# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original. My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side. The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done. I already have a winch mounted on a hitch bracket, but may use this for more things besides that.
It wasn't fun to install by myself, but managed to do it in a few hours. Worked out great so far, I've hauled motorcycles on hitch carrier for about 2k miles so far and had no problems.
# 2
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Ordered the same hitch from Amazon, and showed up not J-Pin ready, with (1) hole drilled for a hitch pin against the weld. Can't run the nut flush because of the interference with the weld bead, and no 7/16" hole present. Returned it. Ordered another one from etrailer direct. Called in the order to make sure they QC'd prior to shipping. Assured me they would. Box never opened, and the same nonsense showed up. Not happy, trying to work it out.
Fit Perfectly, super easy to install, and super fast shipping! Holds Hollywood Bike Rack Great and very solid for my two E-bikes. Thank you etrailer!
# 3
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This has been a great purchase that has enabled me to maneuver my trailer better in the space I need to park it in my backyard off a fairly narrow alley. I installed it on the front of my '98 Dodge Ram 2500 4x4 V10. It is stout and secure and was not too difficult to put on. I think most of my installation issues were factors of my truck's age, or mine, but who knows. As I recall, I had to attach bolts in a particular order so that the holes would line up right and I wasn't sheering the threads. After I figured out the order it snuggled up great and feels as solid as if it were factory installed. My front plate bends a bit at the bottom to compensate for the receiver sticking out, but no so bad as it isn't readable. It does not stick out much more than the bumper so I have not run into it when walking across the front of my truck. I love it to push my trailer in to my yard and I can't wait to put a boat in the water with it. I would buy one again, if I were to ever get a different truck...but why would I do that?!
My front mount receiver hitch for my 97 Dodge Ram came in perfect shape and in a timely manner, the installation went very smooth and instructions were very easy. Only thing I recommend is a little longer sway bar bolts would be nice, just a little hard to get started. Other than that perfect easy company to work with and shipping was great I will be using etrailer for future purchases thank you!!
# 4
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I finished installing my new front hitch a few weekends ago. All in all I'm very satisfied with the new hitch, primarily as it solved a long standing problem and the right price. The construction and fit of the hitch is excellent. It does take a bit more than an amateur to install however, so below are my comments with photos attached to help the next guy: 1.) Front bolt - The existing hole on the frame it too small to accept the new bolt. This needs to be drilled out (only with a 90 deg. Drill), or replace the existing bolts in the opposite direction...which is what I did, (photo 3). 2.) Middle bolt - The existing frame hole does not align with the hole on the hitch. You need to dry fit it and mark it and cut an approx. 1/2 - 5/8" chip out of the frame. 3.) Rear bolt - Rear bolt ends up with about a 1/4" gap between the frame and hitch. I shimmed the gap and torqued it snug. There's also no way to install the internal washer, without losing your sanity. I eliminated it and used a vise grip on the bolt end as I tighten the nut. Additionally, you have to remove the bumper kicker brace to install this rear bolt. Once the hitch is up, there is again no way to reinstall that kicker brace without disassembling the whole assembly at the bumper. My problem with that was that my existing bolt were old and rusty and probably won't come off or go back on easily. Instead, I fabricated an extension bracket and reassemble that kicker brace just above the new bolt (photo 2). - Photo 1: Before install, after removing lower spoiler - Photo 4: After install, before cutting and reinstalling lower spoiler
2001 2500 sport fit on the frame was perfect with no drilling. Had to notch the cover and metal support at the bottom but would rather that than hang to low.
# 5
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It wasn't hard to install, instead of the wire I used two pen sized telescoping magnets to wriggle them in the square holed plates. My plans are to use this hitch in place of tow hooks. Good looks and sturdy!
I didn’t know how much I would need this until I moved into my new house just yesterday. The garage door is much shorter at our new house, 7 foot vs. 9 feet. Using the front hitch and a 5 1/2 drop hitch, I have about two inches of clearance when putting my boat in our new garage. Without the front hitch I would have been able to get the boat in the garage. Not to mention how much more the trailer is to steering inputs, the garage is much narrower that our old one. If you have a tight spot to park something this will make your life much easier! Installation was simple and instructions well written. The tool to install the mounting bolts is a brilliant idea.
# 6
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
For my 2005 Ram 2500 4WD. This product is well made and I am looking forward to using it for a winch that can go on the front or rear of my truck and may get carrying racks, etc. I believe the product I received was damaged in shipping. The span between the flanges that bolt to the sides of the truck frame was about an inch narrower than the distance to the outsides of the truck frame where the hitch fastens to the vehicle. One of the flanges was badly out of square. I widened the gap by placing the flange in a vise and pulling on the end of the hitch till it was closer to square. Then I used a large crescent wrench to tweak both sides till the dang thing would go on. Then I still had to use a pretty big hammer to wack it into place. Also, this installation was very difficult for me to do alone on the ground. A buddy and a lift would have made this much easier. The included fish wires were super effective and high quality; once the bolts are in place just thread the wire through the mounting holes in the hitch as you lift it into place. Went much easier than I expected. Instructions say use a hole saw, I used a step drill bit and that worked well, except for the small burns I got from hot chips raining down
My particular model of vehicle (03 Dodge 2500 pickup) was a very easy install. I am very happy with the Curt Front Hitch. Now I can easily mount my winch, bicycle rack and a cargo hitch to the front of my truck.
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I got the hitch and made a appointment to have it put on. That fell through so I decided to tackle it myself. It was extremely easy, my wife helped hold it in place while I got the bolts started. I use the hitch which I install in the front of my 2500 Ram to haul my ebikes on a bike rack. Works excellent.
I was totally amazed at the quality and the fit to my truck this hitch went on so easy even though I have a brush guard on this truck also. This item went on in about 45 minutes and that was to unpack it and get out the tools start to finish.
# 8
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
If I could mark it at 4.5 stars I would. I like it the hitch. I think it hangs down too low, only 8" off the pavement. I did not like to have to take off the tow hooks to install the hitch. I did like the idea of I sold the tow hooks for almost as much as I paid for the hitch. I had to buy a hitch extender. ( I do not see the extender I bought on etrailer listed any more.) The extender put the hitch out far enough to clear the grill guard that I had installed. My goal was to have a place to mount my 8,000 pound winch. I can now slide the winch in the front receiver or the back factory receiver. I can now pull the truck out from either front or back.
This front mount hitch was just what we needed to haul our bikes when camping with the slide in camper. We had to take the bikes and a bike hitch off each time we had to get in the camper when we stopped. This front mount hitch saved us from having to do that. Also use it for a carrier to carry extra luggage. It came fast and it was very easy to install, just as advertised.
# 9
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It was very easy easier than I thought it took me less than 30 minutes I took advice of someone else who purchased one and installed it they recommended taking off the bumper which which was also quick and easy. I'm in New York and it arrived in 3-4 days.
# 10
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 11
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Overall I love the front hitch and it's fit on my 2017 RAM 3500. There's been some reviews talking about the packaging and also about the installation, so here's my experience. The box was sturdy and was shipped via UPS. It arrives undamaged. There was some extra carboard added across the top of the box presumably to help protect the receiver. When I opened the box I noticed that one of the brackets was slightly bent. I thought this may have happened during shipping, so I placed the receiver in my bench vice and gently brought it back to square. DON'T DO THIS. It appears the slight bend in the bracket is intentional. The receivers fits very snugly to the truck frame so that bend it to make installation easier. When I tried to install the receiver it was so tight I could not get it up into the truck frame. I ended up bending it back out of square (about 1/4" on each side). After I re-bent the brackets slightly it fit great. When you torque down the blots the brackets come back to square and everything was perfect. My only minor criticism is with the instructions tell you to cut out a portion of the lower plastic deflector on your truck. The instructions tell you to cut a piece that is 4/25" wide. It doesn't need to be that wide for this truck - it could have been the same width as the 2" receiver. It's not a huge deal, but if you want a really tight fit on your deflector, then just cut it smaller. The whole process, including the extra unnecessary bracket bending, took me about 2 hours to complete on my own. I used jack stands to support the bracket during the install, but an extra pair of hands would have made the process much quicker.
This hitch is definitely heavy duty and mounts securely. It does not block airflow to the radiators or interfere with the bumper proximity sensors. It deserves 5 stars from that perspective. But I give it 4 stars because unfortunately the distance between the side plates was 3/4" too narrow to rotate into place. It would not clear the frame rails, brackets, and spacers. Actually it wouldn't even clear the frame rails alone. My son and I read the instructions many times and experimented with every possible angle (which is a major hassle while supporting the hitch under the truck) and finally took the matter into our own hands. We used a high lift jack situated between the side plates to bend them outward. Then the hitch fit perfectly. Getting the bumper lined back up was another headache, but not because of the hitch.
# 12
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
Terrible, they sent the wrong hitch and now want me to pay shipping for the return
# 15
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Product was received in very good condition and quick. It took me about an hour from the time I put it on the ramps till I backed off with the factory tow hooks removed and the new hitch installed. Fit was as good as anyone could want.
etrailer is a great company. Smooth fast shipping. The hitch mounted perfectly.
# 16
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.
# 17
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I ordered this unit after sending one back from a different supplier ,the previous one said it fit my Ranger, well after getting it and checking installation video`s it needed to be cut up and fafbricated, no thanks. The Draw tight from E-trailer fit great,delivery was prompt even with a major snowstorm ,the only hic-cup was I didn`t take off my front bumper,due to a brush guard we welded on years ago but even without taking off the bumper I was able to get it on , heck I didn`t even jack up the truck. A little trim on the bumper trim and some help from my motorcycle jack easy to do , took about an hour and a half looks good , fit great, now its time to attach the snow plow and get my driveway clear.I am also ordering the air bag spring helpers for my little truck and will see how that goes too, thanks to the staff at E-trailer, I`ll be ordering from you again.
This is a great addition to my old square body Explorer Sport, the closest thing I can afford to a square body Bronco. Great for moving trailers around the yard or put a hitch mounted bike rack up front and tow your boat or camper behind. Best part was no drilling direct fit and in stock at etrailer!
# 18
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!
VERY Easy install - not quite centered but that's no biggie - Used it already to fine tune the travel trailer into it's tight parking space. Also will be used for carhauler/utility trailer parking and canoe hauling and bike hauling and winch mount - Multi use deal! ; )
# 19
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I installed this myself with no help and I'm rapidly approaching 70. All the parts were included. Yes, it took me a bit longer, and, yes, it wasn't fun laying on the ground or getting up and down from such positions. The hitch works as it should. Some of the bolts were a bit inaccessible for my torque wrench with the various extensions I own but I'm sure they're very tight. It works great with my snow plow. Sorry, but I have not taken any photos.
Overall everything went well. The box arrived with a few holes in it, but the hitch and all bolts were there and just a couple of minor scratches. Installation was pretty much straight forward, a little more difficult on the ground as opposed to doing it from a lift but that is generally accepted by do it yourselfers. Tool list is more extensive if you torque the bolts properly, for instance you will need a crows foot that fits your torque wrench as you can’t get a socket on a couple of the bolts. I’m a tool crazy person so that is no problem for me! I preferred the Draw-tire brand as I could put the rock and gravel Shield back on my 2010 Toyota Tacoma. Looks good fits great and etrailer.com did a great job of delivering the product at a good price. Thanks etailer.com!
# 20
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I have had the front receiver hitch installed on my 1996 Suburban for about a year now. I have a 12000 lb winch installed using that receiver hitch. I have gotten stuck twice and had to use the winch to extract the truck. Very glad that I have the front receiver hitch as it made putting on the winch very easy. Also useful for mounting a receiver mount bicycle rack to the front as well.
Product was shipped promptly and arrived a few days later. Packing was good for a heavy item with pointy edges, no issues breaking out of the box. Installation on a lift took about 30 minutes on my 1999 K2500 Suburban. The bolts were long enough to allow for my tow hooks that were already in place. A bolt stringer to pull the rear bolts from the top (inside the frame) is provided along with nuts, the other four just replaced the stock bolts that I had that mount from the bottom into tapped frame metal through the tow hooks. Curt makes great quality stuff. Clearance was reduced a little but I'm not concerned about it.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."