Most Popular No Ball for Hyundai Santa Fe

Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

Click to Enlarge

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Click to Enlarge

I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.

Click to Enlarge

Click to Enlarge

I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Good and strong but not a great angle/height for my application so had to go to a straight line fit.

With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.

Click to Enlarge

I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.

Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.

As advertised and quick delivery, I am an Etrailer fan!

Strong and works perfectly!

I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.

Easy install, everything included, and great instructional video. Worked out great for my RAV4.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

Click to Enlarge

Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

Click to Enlarge

Product is exactly as described on the etrailer.com website and measurements and dimensions fit perfect. Easy phone order process and prompt delivery, standard shipping arrived 3 business days after the order was placed. The extra long version of the ball mount makes it perfect for me to put on the bike rack while towing my horses.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.

Great product for getting out past the tire carrier on a small SUV. Customer service was wonderful with great follow through and any assistance I needed I will definitely use etrailer agin

Click to Enlarge

Click to Enlarge

Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.

As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !

Click to Enlarge

We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.

Click to Enlarge

Rusted within 30 days. The manufacturer refused to warranty the product. I have continued to use it, but it has required some serious rust mitigation and is a flawed product.

Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.

This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.

works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.

Click to Enlarge

This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.

Click to Enlarge

Slightly longer, so you can open your tailgate with a cargo trailer attached. Trailers with a tongue jack that is forward are problematic for tailgates...

I’m pleased with the product and how prompt the delivery was. However the packaging was insufficient and the packaging was torn open all over. Scuffing of the finish is a result and of little consequence due to the intended use. It’s a stinger w/ball for motorhome. May I suggest better packaging in the future

Click to Enlarge

It's a drop hitch not much to say, exactly what i ordered, and fast shipping.

Basically I bought this ball-mount after I installed the low-slung hitch receiver from ETRAILER to know I have an ability to haul something if really needed in an emergency situation. The receiver hitch was purchased for my Thule bicycle rack , purchased from Etrailer.

Click to Enlarge

I had previously purchased the etrailer hitch for my 2021 Ford Transit 150. It was a little short in length and the bumper prevented my current ball mount from working. As always, etrailer had the perfect solution. The Draw-Tite is well made and will now remain permanently with the van to be handy whenever the need arises.

It works fine, it's a drawbar. Etrailer is always easy to deal with and decent pricing.

I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!

Click to Enlarge

Drawbar looks great and will be using in next two days. Thanks!

This stinger fits perfectly with my boat trailer and pickup. Having a bad back, the reduced weight is very helpful when removing and installing my Rock Tamer mud flaps. Shawnee was a huge help in determining what would work best for my application!!!

Very nice ball mount. Smooth, one piece design. Unlike my previous ball mount, it's long enough (enough straight length between the pin hole and the beginning of the bend) to accommodate a Blue Ox Hitch Receiver Immobilizer II, yielding a nice, tight connection. Attractive polished finish. Made in Taiwan (according to the box it came in). Photos show it attached to a Hidden Hitch Class III Hitch Receiver, secured with a Blue Ox Hitch Receiver Immobilizer II, and a Curt 40053 2-inch stainless steel ball.

Click to Enlarge

Click to Enlarge

Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".

Each time we go camping we look for ways to improve the experience, the C45230 will allow us run with a short or long ball mount, the longer extension allows me to open my tail gate without disconnecting from the trailer. I looked at other manufacturers but was only able to find what I was looking from CURT, and etrailer offered the best price.

Click to Enlarge

Click to Enlarge