# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Meaty
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 2
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
Very cool product, change the ball without a wrench! High quality materials and construction! Super service from etrailer!!
It's nice to have the quick-change ball available at all times. The case keeps everything in one place and fits nicely in the well.
# 3
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Great product and works well.
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
# 4
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Meaty
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
# 5
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Very cool product, change the ball without a wrench! High quality materials and construction! Super service from etrailer!!
It's nice to have the quick-change ball available at all times. The case keeps everything in one place and fits nicely in the well.
# 6
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 7
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
I ordered everything for my Acura RDX to put a hitch on as well as the drawbar. Everything fit like a glove.
Haven't had a chance to use it yet, but install was easy and materials all seem well made.
# 8
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 9
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
Great product and works well.
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
# 10
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Great product and works well.
I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.
# 11
Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount - 7" Rise to 9-1/2" Drop - 5,000 lbs
We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.
Rusted within 30 days. The manufacturer refused to warranty the product. I have continued to use it, but it has required some serious rust mitigation and is a flawed product.
# 12
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
# 13
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Nice combination to go with my front hitch for the F150.
dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento
# 14
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise - 4" Drop - Extra-Long - 6,000 lbs
Meaty
I needed an extended ball mount for my new Jeep in order for my utility trailer tongue to clear the rear mounted spare tire. Item is as described on the web site and was received earlier than expected. etrailer has great customer service and is my number one go to place for towing and trailer supplies.
# 15
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 16
Curt Fusion Ball Mount for 2" Hitches - 1-7/8" Ball - 2" Rise - 5,000 lbs
Exactly what i ordered and it came fairly quickly! Im very happy worh everything!
# 17
etrailer Ball Mount Kit for 2" Hitches - 2-3/4" Rise or 4" Drop - 7,500 lbs
Very cool product, change the ball without a wrench! High quality materials and construction! Super service from etrailer!!
It's nice to have the quick-change ball available at all times. The case keeps everything in one place and fits nicely in the well.
# 18
Draw-Tite Ball Mount for 2-1/2" Hitches - 1-1/2" Rise, 3" Drop - 10" Long - 18K
Well the first one was lost in shipping so I had to buy something local but I will definitely be using this one instead. It is MUCH beefier then the 14K one I picked up locally.
I have a truck with a class 5 hitch. Using the 2" to 2 1/2" adapter had a lot of play in it and this ball mount removed that play. The truck and me won't bounce around so much. Thanks for the great deal and fast shipping. Will be shopping with you again. Thanks again.
# 19
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
Very cool product, change the ball without a wrench! High quality materials and construction! Super service from etrailer!!
It's nice to have the quick-change ball available at all times. The case keeps everything in one place and fits nicely in the well.
# 20
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Great product and works well.
Works perfectly. Fast shipping. Very Satisfied.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."