# 1
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I used 2 inch square tubing cut the length of the tie down support bracket in my 2007 Honda Ridgeline and secured with a stainless bolt and wing nut, use a large enough washer to cover the diameter of the supply hole in the Honda Ridgeline bracket on the truck. A couple of notes: Be sure to use something as a cushioning gasket to insure a snug fit and to protect your truck lining. I used rubber or foam exercise mat cut to the same as the aluminum square tubing. Use a washer that a combination of hard plastic and metal to avoid the corrosive effects of dissimilar metals in contact with each other. last: My 26" full suspension bike fits, but I have swing it to one side slightly before i close the tailgate and lift the bike up and slide it down....It's a very snug fit but the suspension adds pressure to the tailgate and its works out very well. Or you could just use a tailgate extender.
Referring to special mounting instructions if you have a bed liner: (line #3). I do not have a bed liner, but I do have a molded plastic cap on my bed rails ('04 Ford F350). The first install over the plastic cap the locking pin or pin as called out in line #3 was nowhere near making contact with the metal lip of the metal bed under the plastic. What I did next on the second and final install was remove/cut away the plastic on the inside of the bed rail to allow the vertical portion of the "L" mounting bracket (Fig 4) to contact the metal bed. The locking pin is now at a position almost where it would protrude under the metal bed lip if I would remove the rest of the plastic under the horizontal portion of the "L" mounting bracket, I did not do that. After cutting a notch in the metal rail to accept the pin, the pin barely flushes out to secure the rack. A 1/4" longer pin would take care of this problem. One other thing that was not addressed in the install instructions was if you have a full size pick-up bed you are likely to attach the passenger side fork mount (Fig 2) to the right of the extension tube locking mechanism. The extension tube is a smaller diameter, so you will have resize the fork tube clamp (Fig 1) for the smaller tube. I can't explain how to do it other than it's a Chinese puzzle.
# 2
Rhino-Rack Hybrid Roof Bike Rack - Wheel Mount - Clamp On - Aluminum
Great bike carrier! Etrailer always provides me with high quality products with fast deliveries.
I love the racks, instructions were understandable, one of my end caps came in bad, it can wiggle off after locking but I emailed etrailer and they arranged a replacement quick with rhino rack, pretty nice of them, comes with rhino rack decal and just have to decide where to put it, out my bike up and took it for a test drive and it was very nice, I love their package because it comes with locks and way cheaper than the competitors, very satisfied
# 3
Rhino-Rack MountainTrail Rooftop Bike Carrier - Fork Mount
Love this bike rack! It fits perfectly with my Rhino Rack Cross Bars. I'm very impressed by the lack of wind noise. With the bike mounted on the rack, you can barely hear the wind noise at 60mph. With the sunroof open you can hear wind noise, but as long as the window is closed, you can only slightly hear anything if the radio is off and you are trying to hear it. Amazing! Can't wait to get more use out of it in the future!
I have used a lot of bike racks and this is the one I keep on my 4Runner. It just works. It is the easiest to take on and off, which is important for me because between me, my wife and kids I have 4 bikes that need to be rearranged often. We also use a roof box, kayak racks and a SUP rack so I am always taking things off and on. The front straps loop over the bar and tightens with an allen key, the back is a couple wing nuts. Since there are 2 straps up front the rack is very stable when a bike is on it. I like that it comes with locks and the skewer is super easy to adjust, clamp and unclamp. If it is cold, dark and damp at 6am and I am tired, late for a ride and still waking up this is the rack I go for because it is easy. There are a couple things to be aware of though... You will need to put a drop of oil in the skewer every 6 months or so to keep it opening and closing smoothly. Otherwise is can stick. Sometimes if the skewer is turned just right there will be a bit of whistle because of a hole in the clamping mechanism. If I turn it to a different angle the whistle stops. And after going through the car wash with the rack on my roof a dozen times or so the black paint began to have a bit of a rainbow sheen. Not sure if it is the bike rack or the soap my car wash uses.
What our customers are saying:
"Sent out an e-mail to you earlier this week asking which hitch woudld be the best choice for installing on a 2000 Venture van for hauling a bike rack with two bikes. You suggested the one that would be easiest to install..received in a matter of days..installation went great ..very well thought out instructions. Everything went smooothly and the hitch is up nice and snug..doesn't stick out..looks great."