Best 2018 GMC Terrain Bike Racks

First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Okay, this is AMAZING. From START to FINISH ordering from you was a pure JOY! I mean, every step of the way I felt totally taken care of. My rack even arrived days ahead of time which was a fun surprise! Thank you for outstanding service! I will see what else I can have fun ordering from you. :)

Ordering the correct product was quick and easy. Site is easy to navigate and understand. We received our bike rack in less than a week. Good quality and box was undamaged. Just in time for us to take our bikes on vacation!

I’ve owned the Swagman XC hitch bike rack for a year now and couldn’t be happier with it. This rack is easy to use, sturdy, and holds the bikes firm over any terrain. I’m currently using it on my Hummer H3, only needing to get a 14” extender for the 2” hitch. Well worth the money!!!

Click to Enlarge

Click to Enlarge

Delivered early and in good condition. Assembly was easy but had problems with Allen bolts seating. Didn’t fully tighten down. Tried to back out and restart but not successful. Their holding but not snug. Don’t know if this will be an issue. Overall great product.

I was told my carrier would arrive on Wednesday and didn't expect it to be here being xmas so close. It arrived on Wednesday as promised and took it right out of the box. Was easy to assemble and very please with the quality in it. Strong steel and made well. Took it out and put it on my GMC Terrain with no problem. Winter here in Ohio so have to wait to use it in the spring. This product is exactly what I was looking for, can't wait till spring when I can use it.

The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.

Click to Enlarge

I purchased this rack a year ago and have used it on several trips. The longest was 4 hours through some unpaved terrain and the rack was great! Because it's not attached like a hitch or roof rack, expect to adjust the straps every 1-2 stops. Nothing major, the side straps seem to slide a bit during travel. The guys a etrailer are absolutely exceptional. Very fast with communication and focused on great service.

Okay, this is AMAZING. From START to FINISH ordering from you was a pure JOY! I mean, every step of the way I felt totally taken care of. My rack even arrived days ahead of time which was a fun surprise! Thank you for outstanding service! I will see what else I can have fun ordering from you. :)

This is a sturdy and safe bike rack. We've used it for long and short drives to bike paths, and love it! I have a 2016 VW Jetta with a dealer-installed tow-hitch which the rack attaches to, and we've had no issues. The rack holds the 2 bikes securely on high speed roads, as well as on lower speed off-road byways with gravel and unexpected rough terrain. The "tilting" feature comes n very handy for trunk access. I highly recommend this Curt 2 Bike Platform Rack.

I installed this rack onto a Curt trailer hitch which is mounted onto a 2017 Honda Fit. I have been using it intermittently for several months, probably about 5 times with one bike and twice with two bikes. I give some pros and cons below and then elaborate. Pros: easy to assemble, easy to mount and dismount bikes, easy to lock and unlock, how to put the rack into different positions is intuitive Cons: inconvenient to put the rack into different positions, inconvenient to mount the rack onto the hitch, rack protrudes about 15 inches from bumper when in flipped up position (seems very vulnerable to someone backing into it in a parking lot, very inelegant looking I say the repositioning is intuitive because there is really only one way you could possibly place the pins for each position. But removing and replacing two pins is much less convenient than turning a knob or a lever, like some racks do. Also many racks fold and flip in such a way as to look very unobtrusive when in non-use mode. This one looks like kind of a monstrosity. That does not really bother me but it might bother some owners. The part that does bother me is how far it protrudes from the car. I back into parking spaces whenever possible to avoid someone bumping into the rack and damaging it (which happened to a friend). My number one suggestion for Curt is related to mounting the rack onto the hitch. Make it easier to tell when the holes are lined up so that the bolt/pin will fit and thread. As it is now, if you insert the rack as far as it can go it is way too far in. Ideally, it would be exactly lined up. Failing that, maybe some kind of click or other feedback to know at least that you are in the neighborhood. It would also be great to have an attaching device that is easier to fasten and unfasten than is the bolt/pin. Tip for mounting the rack onto the hitch: I assumed that it would be awkward to hold, what is it 46 pounds?, while trying to line up the rack probe with the receiver. If you have a garage with exposed collar ties, my solution could work well for you. I looped a cargo strap over a collar tie. Then I hooked both hooks of a bungie onto that loop. The idea is that you hook one of the bike frame holders of the rack onto the bungie, suspending the rack a few inches off the garage floor. This takes most of the weight of the rack so that you can just pull up or down and forward until you line up with the receiver. Tip for mounting bikes. Don't put the little screw into the post that prevents you from completely removing the bike frame holders. Remove both holders. Position the first bike, slide the holder into place, position the second bike, slide the holder into place. I found this makes it much easier, because you avoid parts of the bike hitting the holder as you are trying to get the wheels into place. The trick is that if you are mounting only one bike, don't forget to put the second holder back on - or maybe just stick it inside the car right away.

Click to Enlarge

Click to Enlarge

Works well for transporting two 29" wheeled mountain bikes. However, after one year it's starting to rust in several areas (see attached photos), and the front wheel arms are becoming increasingly difficult to raise and lower. Finally the locking cable is extremely rusty as you can see in the attached photo. I'm not sure how durable this rack will be long term.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

We have had this bike rack for one year and use it every week-end. My wife has a Trek e-bike (52 lbs) and I have a regular Trek hybrid (23 lbs). The rack is very sturdy and I have no issues driving at highway speeds, there is no movement of the bikes. Very easy to load and unload.

Click to Enlarge

I purchased this bike rack a year ago and I use it A LOT. I had to buy and install a stabilizer because without it, the unit would sway back and forth even without a bike on it (very noisy). This makes removal more cumbersome but since I keep the hitch on year round it doesn't matter to me. The tilting function is fabulous allowing easy use of my RAV4 hatchback. I can even tilt it down with a bike on it. I got the 2 bike hitch. Plenty of room for two bikes to fit without rubbing. Lastly, the hitch has a sizable through-hole on the bottom to thread a good sized cable so I can lock my bike up. Sturdy. I highly recommend.

The unit ‘s simplicity is a real plus. It takes less than 3 minutes to put the rack on the vehicle. It is well built and very durable and has a nice feature that allows you to open the rear hatch for SUV owners without removing the rack.

Draw-tite Sportframe Trailer Hitch Receiver Class I - 1-1/4 Swagman Trailhead 3 Bike Rack - Tilting The Draw-tite Sportframe class 1 trailer hitch and Swagman Trailhead 3 bike rack were ordered for a 2017 Honda Fit. The online order and shipping went just as expected. The trailer hitch and bike rack are very heavy duty. I recommend watching the trailer hitch install video before installing, whereas the video is very helpful. The bike rack has triangles that you can rotate to find the best fit for your bicycle's frame. The rubber straps are thick and secure the bicycles when you pull them tight. This bike rack will stay on the vehicle for 6 months each year. The tilt feature and folding arm feature are must haves for a smaller hatchback. I am pleased with this purchase, it appears to be good quality and good value.

Click to Enlarge

My previous bike rack was a hitch mounted Yakima. It was sturdy but not well suited for my low Subaru Impreza. It stuck out too far and hung too low so that I had to inch my way down the driveway or over speed bumps for fear of it bottoming out. A roof rack or a rear window mounted rack was not suitable since I wanted to be able to also carry two kayaks. First, I tried to modify my rack by shortening the part that sticks out of the hitch. I tried to saw off about 6 inches so it wouldn't stick out so far but the steel was much too hard. I ended up ruining several metal-cutting blades on my power saw before I gave up. I looked for other rack options. There weren't many out there. But eventually, I found something that met my needs. I purchased the "Swagman Trailhead 3 Bike Fold Down Bicycle Hitch Rack" in 2013 from eTrailer.com. The part that enters the hitch curves up to increase clearance from the ground. It is sturdy and sticks out far enough so I can still open my trunk hatch without having to lower the main vertical bar on the hitch (though I could if I wanted to). It isn't often I am really excited about a piece of gear but this hitch rack has made me worry-free when I transport my bicycle(s) via car. The only thing I don't like is that it is advertised as being a 3 bike carrier but it only fits 2 hybrid bikes. Maybe it will fit 3 skinny racing bikes but for the average rider, don't expect to fit on more than 2. But my experience is that is the case for all bicycle racks.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

At the age of 70, I needed a “friendlier” mounting and bike access rack. A platform rack seemed to be the solution. I had one caveat. My Subaru Forester had a 1and 1/4” receiver (with a non-standard 3/4” length mounting hole). My Volvo had a tuck away 2” receiver. After some research I gravitated toward Thule only to find out they had no solution for my above conundrum. In fact their customer service offered no interest in solving my problem which others also must have had. More research…enter Saris! An American made company with an innovative solution. I quickly received my SuperClamp EX-2 from ETrailer along with excellent customer service support. The ease of constructing the unit for use and the obvious structural integrity was immediately apparent. My wife couldn’t believe how easy it was to use and to stow away on my garage wall after use. Thank you Saris and ETrailer for a wonderful product and experience. I guess American made is still alive and well. I highly recommend this product and the associated companies.

Purchased this bike rack last year and am very pleased with the stability of the rack. The straps and clamps secure the bike well to the rack. Some things that I learned: When attaching the rack onto your hitch, it helps to put a piece of tape on the rack (hitchtite) once you have lined up the holes. This will make it easier to find the exact location of the holes the next time that you want to use the rack. Finding the exact location allows you to smoothly hand tighten the bolt to the end of the hitch. At that point, just use a socket wrench to finish the tightening. When putting the bike on the rack, I loosely secure the clamps to the tires at first. This allows me to rotate the tires to find the right location in the wheel well for the straps to go around the spokes. I next secure the bike with the straps and then fininsh securing the clamps to the tires.