Best 2021 Chevrolet Malibu Watersport Carriers

Works great. I’m 5’6” and the pivoting cradles make for easy loading and off loading. I do need a stepping stool to install the carrier on the roof rack.

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This product was very easy to install. I had it installed in about 15 minutes and my kayak on the roof a few minutes later. The only issue I had was one of the tie-down straps was broken (stitching was not complete or something). Other than that, this product was great! The customer service (Carol and Neil) were great also, helping with the strap problem. Thank you again!

Click to Enlarge

Click to Enlarge

The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.

Click to Enlarge

Click to Enlarge

We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.

Click to Enlarge

My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.

Click to Enlarge

Very good quality materials for the price point. No tool Assembly and installation is a bonus. I’ve used them for two weeks now, hailing in both two kayak and single kayak configurations. The lever that you pull Up/down on is going to break. Period. If you have the rotating level too tight you can’t switch it up or down and if you have it too loose, it will come unscrewed and then you have a hard time longing up that no internal thread to get it back on. Also, it’s a pain to have to move the entire system to reconfigure needs. Would be nice if it had a slide and lock back in option once on the cross bars. Pulling off 16 wing nuts isn’t ideal. The video was great, appreciated that. Do wish they had shown how to tie down when using two kayaks because once you have one on the system when you place the second on the opposite side, you no longer have access to that center rack. Shipping speed was excellent. The quality of the cam straps is impressive. I have a hand injury and so getting the bolts secured was difficult. The fact that they come with two different lengths to accommodate different rack heights was really nice. Make sure you have your cross bars 24” apart as the instructions say.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This carrier has worked out really well! I paired it with the SportRack Semi-Custom Roof Rack for Naked Roofs - Square Crossbars, and the carrier attached to it perfectly. I drive a 2014 Honda Civic and this carrier has been able to transport two kayaks with no problems. Highly recommend, especially considering the price.

Click to Enlarge

Click to Enlarge

Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.

The product seems great but I have not figured out how to get it safely attached to my bars. I have an Agricover Adarac on the bed of my truck and the crossbars are 1-1/2 x 1-1/2 inches square. I thought this would work well since it's for up to 3-1/2 x 1-11/16" crossbars, but it isn't secure on these. I'm going to try and figure out an alternate method for attachment though. Thule Hull-a-port Pro's are the perfect (mounting) solution but don't seem to be made any longer.

Click to Enlarge

This product it great! The only issue I have had was with the brackets sliding slightly when driving on the highway, but it was nothing that an additional ratchet strap couldn't fix. Would recommend to anyone!

The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.

Click to Enlarge

First experience with purchasing from etrailer. Absolutely felt that my order was personalized which is a nice touch. The Rhino Rack S512 folding JStyle Kayak holders arrived boxed impeccably with no damage whatsoever and the price was great! Fantastic first time experience. Looking forward to using them. Thank you.

Click to Enlarge

As all Thule products the Thule universally mounted canoe carrier is great. It came with all required items for safe and easy canoe transportation. There are two straps with pull to fasten for the canoe down, two tie down ropes for each end with nice pull tight and release mechanisms for the cord as well, along with two straps to fasten to the canoe ends used with the pull to tighten cords. The Chevy traverse cross bar had to have the plastic end caps removed for use with Thule canoe carrier. This was because my canoe took up the entire cross bar width to allow for Thule mounts. It is not a big deal to remove the plastic end caps. They only provide a finished stream lined look. Happy and Safe Canoeing

Click to Enlarge

Click to Enlarge

Click to Enlarge

After retiring my 1999 Chevy Silverado 4x4 pickup, I purchased a 2017 Subaru Outback as a replacement vehicle. To transport my 1981 17 foot QT17C Alumacraft canoe on the factory installed roof rack crossbars that came with the Outback, I selected the Thule Portage Canoe Carrier w/ Tie-Downs - Gunwale Brackets - Side Loading - TH819 to do the trick. With one previous transport of the canoe sitting directly on the Outback roof racks, I realized those Outback roof racks were not as durable as the racks on my truck so I sought an improvement to avoid future scuffing and scratching. I did some advance research online and couldn’t be more pleased with this purchase from etrailer.com. I now have a quality product at the right price and these gunwale brackets are a simple solution for this veteran canoe man. The padded brackets grip the canoe and stopped the scratches. The high-quality load straps are nice with the rubber pad that covers the buckle and they easily snug the canoe tight to the racks. I’m also impressed with the bow/stern tie downs that have a very nice ratchet and clip on one end and I secured the supplied hook with a bowline knot to the other end of the ¼ inch rope. The Outback did not have convenient anchor points on the front or back of the vehicle for tie down locations but I found a good solution there as well by ordering the Thule Bow/Stern Tie-Downs - Qty 2 - TH530. This works well with the tie downs I mentioned previously. One limitation to be aware of with the Subaru Outback roof racks and this product is the width of your canoe. My 17-footer measures 34 inches at its widest point at the portage yoke. I had to place the four brackets up tight against the inside roof mounting to achieve the spread and accommodate the canoe placement. The canoe ended up fitting like a glove on the padded brackets. When placing the strap to hold the canoe down to the crossbars, I ran the strap through the vehicles tie down points and then under the crossbars for added security. Total product installation time including securing the canoe can easily be achieved in approximately 20 minutes. I look forward to many more years of safe and happy canoeing. I give etrailer.com an excellent rating for the entire ordering and shipping process on top of the high level of satisfaction with the products I purchased through them. Their customer service and price ensured me that I’ll do more business with them in the future.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It's doing the job of securing my kayak to my rackless prius, at a fraction of the cost. However, the instructions included along with the straps did not work for me. I spent a considerable amount of time adjusting things: the red straps that are supposed to go over the boat and secure on the bars were not long enough. The blue straps are much longer, so I am using the red straps to secure the bars to the car, through the open doors and cinched inside the car. I am using the blue straps to reach over the boat, and I decided to feed those into the car too- feels more secure than to attach them to the bars on top. The black straps for front and back strapping don't work for my car in the way shown, I had to jerry-rig. Overall I have figured out how to make it work, and I'm glad I didn't spend $xxx.xx on a serious rack system.

Click to Enlarge

It's reliable and very easy to install. Trapped several different kayaks onto roof and driven long distance at top speed and no issue with kayak getting loose or moving around.

Click to Enlarge

Click to Enlarge

've previously used the Yakima Kayak Stacker (old style), which worked fine but I always worried the straps would slip off the hook at the top while I was loading boats. They also didn't fold down, so had to be removed after use unless you wanted to look odd and cause a whistle while you drove down the road. They didn't have a universal attachment option, requiring adapters depending on the style and make of your crossbars. More recently I got the Thule "The Stacker", which is a superior solution. You thread the strap through a closed loop at the top, so you don't worry about straps slipping off while you're loading boats. They fold down after use and have a universal style attachment that fits around most styles and makes of crossbars. Good stuff. I really like the straps that come with these, as there is a rubber cover that slips over the metal cam buckle to protect your car's paint while you're tossing the strap over your boats to strap everything in. In order to shuttle our boats for river trips, we needed stackers to fit on both our cars, so it was time for another set. I had never heard of Rhino Rack before, but the lower price than Thile caught my eye, so I read about them and decided to give them a try. The Rhino Rack Nautical Stack used a closed loop at the top, which I liked better than the Yakima or Malone options, and came with the hardware necessary to install them into the C-channel of my Malone aero crossbars, which I wanted to try. I remember that with the Malone stacker, you had to buy the C-channel mount hardware separately. I really like the Rhino Rack Nautical Stack. They are a single post design, unlike the loop style of the Thule "The Stacker". I don't know if this cuts down on vortex drag, but it definitely saves you a couple horizontal inches up where the boats stack. The Rhino Rack Nautical Stack has textured rubber strips on either side of the post, which I believe is intended to cut down on vortex drag, but is also quite helpful in that boats tend to slip much less when you're just leaning them up against the post as you load up before you strap them. That's smart. The Rhino Rack Nautical Stack feels really solid. The mechanism for folding them down and locking them upright is easy to use and feels solid. Installation instructions were good. I tried to install into the C-channels without removing the rubber tubing in my Malone aero crossbars, but couldn't get the little squares to slide into the slots with the rubber tubing in place, so had to cut the tubing, slide the Nautical Stacks into place, then cut down some of the tubing I had removed and replace it in the remaining unfilled crossbar slot. That's not a knock on the Nautical Stack; just a tip in case you're trying to do the same kind of install I did. The one area in which I was less impressed was the tie-down straps that come with this kit. The metal cam buckles have no covering at all, so I'll probably still use my old Yakima and Thule straps instead and use these as backups. But overall, I think these are going to work at least as well, if not better, than the Thule option, and for quite a bit less money.

Click to Enlarge

Click to Enlarge

So much better than the 'C-shape' kayak holders. These things allow you to fit inside a garage, and add up to four kayaks. Very easy to use.

Rec'd earlier this week, so today i will install. The item was obviously a return. The logos are nearly scratched off in places, all the items were loosely thrown in the box, and the 10mm wrench and hex key were missing. i think everything else is there. The keys should be a bright color instead of black, some spray paint will fix that. Anyhoo, i am a little disappointed.

I mounted it on my Yakima racks. Very easy to do (directions could really be improved by having someone describe the steps more clearly). I have not used this. Could be a month or so. However, initially, it looks good. Too bad the angled arms that hold the kayak are not adjustable depending on the angle needed.

I really like these j-style folding kayak roof rack mounts. They are very low profile and I am able to leave them on while I drive a standard 5th generation 4Runner through a standard 7 foot garage door.

I rarely leave reviews but I have ordered a few items from etrailer lately and will say that I am impressed with how quickly they get my order shipped and how quickly it gets here.

Brought home a new kayak yesterday using this J cradle for the first time. Easy to set up and load. Two complaints: not impressed with the strap buckles - had to tie knots to secure. And the 3-inch bolts weren’t long enough to easily attach the cradle to my Rhino Rack crossbars, so I had to replace them. Also got my finger pinched pretty good adjusting the cradle knobs - my fault for not being more careful, but just saying …

Click to Enlarge

Great product for the price - The cradles were very easy to mount (and lay flat once folded). The videos were helpful in showing how to set the straps in the most efficient way. I test-drove my car today with my fishing kayak on top on a 80-mile round trip (a mix of freeway, country road and dirt tracks). The kayak was perfectly still, no particular wind noise and I was able to muscle to kayak up the roof and take it down on my own (it's a 52 lbs boat). I really recommend that product and I'm glad I went for J-Style cradles!

Click to Enlarge

The product arrived in a timely manner with specific information as to where it was all of the time. There was a credit card issue in the initial order and when I called I was pleasantly surprised to talk with a person who expressed sincere interest in my experience with the company The product is of high quality and is heavy duty, something which I was concerned about. It exceeded my expectations.

Product arrived in timely fashion as advertised. Easy to install. Perfect for my two kayaks.

Best solution i could find for a 95# 12’ fishing kayak for a F150 with a roof rack (i have a thule removable). It performs really well. Only complaint would be rubber coating on brackets that go under the truck rack rail cracked so i worry ot may come off with age. I still recommend this. I pull a travel trailer so I couldn’t use a bed extender & the roof was my best solution.

Click to Enlarge

I am very happy with this purchase. I ordered two sets to hold my two large ocean kayaks on my roof rack. The kayaks are approximately 34” wide and I was concerned how sturdy the mounts would be but the reinforced plastic feels very durable and accommodated the width of my kayaks easily. Mounting to my Yakima aero bars was no problem with the hardware provided. I used the longer screws and there was plenty of length to thread on the nuts and the screws have plenty of clearance from my roof. The included straps are also of a heavier webbing than I expected. I assumed I would use my own but the kit straps With locking adjusters are nicer. I did not use the Included front and rear rope straps as I do not Trust the knots and takes too long to get it tight enough to feel secure. An additional set of ratchet straps does the trick. Overall I am super satisfied with the quality and value of these kayak holders and very glad I went with these over some of the J-style options which would have added substantially more height to my vehicle.

Click to Enlarge

Click to Enlarge

These work great! They fit well with my Brightlines Aero Rack where others did not. Super Good quality and super easy to install, I was surprised on the quality. I gave it 4 Stars because they sort of shift to the side if I put alot of pressure, however once the weight of the kayaks get on it, I don’t think it will be any problem.

Click to Enlarge

quick and easy installation. shipping was faster than quoted. pleasure doing business with.

I had the moulded downloader and needed the folding in order to fit in the garage. The top feed for the tie straps isn't as good as the moulded J-style rack, the strap came out of one, but the kayak stayed where it needed to be. It is easy to raise and lower the rack, but I am not always sure at what angle I am supposed to set them. With the moulded J-style, they are at the perfect angle for holding a kayak. I wish the clamp that goes under the bars were a better fit for the oval bars, but they do send two different size bolts and the longer ones work.

Click to Enlarge

Click to Enlarge

The Malone DownLoader is very good value for the money. The J-style cradle is nice when you have to muscle a kayak on top of a tall crossover or SUV. You can hook the edge of the cockpit onto the base of the cradle and flip the kayak up onto the metal hoop support. Carrier installation and removal is easy and doesn't require any tools. Materials are good, but not great and that's what prevents this product from getting 5 stars IMO. The foam padding is nice enough and has been durable, but the metal plate that attaches the carrier to the roof rails is plastic coated steel and the plastic cracks over time, and leads to rust on the steel plate beneath. Not a big deal, but it might compromise the plate over time. I also wish that the provided nylon straps were longer, and that the ratchet buckles were covered in rubber to protect the roof of the vehicle and the windshield when you're trying to get them around the hull of the boat. We quickly replaced these with longer aftermarket straps that have rubber covers over the buckles. Those minor points aside, the Malone DownLoader kayak carrier gets the job done easily and safely, and does so at a very affordable price point.

Click to Enlarge

Click to Enlarge

These work great and I was able to install them on the OEM rack for my truck. The only downside is that the threads for the clamp hang down a little too close to the roof for comfort.

The Rhino-Rack 2 Kayak Carrier I ordered from etrailer was easily reviewed and ordered from their website and ALL communication relative to order confirmation and extreme detail included in their tracking was nothing short of phenomenal! The items were packaged with care and arrived intact. These fit our basic Lexus crossbars and is the perfect product for carrying our two (2) kayaks. My hat goes off to the great folks at etrailer -- It doesn't get any better than this!!!

I installed these as soon as I got them and I’ve got to say, there are some extra holes for screws that are a tad misleading and the pieces that secure it to the cross bars don’t seem super secure. For reference, I do have Rhino Rack’s vortex crossbars so this should fit snug. The rubber tops were tough to get into place and I am worried they’ll snap when I go to remove my rack but Rhino Rack has yet to fail me with their products so I bet it’ll work out great!

Click to Enlarge

This is a great product. As a novice kayaker I was nervous. The assembly was easy with clear instructions. My sales professional Crystal K. was a pleasure to work with. She knew the answers to all my questions. From placing the order to the delivery I am very satisfied. I will be using etrailer again. I can't wait to get my kayaks to the water.

Click to Enlarge

Click to Enlarge

This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.

Click to Enlarge

I think the Thule Hulaport kayak racks are the best, most secure way to transport your kayaks. I had these on my Xterra and hauled two kayaks up to Cape Bretton park in Nova Scotia, Canada from Connecticut, USA no problem. We were even able to store gear in the kayaks for the trip. I’m so excited to have them for my Crosstrek. Highly recommend these!

Click to Enlarge