# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original. My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side. The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done. I already have a winch mounted on a hitch bracket, but may use this for more things besides that.
It wasn't fun to install by myself, but managed to do it in a few hours. Worked out great so far, I've hauled motorcycles on hitch carrier for about 2k miles so far and had no problems.
# 2
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Ordered the same hitch from Amazon, and showed up not J-Pin ready, with (1) hole drilled for a hitch pin against the weld. Can't run the nut flush because of the interference with the weld bead, and no 7/16" hole present. Returned it. Ordered another one from etrailer direct. Called in the order to make sure they QC'd prior to shipping. Assured me they would. Box never opened, and the same nonsense showed up. Not happy, trying to work it out.
Fit Perfectly, super easy to install, and super fast shipping! Holds Hollywood Bike Rack Great and very solid for my two E-bikes. Thank you etrailer!
# 3
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This has been a great purchase that has enabled me to maneuver my trailer better in the space I need to park it in my backyard off a fairly narrow alley. I installed it on the front of my '98 Dodge Ram 2500 4x4 V10. It is stout and secure and was not too difficult to put on. I think most of my installation issues were factors of my truck's age, or mine, but who knows. As I recall, I had to attach bolts in a particular order so that the holes would line up right and I wasn't sheering the threads. After I figured out the order it snuggled up great and feels as solid as if it were factory installed. My front plate bends a bit at the bottom to compensate for the receiver sticking out, but no so bad as it isn't readable. It does not stick out much more than the bumper so I have not run into it when walking across the front of my truck. I love it to push my trailer in to my yard and I can't wait to put a boat in the water with it. I would buy one again, if I were to ever get a different truck...but why would I do that?!
My front mount receiver hitch for my 97 Dodge Ram came in perfect shape and in a timely manner, the installation went very smooth and instructions were very easy. Only thing I recommend is a little longer sway bar bolts would be nice, just a little hard to get started. Other than that perfect easy company to work with and shipping was great I will be using etrailer for future purchases thank you!!
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It was very easy easier than I thought it took me less than 30 minutes I took advice of someone else who purchased one and installed it they recommended taking off the bumper which which was also quick and easy. I'm in New York and it arrived in 3-4 days.
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 7
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
Terrible, they sent the wrong hitch and now want me to pay shipping for the return
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I ordered this unit after sending one back from a different supplier ,the previous one said it fit my Ranger, well after getting it and checking installation video`s it needed to be cut up and fafbricated, no thanks. The Draw tight from E-trailer fit great,delivery was prompt even with a major snowstorm ,the only hic-cup was I didn`t take off my front bumper,due to a brush guard we welded on years ago but even without taking off the bumper I was able to get it on , heck I didn`t even jack up the truck. A little trim on the bumper trim and some help from my motorcycle jack easy to do , took about an hour and a half looks good , fit great, now its time to attach the snow plow and get my driveway clear.I am also ordering the air bag spring helpers for my little truck and will see how that goes too, thanks to the staff at E-trailer, I`ll be ordering from you again.
Ford ExplorerThis is a great addition to my old square body Explorer Sport, the closest thing I can afford to a square body Bronco. Great for moving trailers around the yard or put a hitch mounted bike rack up front and tow your boat or camper behind. Best part was no drilling direct fit and in stock at etrailer!
# 9
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I installed this myself with no help and I'm rapidly approaching 70. All the parts were included. Yes, it took me a bit longer, and, yes, it wasn't fun laying on the ground or getting up and down from such positions. The hitch works as it should. Some of the bolts were a bit inaccessible for my torque wrench with the various extensions I own but I'm sure they're very tight. It works great with my snow plow. Sorry, but I have not taken any photos.
Overall everything went well. The box arrived with a few holes in it, but the hitch and all bolts were there and just a couple of minor scratches. Installation was pretty much straight forward, a little more difficult on the ground as opposed to doing it from a lift but that is generally accepted by do it yourselfers. Tool list is more extensive if you torque the bolts properly, for instance you will need a crows foot that fits your torque wrench as you can’t get a socket on a couple of the bolts. I’m a tool crazy person so that is no problem for me! I preferred the Draw-tire brand as I could put the rock and gravel Shield back on my 2010 Toyota Tacoma. Looks good fits great and etrailer.com did a great job of delivering the product at a good price. Thanks etailer.com!
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Toyota TundraThis was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
Straight forward and perfect fit on my 2008 Toyota Tundra!!
# 11
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.
The hitch was easy to install. The only issue is who ever welded it put the front ring on and it's turned to one side. It functions fine but bothers my OCD.
# 12
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.
I plan on installing it tomorrow, however first impressions are not good. The box it item was shipped in was extremely damaged. Torn, ripped and taped up on all sides. The delivery person said that due to the sharp edges and the face it wasn't secured in the box (lose) led to the damage. It appears the item was not packaged properly. I just hope all the parts are there. More to follow.
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.
I chose this product because it was among the more inexpensive front hitches I could find. I plan to build a t-bar for it and use it in conjunction with a homemade headache rack to carry 16 foot garage doors. Like other reviews and vids I have found, the bolt up is hard. I reversed the bolts and use the new ones on the outside, as well as removing my grill. My truck is a 2003 - so not much room like the 2008 and newer trucks.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
I ordered this literally less than 24 hours ago and it arrived to my doorstep!!! I think etrailer needs to call Amazon and tell them how it is done. Like honestly, I am not even prepared to put it on yet as I was expecting a week for delivery! Holy cow, do you all sell groceries as well?
# 15
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.
I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.
# 16
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2002 Chevrolet SilveradoThe hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.
Just received the hitch receiver today (no pun intended). Very easy, precise, 4 bolt assembly into the existing frame. Took about an hour to install for a non-mechanic like me. I really appreciate the versatility that I now have to put different attachments on the front of my truck. Note the ball and step in the pictures. Being lifted 6 inches, even I, at 6 ft 4 in. can't access the motor without the step. I plan to put a carrier on the front and carry a small motorcycle or bicycles when we are on our annual Arizona Snowbird excursion. In appreciate well built, well thought out and executed items.
# 17
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The packaging needs additional crush protection. While it’s difficult to damage a trailer hitch, the box was mangled and the hitch is missing paint and has jagged edges of flaking paint all over. I’ll spend time repairing the finish on the hitch after paying good money for what should’ve been a product in brand new condition.
Perfect fit on my 2020 Chevy 2500HD. I didn't even have to trim the lower plastic spoiler. Install took about 20 minutes. Can't wait to try it out for my motorcycle carrier. As always, etrailer gives great, speedy service.
# 18
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It installed as advertised and fits perfectly. I haven't used it yet, but it will make positioning my trailer in my backyard much easier!
Would like to just take a moment To thank etrailer for getting our draw tight front mount hitch and our swagman bike rack to us. It certainly solved our problem. For sometime we have wanted to take bikes camping with us and have not had a proper place to haul them. The camper has a molded bumper and I certainly didn't want to haul them in the camper. So my hat off to you on both products
What our customers are saying:
"I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future."