# 1
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I used 2 inch square tubing cut the length of the tie down support bracket in my 2007 Honda Ridgeline and secured with a stainless bolt and wing nut, use a large enough washer to cover the diameter of the supply hole in the Honda Ridgeline bracket on the truck. A couple of notes: Be sure to use something as a cushioning gasket to insure a snug fit and to protect your truck lining. I used rubber or foam exercise mat cut to the same as the aluminum square tubing. Use a washer that a combination of hard plastic and metal to avoid the corrosive effects of dissimilar metals in contact with each other. last: My 26" full suspension bike fits, but I have swing it to one side slightly before i close the tailgate and lift the bike up and slide it down....It's a very snug fit but the suspension adds pressure to the tailgate and its works out very well. Or you could just use a tailgate extender.
Referring to special mounting instructions if you have a bed liner: (line #3). I do not have a bed liner, but I do have a molded plastic cap on my bed rails ('04 Ford F350). The first install over the plastic cap the locking pin or pin as called out in line #3 was nowhere near making contact with the metal lip of the metal bed under the plastic. What I did next on the second and final install was remove/cut away the plastic on the inside of the bed rail to allow the vertical portion of the "L" mounting bracket (Fig 4) to contact the metal bed. The locking pin is now at a position almost where it would protrude under the metal bed lip if I would remove the rest of the plastic under the horizontal portion of the "L" mounting bracket, I did not do that. After cutting a notch in the metal rail to accept the pin, the pin barely flushes out to secure the rack. A 1/4" longer pin would take care of this problem. One other thing that was not addressed in the install instructions was if you have a full size pick-up bed you are likely to attach the passenger side fork mount (Fig 2) to the right of the extension tube locking mechanism. The extension tube is a smaller diameter, so you will have resize the fork tube clamp (Fig 1) for the smaller tube. I can't explain how to do it other than it's a Chinese puzzle.
# 2
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
It works great! Easy, quick, you know. One needs to screw in the hitch bolt, for some reason, before latching it. Other than that, it makes going bike riding way easier.
# 3
Kuat NV 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Gunmetal Gray
This thing is built like a tank! It is of the best fit and funtion I have seen in a bike rack! Solid as can be, fits my bikes perfectly and looks awesome! Plus it folds completely out of the way to access the rear liftgate on my 2022 Rav4!
Great service from etrailer and the rack arrived as expected. Fairly easy assembly. OK video on Kuat’s site, but didn’t cover the foot pedal. Really glad we got the 2” hitch. It tightened up and we’re impressed with the quality and the stability of the rack. We haven’t done a road test yet, but look forward to putting it to the test. We have a Ford F-150 and it works great. The bikes were fairly easy to load with the batteries out and two people. We do need the strap extenders for our RadMini Step Thru’s. The tires are too big for the ones that come with. Only one set of extenders came with the bike and one adapter for a smaller tire. It’s okay, but since it’s a two bike unit, would have been nice to have both extenders. Otherwise, we are really liking the look and stability.
# 4
Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Gray
So after much research into bike racks, I decided on pulling the plug on the Kuat Sherpa 2.0. I've looked into the Kuat NV and other brands, but they were just too much for my needs. If you've got "regular" bikes and not the heavier eBikes, then this rack is perfect. I wanted a hitch rack that was user friendly and not overly complicated. I have a mixed bag of bikes and this rack can handle them all, from mountain bikes, street bikes, and BMX bikes. I like that this rack comes with an adapter piece for 20"-24" wheels. Assembly of the Kuat Sherpa 2.0 is really a no-brainer. I think it's only 4-5 bolts really. Everything else is ready to go. The anti-rattle hitch ball mechanism is simple to use with just a twist of the dial, easy. The tilt pedal/lever is also easy to access should you need to open your hatch, a solid "click" assures it's in place. So far, loving this rack. Fit and finish is superb. Thanks to Jerred and etrailer for answering my questions, always helpful.
OMG!! I have been researching and pricing bike racks for a month. Every time I thought I was ready to pull the trigger, I have a question or review that through me off the trail. I was ready to purchase the rack from outdoor retail store and drive 2 hours to pick it up from store to save the $75 shipping, when I thought about etrailer that I had used when I had a travel trailer. Checked them out, they had the exact rack I decided to buy, with $[XX] discount and free shipping. Life doesn’t get any better. It was delivered right on time and in great shape. BTW etrailers website description and videos were better than the racks manufacturer site. You are Rock Stars in my book. Overall, start to finish was above and beyond expectations.
# 5
Kuat NV 2.0 Base Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Matte Black
I've taken this rack all over New England on the front of my Dodge Ram 3500 pick up truck with a truck camper. I had no idea it was possible to love a bike rack so much. After one drive I didn't ever worry about it again. So nice that it locks up when I am camping or taking a quick stop for food on the road. So glad I bought it from etrailer. They totally help me pick the perfect rack for my challenging set up.
Still very new, but what an awesome bike rack! Assembly was a snap and the rack is rock-solid when you secure it to the hitch receiver. etrailer was amazing too - excellent communication, price and fast, free delivery. Overall I am extremely happy with the rack and service!
# 6
RockyMounts BackStage Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
We love our RockyMounts BackStage Bike Rack. The fact that it can hold our two e-bikes and swings out for rear door access makes it perfect for vanlife. Service and communication from etrailer is outstanading!
etrailer.com asked me for a review about 1 week after it arrived. A better review would be in about 6-12 months after delivery to allow me time to use and experience the rack. Disclosure: my review is just for the assembly and install. Assembly is not easy. I needed to go to the internet and look at photos. The instructions lack detail. So only 4 stars for assembly instructions. It seems like a good design. The included locks seem cheap - like why bother including. The hitch pin design seems to tighten down the rack so there should be minimal rattle and movement. The rack sits up relatively high, so it would be safer to lift heavier e-bikes with two people or use some type of field engineered ramp. Wish it was made in the US and I wish the country of original was fully disclosed in the etrailer.com description. Perhaps it is disclosed but I learned it was from china after it was delivered.
# 7
Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This bike rack works great for our 2 Lectric 2.0 e-bikes. We mount it on our 2019 Honda Ridgeline. It folds up nicely when it’s on the truck and we are using our bikes. The locking mechanisms work well also. I contacted support for a smaller hook arm to clamp B over the bike frame. They knew exactly what I needed and shipped it - no problem.
I've been using this bike rack alongside a trailer hitch I got here for my small car (chevy bolt ev) and it was exactly what I was looking to get to haul around my fat tire mountain bike bike. Sometimes I throw two bikes on there (either an e-bike, slightly heavier at 60 lbs, or a 2nd mountain bike) and it's perfect.
# 8
Yakima HoldUp Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Works well for transporting two 29" wheeled mountain bikes. However, after one year it's starting to rust in several areas (see attached photos), and the front wheel arms are becoming increasingly difficult to raise and lower. Finally the locking cable is extremely rusty as you can see in the attached photo. I'm not sure how durable this rack will be long term.
We have had this bike rack for one year and use it every week-end. My wife has a Trek e-bike (52 lbs) and I have a regular Trek hybrid (23 lbs). The rack is very sturdy and I have no issues driving at highway speeds, there is no movement of the bikes. Very easy to load and unload.
# 9
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 10
Rhino-Rack Bike Rack for 2 Bikes - 2" Hitches - Tilting
I purchased this bike rack a year ago and I use it A LOT. I had to buy and install a stabilizer because without it, the unit would sway back and forth even without a bike on it (very noisy). This makes removal more cumbersome but since I keep the hitch on year round it doesn't matter to me. The tilting function is fabulous allowing easy use of my RAV4 hatchback. I can even tilt it down with a bike on it. I got the 2 bike hitch. Plenty of room for two bikes to fit without rubbing. Lastly, the hitch has a sizable through-hole on the bottom to thread a good sized cable so I can lock my bike up. Sturdy. I highly recommend.
The unit ‘s simplicity is a real plus. It takes less than 3 minutes to put the rack on the vehicle. It is well built and very durable and has a nice feature that allows you to open the rear hatch for SUV owners without removing the rack.
# 11
Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This is a great product and works beautifully! The only issue was some sloppily made plastic turn knobs that were cross threaded on arrival. However, Yakima immediately shipped out replacements. It carries two large E bikes easily. They fasten solidly and are easy to load and unload!
etrailer: prompt delivery, fair price! Rack: It does fit my (2) Gazelle T10 eBikes. 1) I found I had to adjust every setting to get bikes to fit. Until you learn there are many adjustments, it does not seem like the center/vertical clamps will reach both seat posts. 2) The ramp is barely usable; my wheels are max it will fit and you must have at least 12ft of clearance on each side of car to get bike lined up with ramp. 3) My bikes have a "walk" feature, this is not usable as its too awkward to hold the walk button down and move around the rack. I found its easier to abandon the ramp and load front then rear wheel. I will rig up a wheel stop, on ends of each wheel holder so bike will not roll off while I strap it in. 4) Rack did NOT come with a lock for hitch pin; this is very disappointing as they say in manual this is an optional item. Every rack I have seen at least has a clip that would otherwise hold the hitch pin in if somehow the bolt loosened up. 5) The rack weight is the lightest I have found. 6) You must load the first bike (closest to car) from car passenger side. This will avoid you bike pedals hitting the vertical bar. That means you must load the 2nd bike manually as there is no way to get the pedals past the vertical bar. I will get used to this, I hope. 7) The rack is a few inches above the receiver (part that goes into hitch) so if you have a low hitch this might be an issue with ground clearance. With both bikes mounted up, it seems very stable and hopefully will be secure in travel.
What our customers are saying:
"I ordered a trailer hitch and a bike rack carrier the order was shipped with in three days. To put the hitch on only took about 30 mins. only had to drill two 1/2 holes. fit like a glove."