# 1
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 2
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Excellent customer service & support! Bought for my 2013 Honda Fit and plan to trailer my Yamaha Tenere motorcycle around North America! Very happy with hitch.
Typical quality of...VERY good!! Lol. I've pulled my small mc trailer numerous times with this hitch and NO issues!!!
# 3
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 4
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works perfectly. Fast shipping. Very Satisfied.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 5
Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
The hitch is exactly as described on etrailer. The drop measured exactly 9-1/4" as I wanted it to be. Curt rounds this measurement up or down to a whole number, 10" in this case. That is way off when you want your trailer and truck towing level are looking for a particular drop. Thankfully etrailer measures these themselves and show you where they are measuring from so you know what hitch to ask for.
I neeed to pull a trailer with my 2019 GMC Yukon. I found Etrailer.com and followed the instructions on determining the drop of the hitch, the instructions were spot on. I hooked up my trailer to my Yukon today, all was level and worked perfectly. I had driven around to Napa, Lowe’s, Home Depot and Walmart, and nobody had the 9” drop hitch I needed. Came back to Etrailer, bought the 2” ball and pin, and the Curt 9” drop hitch. I received the items quickly. Great website, Thanks, Craig
# 6
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!
# 7
Draw-Tite Ball Mount - 6-3/4" Rise, 8" Drop - 10" Long - 5,000 lbs
Just as advertised and solves my problem of trailer tongue level to hitch position. Delivered on schedule with no hiccups. Fits perfectly in the 2" factory receiver on my Jeep JKU. The 2" ball in the picture is a reused one not new which is why it has rust on it.
I placed my order at 11:24 am Monday. At 1:07 pm, I was informed that it had shipped. Furthermore, though I requested Standard shipping, George went ahead and sent it Express. I got my ball mount today, three days after I ordered it. Now if that's not the way business should be done, then what is? I'm all about getting the job accomplished, sooner the better, and etrailer.com is my kind of company! I have bookmarked their site, and I won't hesitate to shop with them again. BTW, the ball mount does exactly what I needed done, my boat trailer is nice and level now, not pointed at the sky like before!
# 8
Draw-Tite Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 8-1/2" Long - 16K
This is a beast of a drawbar, solid forged steel & well finished. It's also very heavy and E-Trailer needed to ship 3 times because the first two broke out of the box they were packed in. (Someone in the USPS has a couple nice draw bars.) Fortunately the 3rd effort was much better packed in a reinforced box and was successfully delivered. E-Trailer customer service was exemplary in resolving the shipment issue & I will definitely shop with them again.
I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.
# 9
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 10
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 11
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
# 12
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Package was delivered empty ... see photos
# 13
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 14
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Haven’t used it yet, but looks good. I’m not sure what height offset I need, so this kit gives me several options, plus two ball sizes. Really good value.
Ball mount kit arrived quickly (within a few days) upon placing order online. Parts were shipped loose in box and bottom flap on box was open when received. Fortunately, all the parts were still in box and in good condition. Kit includes ball mount hardware I need to pull trailers with different hitch heights.
# 15
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.
Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.
# 16
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
This drawbar was clearly used. See the picture. I asked etrailer about it and sent this picture but the person that replied, Noah, thought it must have been bumped around in shipping. If shipping caused this much damage, it's a poor quality product. If it was, in fact, used, then etrailer lied to me. Either way...not good.
# 17
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 18
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
Great product for getting out past the tire carrier on a small SUV. Customer service was wonderful with great follow through and any assistance I needed I will definitely use etrailer agin
# 19
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 20
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
What our customers are saying:
"Quick processing, and delivery. reasonably priced very satisfied"