack - Drop Leg - A-Frame - 22-1/2" Lift - 3,500 lbs
This jack was the perfect solution for my application. I have a new enclosed trailer that came with a manual crank and only a tiny battery to run the lights. I did not want the expense of having to buy and cable up a larger battery to just support the tongue jack. Took me 5 minutes to install this new jack using the three bolts that were already on my OEM jack. Now I just back up my truck, plug in the 7-way, and I'm able to move the tongue up and down as needed. Great!
I love my new electric trailer jack ! It has a 7 pin RV plug which makes it so convenient to power. There are lights on both sides to shine onto the hitch after dark. There is a bubble level on top to know when the camper is at least level enough to start setting up. It all works great !
# 11
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.
I finished the assembly and install of the power twin II stabilizer and have included pictures of the install. This is a good quality unit and I am very happy with how it works. Bob
# 12
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black
I was extremely impressed with the recent technical and customer support from etrailer. Over the weekend, they answered my questions to select the appropriate replacement electric jack for my Airstream. Also, when there was a shipping delay (not etrailer’s fault), Rose provided prompt responses and professional support. I will continue to use etrailer for my RV needs.
Works flawlessly. Maybe the only thing I could complain about is it is slower than I think it could be. Along with the side lights could always be brighter. Works great, install kit is awesome, and it works without a stutter.
# 13
Phoenix Electric Trailer Jack with Remote - A-Frame - 26" Lift - 5,500 lbs
This is awesome and so easy to install. Took longer to open the box then to set it up. We had ordered something similar to this for our old camper. It took us hours to get it to fit right. This was extremely easy to install. My husband loves the memory feature on this thing.
My order arrived damaged. etrailer was immediate to remedy. The same day a return for pickup at my home and a new item was shipped out. I plan on installing the jack tomorrow.
# 14
Electric Jack w/ Footplate and 7-Way Plug - A-Frame - 25-1/8" Lift - 3.5K - Black
The 7-way plug electric jack is a great replacement for my crank handle jack. I did not want to install and maintain a 12V battery for just a jack so this is an easy plug and play solution for me.
7 pin easy hook up for trailer jack does not work on my 2020 ford ranger. Missing 12v power to jack control? any advice in Trouble shooting. Is there a compatibilty problem with ranger to your jack 7 pin config? Will use manual hook to battery rather then ask for replacement jack if possible?. Before I cut any wires and void warranty. Is all I have to do is cut and splice the fused red wire to a positive battery terminal to do this. What abount grounding? Please advise should I modify and wire direct or return jack back for refund/replace
# 15
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
Product was an exact fit for my application only problem I had was key inside gear box fell out but easily fixed once I figured it out.etrailer was spot on helping me find correct jack for my ca.per works great
I thought replacing the landing gear would be much harder on my 5th wheel but they when in without a problem and are still working great. The video walks you through the installation step by step. Rick
# 16
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!
Bulldog BD500199 installed on 2006 Jayco Jayflight 27BH. Bought this powered jack to replace the non-functioning electric jack that came with the camper we bought 6mo ago. We’ve been using the manual override on the old one, so having a working jack is going to be great:) Just installed this new unit yesterday, so have only used at home so far, but it seems to work very well. Speed is good. It has the drop leg with spring pin for quick adjustment which is cool. It has a built in light which is fairly bright and should come in handy for setting up at night. Installation was very easy. Literally had the old jack removed and new one in place in about 20mins and that included getting the jack stands set up. The hole in the A-frame was big enough for the larger diameter tube of the Bulldog unit, so no fitment problems. I’ve got photos showing the old unit and new. Forgot to take one with the jack removed. There was additional time wiring, but it was only another 20mins or so. Most of that time was spent deciding on routing and zip tying the wire. There is only one wire that hooks up to the battery positive post and there is an internal breaker in the unit so you don’t wire in an external fuse. Heads up there are no wire terminals in the kit, so you will need to have your own to crimp onto the wire. You’ll need a 10ga connector, likely a 5/16 or 3/8 ring terminal but could vary depending on your battery. The wire lead could have been another 12” longer, but it was just barely long enough to reach the positive post after I flipped the battery around to put the positive post on that side of the frame. Also should note that this unit has a dual mounting pattern that allows for turning the head unit 90deg to face sideways, which is what I ended up doing. Facing forward, the head of the jack was really tight up against the propane bottles/cover, so turning it sideways fit much better with our camper. Looks to be well built, so hoping it lasts a long time, and I’m looking forward to not using a manual override crank next time we go camping!
What our customers are saying:
"Very broad selection and outstanding service."