# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
What can I say that you haven't already heard? etrailer.com made this such a painless and straight forward process for selecting the front hitch for my 2015 Jeep Rubicon Unlimited that I can't believe I didn't do it sooner. The Curt front hitch for my jeep arrived quickly and in great shape, very well packed. On unpacking I found my hardware and instruction firmly secured to it so it didn't get mixed up with my rear hitch, good forward thinking. The hitch is robustly built and you can see the care that goes into the quality, all the welds are neat and tidy and the finish is excellent. The hardware is all coated for long lasting performance and the fish wire is beyond handy. For the installation of the front hitch the instructions are a little lacking. This is not to say bad or confusing, just lacking a little more how to. The etrailer video on installing it made the process go smooth and easy. On my Rubicon model you do have to fight with the sway bar motor on the passenger side and the vacuum unit on the driver side, it is a pain but if you take the top frame trim off it is much easier to work. The bolt hole on the drivers side, pass a drill through it to make sure the ft is right because its very tight to work in that area and close won't work. Other than that, it installs exactly like the video. The only thing that would complete the package would be a template for clipping the front plastic shield, the Curt instructions include a sketch that gives you an idea but a simple temporary adhesive template would make it super simple to drill the corners out and then connect the dots with a tool of choice. But hey, that's just me. The hitch tucks up real nice and doesn't kill approach angle or ground clearance which is great for my application as its for carrying a winch when I need it. I would recommend etrailer.com without hesitation and strongly urge the Curt line of products based on what I've seen so far.
It was a great price to solve my problem of how to take my bike camping when I’m pulling my teardrop trailer. Installation wasn’t that difficult with the exception of the top bolt on the drivers side. The brake booster pump was in the way. Keep trying and you’ll get it in eventually. It took me about an hour to install.
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This front hitch is great! I purchased it to easily mount and remove a fishing rod holder and cooler rack, rather than mounting it to the bumper. It fits my 1997 Jeep Wrangler perfectly. Install was very easy, but you do need to have the right tools for the job. The instructions were very clear and there is a [online video] from Curt Manufacturing that was easy to follow as well. Hitch is very high quality and sturdy. Completely enjoyed working with etrailer as well. Great prices and I couldn’t believe how fast they got my order shipped after my order was placed. Looking forward to many years enjoyment from this hitch and will definitely shop etrailer again!
Fit is exact, excellent product. A over sized drill bit or step bit recommended for making access holes larger.
# 4
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Have used it a few times last fall to carry a cooler and fishing rod cart on the beach. So far have not had to use as a recovery to get pulled out of sand or pull another vehicle with the tow strap loop attachment that I bought as an additional accessory. The top mount on the bumper was ideal since gives more clearance than below bumper mount when in the sand. Keeps the cart up high. The paint on the hitch is very nice.
The item was packaged poorly causing me to have to touch up prior to installation. Large box with no stuffing causing the item to rattle around. Probably got scratched on staples in the center of the box that served no purpose. The installation instruction were unclear and contained errors. There we multiple washers and you had to guess as to where to use them. Instructions showed bolts installed where there on holes
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This is a high quality hitch that fits the Gladiator perfectly. The hardest part of the installation was removing and reinstalling the push fasteners on the plastic air dam. While the hitch fit is perfect, the instructions for cutting the plastic air dam leave something to be desired. I finally had to eyeball the location for the hole and then found that the suggested utility knife simply wouldn't cut the plastic air dam. An oscillating saw solved the cutting problem easily and the best guess location worked out. Am I happy with the end result? You bet! Would I do it again? Absolutely.
Just received the front mount hitch receiver from eTrailer, haven’t installed but can tell it’s a quality item. Extremely impressed with eTrailer’s packaging technique to stabilize the receiver in the box for shipping. They have devised a system to hold the hitch assembly completely stable inside their heavy duty box to keep the heavy hitch from busting through during shipment. The complete assembly arrived without a scratch even though the shipper did manage to make some holes in the box. Excellent work eTrailer and first scratch on my receiver happens tomorrow while I am installing. My scratches are OK and hold my memories, but I don’t like other’s inflicting harm.
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Front hitch was received in a timely manner. The Hitch itself does not line up with the bumper of my 2002 Jeep Wrangler X. It is close but no cigar. Will have to make some type of adjustment to align the bolts. This I thought was a bolt on installation. Disappointed but will keep the hitch. Hitch is to be used to move trailers and to mount winch that can be used on the front or rear of wrangler.
Perfect for what I need. Can adapt it for many different uses from winching, cargo carrying, bicycle carrier, or any other use my tinkering mind comes up with.
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Fits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.
Installed real easy. Cuttingbthe plastic rock guard was the hardest part.
# 8
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Fit was tight but with a floor jack I was able to install. Looks like it will work well for me. The bolt guide wires were critical to installation. Very good construction of the hitch.
After correcting a mistake and taking another receiver back at their expense, etrailer shipped me the correct hitch for my 2017 Jeep Wrangler Rubicon Recon. If your Wrangler has the steel Hard Rock / Anniversary Edition bumper in the attached pictures, this is the right receiver. It's very well made and has a much better paint job than the Draw Tite that didn't fit my Jeep. The tolerances are VERY tight, so much so that I had to hammer it into place with a block of wood. The supplied fishwires made getting the carriage bolts and spacers in place a breeze. Unfortunately, you will have to remove the steel skid plate that's attached to the bumper. I thought it might be possible to cut it around the hitch and put it back, but it doesn't look there's enough clearance. Great service from etrailer!
# 9
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.
I chose this product because it was among the more inexpensive front hitches I could find. I plan to build a t-bar for it and use it in conjunction with a homemade headache rack to carry 16 foot garage doors. Like other reviews and vids I have found, the bolt up is hard. I reversed the bolts and use the new ones on the outside, as well as removing my grill. My truck is a 2003 - so not much room like the 2008 and newer trucks.
# 11
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.
I plan on installing it tomorrow, however first impressions are not good. The box it item was shipped in was extremely damaged. Torn, ripped and taped up on all sides. The delivery person said that due to the sharp edges and the face it wasn't secured in the box (lose) led to the damage. It appears the item was not packaged properly. I just hope all the parts are there. More to follow.
# 12
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Ordered the same hitch from Amazon, and showed up not J-Pin ready, with (1) hole drilled for a hitch pin against the weld. Can't run the nut flush because of the interference with the weld bead, and no 7/16" hole present. Returned it. Ordered another one from etrailer direct. Called in the order to make sure they QC'd prior to shipping. Assured me they would. Box never opened, and the same nonsense showed up. Not happy, trying to work it out.
Fit Perfectly, super easy to install, and super fast shipping! Holds Hollywood Bike Rack Great and very solid for my two E-bikes. Thank you etrailer!
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitched arrived three days early and I was able to install it in less than 2 hrs with a little help from my wife and a floor jack. Perfect fit!! No shimms necessary Vwrry happy.
The hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
Terrible, they sent the wrong hitch and now want me to pay shipping for the return
# 15
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
A good install! A bit of trimming for my application , but the bolt holes lined up perfectly. This front hitch was not specifically for a Lexus GX 460 but I decided to try it. There is a small area of lower bumper plastic that had to be trimmed. The hitch was pushing up against it before it was high enough to be in place. Upon trimming that area, it went in perfectly. If trimming the lower plastic is not for you, probably best to pass. However for my use, it works well. It is a stout piece, very strong. I added a pic with a red line to show where the trim needs to be.
Installed on my 2012 Lexus GX460. Perfect fit once I cut the center section of the lower plastic area for it to fit. Also had to trim the bottom splash guard and bend in the L brackets that hold it on. Took me about 2 hours. Very happy with the outcome. Now can mount snow blade for the driveway clearing…or any other hitch items.
# 16
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original. My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side. The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done. I already have a winch mounted on a hitch bracket, but may use this for more things besides that.
It wasn't fun to install by myself, but managed to do it in a few hours. Worked out great so far, I've hauled motorcycles on hitch carrier for about 2k miles so far and had no problems.
# 17
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
I ordered this literally less than 24 hours ago and it arrived to my doorstep!!! I think etrailer needs to call Amazon and tell them how it is done. Like honestly, I am not even prepared to put it on yet as I was expecting a week for delivery! Holy cow, do you all sell groceries as well?
# 18
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.
# 19
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitch was well-made, and installing it was very easy. However, the design of the hitch is somewhat perplexing. The hitch receiver hangs about 3 inches lower than it needs to, which reduces the ground clearance on the front of the truck significantly. See attached photos. The hitch will work until I find something better, That restores the front ground clearance
Well so far so good. It was a little difficult trying to do it by myself, got most of it done and then had to go to a autobody shop down the road to tighten up the 4 bolts.
# 20
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!
Fit perfectly with tow hooks on my 2016 Tundra. Had my mechanic install it and cut the hole in the skid plate. The receiver is shown with the Kuat Hi/Lo hitch extender and a bike rack.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."