# 1
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 2
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 4
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Haven’t used it yet, but looks good. I’m not sure what height offset I need, so this kit gives me several options, plus two ball sizes. Really good value.
Ball mount kit arrived quickly (within a few days) upon placing order online. Parts were shipped loose in box and bottom flap on box was open when received. Fortunately, all the parts were still in box and in good condition. Kit includes ball mount hardware I need to pull trailers with different hitch heights.
# 5
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Package was delivered empty ... see photos
# 6
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
This drawbar was clearly used. See the picture. I asked etrailer about it and sent this picture but the person that replied, Noah, thought it must have been bumped around in shipping. If shipping caused this much damage, it's a poor quality product. If it was, in fact, used, then etrailer lied to me. Either way...not good.
# 7
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 8
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 9
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 10
Curt Multi-Ball Mount w/ Tow Hook for 2" Hitches
Cool to follow up on your product. The multi-ball works as it should. I bought it since I didn't know if the trailer I would get would be 2" or 2 1/4. I tow a 4,000 # trailer/race car with it. It's a heavy piece to carry around, but I feel that it will last a good many years. I did make a spacer to cram into the receiver, so the hitch doesn't rattle as much. Otherwise it's great. Tim E.
the packaging showed up as a mess, need to see if its damaged when I open it
# 11
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works perfectly. Fast shipping. Very Satisfied.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 12
Draw-Tite Drawbar for 1-1/4" Hitches - 4-3/4" Drop - 7-1/2" Long - 3,500 lbs
Exactly what I needed. I bought this Mercury Mariner used and it had factory installed hitch with a 1 1/4 receiver. I needed a drawbar with a substantial drop to tow my utility trailer somewhat level. Local shops had lots of 2 inch drawbars with drops but no 1 1/4 and I was even told that they weren't made and I would have to use a 1 1/4-2 inch receiver adapter do get what I wanted. You folks had what I needed and it arrived quickly. I should have looked here first.
I have a 2012 Outback. The car has more ground clearance than my previous Outback so the 2 1/2" drop on my old drawbar resulted in the rails on my motorcycle trailer tilting backwards slightly. This made loading the motorcycle a bit tricky because it wanted to roll backwards when loaded, until strapped down. I looked all over town for a drawbar with more drop but was unable to find one. Finally found this drawbar and it worked perfectly with enough drop to level the rails on the trailer. I also like the fact that it is a bit shorter than other drawbars and doesn't stick out as far.
# 13
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 14
Convert-A-Ball Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 14,000 lbs
Product is awesome. Shipping container was destroyed when it arrived. Product was not hurt.
Was hoping this would help with shock reduction. It doesn't. Has to fit loosely into hitch to function so it slams side to side and front to back. Would not recommend. Very disappointed in this purchase. Trailers service is exceptional. Easy to order. Arrived quickly, well packed.
# 15
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
# 16
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 17
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
# 18
etrailer Ball Mount Kit for 2-1/2" Hitches - 1-1/2" Rise or 3" Drop - 18,000 lbs
I am a frequent etrailer customer, the variety and availability of quality components and excellent service is what keeps me coming back. When trailering I strive to be as safe as possible, which is why I chose this heavy duty ball mount to tow my 10,000# car hauler trailer. With this very robust piece, I can be assured that the connection between my truck and trailer is secure.
This was our company's first ETRAILER order. My original order was for a Blu Ox receiver reducer. The plan was to continue using our current 2" drawbars with the 2 1/2" receiver on the "new" (2008) truck. Upon installation it was very apparent that there was way to much side play for safe towing of heavy loads on gravel roads. ETRAILER customer service was contacted for assistance. Holly was extremely knowledgeable regarding the product line and also had "hands on" experience with trailer towing. She not only guided me to the best resolution to my issue; but, also expedited shipment of the replacement drawbar. She further emailed a return shipping label for the reducer that was easy to print, along with straight forward and easy to understand instructions for the return. The UPS driver even commented about the label being the correct size as opposed to many undersized labels that he has received. Our company will now use ETRAILER as our "go to" vendor for trailer repair and towing supplies. As for the drawbar, the construction is one piece forged steel with an I-beam design. The ball appears to be high quality. I have complete confidence that the drawbar and ball kit will perform as needed when we are towing equipment or logs on gravel and dirt roads; as well as, off-road.
# 19
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 20
Curt Vertical 2" to Fixed Ball Mount - 12-3/8" Long, 2-1/4" Rise
Purchased for a Dodge Journey with vertical mount hitch. Waited 5 months to get one from Chrysler and finally gave up found this one online. Sturdy design and does what I need it to. My only complaint is there is no recessed slot for the hitch ball to screw in tightly.
Tried to get this from the Dodge who put on the hitch. After six weeks of waiting I called you and got it in two days. Thanks.
What our customers are saying:
"Very broad selection and outstanding service."