# 1
Ultra-Fab Ultra Scissor Jacks - 24" Lift - 13,000 lbs - Qty 2
Definitely a heavier duty version of our campers stock stabilizers. They bolted right up to the brackets and glad we have new stabilizers. I hope the paint lasts on these as that seems to be an issue with the other, cheaper stabilizers. Time will tell.
if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.
# 2
Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 1
Gave it a three due to the modifications that had to be done to make it fit. I had to grind down the outside of the pad about 3/16" to make the stabilizer fit up into the bumper of our Scamp. In addition, I shimmed the top down about 5/32 so it would lock into place without forcing it. One stabilizer had epoxy which looks very sloppy. This on the edge where it should be spot welded - hope this is the case! Fortunately, I'd read reviews indicating that this was not a direct replacement for Scamp 13'ers. Folks should be aware they may have to do some work since the stabilizers may not fit out of the box. Once modified, they work as expected.
I drilled two 3/8" holes in the top of the rail and used two stainless bolts to hold it on. Works very well for this application. It folds and holds the trailer for loading, and if I have to leave it somewhere, and don't want the tongue sitting on the ground. I used it on a Harbor Freight 4x4 trailer I am building to pull with my Can-Am Spyder. Love it!!!
# 3
Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
Easy to install both in under an hour. Provide good stability to small (boat) trailer when deployed. I can see the paint/powder will be as durable as they were as simple to install
Bought these for my cargo trailer. Did not get around to installing them for several months. When I finally unpacked them, the “foot” of one came off while I was unwrapping them. I had to drill holes and add a few screws to reattach. There was no damage to the box. They still serve their purpose, just disappointing.
# 4
Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
Beautifully made and a solid drop leg. Do I need to say more? You get what you pay for.
Product was exactly what I was looking for. Only issue is the one square latch pin is missing.
# 5
Leveling Scissor Jack Set - 30" Lift - 10,000 lbs - QTY 2
These jacks are solid and easy to install. Do not come with mounting hardware. I used 5/16” x 1.5” bolts with washers and lock nuts. Also added some locktite to be sure they don’t come loose. Standard attachment on most trailers seem to include one or two bolts, then the rest with self tapping screws, which isn’t very secure in my opinion. I had to drill out some of the smaller holes to fit the 5/16” bolts but an easy job for a DIY project. Thanks etrailer for selling a great product and quick delivery.
Products and people are great I’ve ordered hitches axles and or it rams ships fast and never an issue thanks
# 6
Ultra-Fab Ultra Scissor Jacks - 30" Lift - 13,000 lbs - Qty 2
Didn’t last 3 months the end came off and screw mess up where the jack don’t work anymore
Worked beautifully for a Replacement for our customer
# 7
Ultra-Fab Ultra Scissor Jack - 24" Lift - 6,500 lbs
Replacement jack fit and worked perfectly Fast delivery
Jayco camper came with stabilizing jacks in the rear but none in the front. After wife complained that my walking around in the camper in the morning made the bed feel like a water bed I installed these jacks. They work perfect, easy and fast to deploy and camper is now solid when parked.
# 8
Leveling Scissor Jack - 24" Lift - 5,000 lbs
Much better jack than the one that came with the tow trailer. This 70 year old woman had no difficulties installing it. One year later still works great!
leveling jack was delivered very promptly and in good shape. installed on my 5th wheel easily and works fine. a bit lighter duty than the OEM jack but darn good value for the price and will get the job done. etrailer is the best!
# 9
Stallion Stabilizer Jacks - 7" Drop Leg Travel - 22-1/4" - Qty 2
I mounted this Stabilizers Jacks to the back of a 4x8 utility trailer. I use the trailer to haul my Honda ATV to MotoAmerica motorcycle races. Once the ATV is removed I lower the jacks and mount my tent inside the trailer. These stabilizers allow me to safely move around in the tent without fear of the trailer tipping.
Jacks worked great. Added them to an aluminum 2 place enclosed snowmobile trailer that did NOT like humans to walk up the rear ramp when unhooked and empty!? ...problem solved.
# 10
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
The product itself was great. It fit right in to the brackets from our old landing gear. We were able to use our existing motor as a cross fit with this gear. The gear box was even better than Lipperts as it was not plastic. The only issue we had with this was shipping. We ordered the part same day as our water pump because we were told it was in stock. Low and behold they changed ship date numerous times, with the excuse it was not easy to pick. Anyhow, two weeks later we finally got the part we ordered.
I have a 2000 komfort 26FS. It has original landing gear that was made by Atwood.Parts to repair are apparently no longer available. Did alot of research and this kit seemed to be a good replacement. It is a exact replacement. Took some time to get it installed as my 5th wheel has a wall and frame right next to landing gear. Original motor bolted up with replacement of original screws which were half inch to short. Four days to get delivered to Oregon. I would have given a five star review but I was missing square tubing that runs from gear box to other leg. Tubing is clearly pictured in discription photos.
# 11
Ark Drop Down Corner RV Stabilizer Jacks - 24" Long Corner Steadies - Silver - Qty 2
The box was a little beat up but, after all they are heavy steel parts and they are trying to keep the weight down for shipping coasts. The stabilizers were in great shape. I liked that the mounting brackets are removable and made it convenient to weld in place. The brackets could be bolted on but, you would have to countersink the bolts as there is about 1/8" clearance between the bracket and stabilizer body. I'm very happy with them and would recommend them. I would like to have etrailer show all the dimensions and capacities.
Replaced flimsy rusting scissor stabilizers w weldable mount Ark 24” Stabilizer, made paper templates for old mounting holes using center punch and drill press for the plates then replaced 5/16” bolts with 5/16”x 31/2” bail hitch pins for removing for boondocking on the washboard roads as they are heavy duty & mounted on an ATC aluminum trailer frame. Well built and beefy the zinc plated steel is better than powder coated sheet metal for rust control and a better looking rig
# 12
Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - QTY 2
work very well for portable leveling couldn't fix too Jayco Melbourne any where under RV. Still trying to figure a spot.
Received shipment next day after ordering...no added charges. Shipping package arrived in excellent condition. Scissor jacks look good and work smoothly.
# 13
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
Perfect replacement, works great, excellent shipping time and service. Just wish I had got the electric motor that goes with the legs.
Ordered this from etrailer instead of other sites as I knew the shipping would be faster. Sure enough I got the item in 4 days on Thursday and Installed it on Sunday. Very quick and easy. Took longer to get all my tools and set up items together than the actual work. The item was a exact fit with installation being feeding the legs through the holes in the floor down from the inside and installing the 4 clamping bolts to hold them in, the gear box on the lead leg and the cross bar and motor. Now it purrs like a kitten when activated instead of clanking and creaking and blowing fuses. Actual install time was probably 1.5 hours taking my time and injecting extra grease into the gears and lead screw. These replacement units have a grease fitting for both which is great and should allow them to last forever! Being a safety freak I used a 3 ton jack with a 4X6 placed long ways to catch the I beams under the trailer then placed 3 ton car jacks under the frame also and for extra safety backed my truck bed under the tongue for extra security while I worked. The price was crazy great, the fit was excellent and the shipping was fast as usual. less money in parts and 2 hours of work probably easily saved me a grand over taking it to a RV repair shop! Thanks etrailer. Saved me again!
# 14
Leveling Scissor Jack - 30" Lift - 5,000 lbs
This is the only jack I have found that is suitable for changing flat tires on my utility trailer. I only wish the jack were made in USA.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."