Best 2013 Ram 3500 Camper Jacks

Haven't installed it yet.

The system is not what was advertised, it's better, at least for me. Everything arrived on a pallet in excellent condition, except for the advertised remote. I contacted etrailer and they put a replacement on order which I received a few days later. In the meantime, I tried to place the controller in the mode to sync the remote and see if the remote I had with my RV would sync, but I could not get the controller in that mode to accept a remote. Upon reading the controller label, I noticed it said BT and had a passcode on the side of it, so I downloaded the app and it connected to my phone. It seems the LCI Linc remote is obsolete for my Ground Control 3.0 and it is now using the phone app. Everything seems to work as expected; I'm excited to try everything out this weekend on our first outing. I was able to push a fiberglass push stick from the front basement to where the rear jacks are located without dropping the underbelly and pull all the required cables to the rear of the camper and utilize existing frame holes to bring the connectors out to the rear jacks. I think this will be a nice upgrade to our fifth wheel after our factory landing gear failed.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

So far so good, right out of the box it worked the only thing Is it goes very slow but that could be due to the cold weather 22 degrees outside I checked my battery @ 12.8 volts so it’s not that. I guess I will see once hot temps get here. It can’t be the weight of my travel trailer tongue weight is 450 lbs so it’s not even a 1/4 of the weight it can handle. Rated at 3500 lbs my old hand crank jack was rated at 2000 lbs so I will see I hope it goes a little faster. Time is money.

Ordered this Jack for my Travel Trailer to replace my manual one. Shipping was super fast ordered on Thursday got it on Monday. Installation was quick and easy took less then 30 min to take the old one out and put this one in. Works great so far.

Ordered this product to provide more stability in our 5th wheel, as it was quite wobbly... Packaging was damaged, both exterior and interior box. The retaining pin for one of the feet was missing and the the exterior box had been taped up where the damage was. Won't be until after the third foot is attached that I will know if it provides stability to the front of trailer.

My order arrived soaking wet box torn up and mashed. Light switch in side fox was destroyed by king pin stand. Not sure why anyone would place a fragile items in with heavy steel components.

Haven't installed it yet.

Let me say this to start, this system is AWESOME!! If you do not have a leveling system on your camper, this one works very , very well. I will say, the install and the learning curve takes time and is not too hard, but it's not super easy either. Once I got the system in place, and understood how to use it, the rest was a piece of cake. Take your time on the install and get help. The parts are robust and heavy, so two people make it much easier. Have sharp drill bits to drill the attachment holes. Wiring is super simple, but take your time and make sure you get all the connections good and tight and secured well with zip ties. The system requires a good strong battery, so make sure your battery is in great shape and you will not have any issues. Get the Lippert app also, it is very helpful. I love it now, when I pull my 2006 Keystone Raptor 5th wheel toy hauler into a campsite, I hit a couple buttons and the longest it has taken to level my unit is 2 minutes and 30 seconds. I love it! It puts the camper at the same level every single time, which is awesome. No guessing, no driving up and down on blocks, just push a button and walk away until the camper is perfect. Would I do this over again you ask? Absolutely. Awesome system!

Click to Enlarge

Click to Enlarge

Made my 5th wheel toy hauler rock solid.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

These are great and made our small 5th wheel rock solid, I mean night and day compared to just landing gear and rear stabilizers. I did have to do some minor fabrication for both the front and the rear. The front was due to the spare tire being mounted under the front of our rig. Also the instructions really suck as do most Lippert components instructions. Way too many words that don't really seem to be coherent, seems like just a few words and some good quality pictures would be more helpful.

Click to Enlarge

Click to Enlarge

Click to Enlarge

This was a replacement jack for a flat bed trailer. Installed it and it was just like the old one. Very happy with the jack, I recommend it highly.

Heavy duty, well-built jack. I decided to upgrade my trailer jack for poor performance and after searching the net I came across a video from etrailer describing the features of the Bulldog Square Jack # BD182804. It has every feature you need and some. With the upgrade, I must mention there was welding involved. I first confirmed there was structural support where the jack was to be mounted. I disassembled the jack per the video, located and welded the housing in place, reassembled the jack and lubed with the same grease I use for my trailer axles. It was that easy.

Great directions for manual assembly, quality metal and parts. Solid and exactly the heavy duty I was looking for to use with my slide in truck camper.

Click to Enlarge

Click to Enlarge

Click to Enlarge

The Brophy jacks were strong, stable, easy to position, and easy to lift and lower my camper. it is a much better method than having four jacks to maneuver. And it cut down my time to 30 minutes total to load my camper instead of an hour and a half! I have to start from my garage and winch my camper down on a cart to the street face because of the incline driveway is so dramatic and my camper won’t fit in my garage if it is attached to the truck. I couldn’t be more happy they were great and now I have my truck loaded with my very modern camper and I’m enjoying quite the holiday! I’m using the 3 ton 67 inch trophy jacks and I’m lifting an 800 pound gross camper. The stability is outstanding.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Definitely a heavier duty version of our campers stock stabilizers. They bolted right up to the brackets and glad we have new stabilizers. I hope the paint lasts on these as that seems to be an issue with the other, cheaper stabilizers. Time will tell.

if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Delivered on time, easy to install and working great. Could have been 5 stars if customer service had known that this model was the replacement to my original rather than telling me to measure the mounting holes. Called Lippert my self to verify after messing around with the measurement.

I bought the stabilizer shipped out very quick, received in two days. I am not able to install yet on trip for a week will input more info after install.

Easy to order. The landing gear was an exact replacement. It installed without issues. I will definitely continue to buy from etrailer. Thanks

The product itself was great. It fit right in to the brackets from our old landing gear. We were able to use our existing motor as a cross fit with this gear. The gear box was even better than Lipperts as it was not plastic. The only issue we had with this was shipping. We ordered the part same day as our water pump because we were told it was in stock. Low and behold they changed ship date numerous times, with the excuse it was not easy to pick. Anyhow, two weeks later we finally got the part we ordered.

Click to Enlarge

Click to Enlarge

Delivered on time, and time will tell how they operate compared to the 4500.

You guys went above and beyond my expectations with my shipment . After having a hiccup in shipping you shipped out the next box super quick and I was super happy with your service. Thanks etrailer

etrailer is my go-to site for useful, expert opinions, reviews, install videos and more for every product I need for my truck and trailers! These guys cut through all of the sales speak clutter and get to the facts that really help me make decisions. I'm thrilled about this new auto leveling system and can't wait to get it installed on my toy hauler!

We love our one touch jack system. We used in on a 3 month camping trip out west setting up probably 40 plus times and we continue to use our camper and the jacks work great!

Easy to order. The landing gear was an exact replacement. It installed without issues. I will definitely continue to buy from etrailer. Thanks

Perfect replacement, works great, excellent shipping time and service. Just wish I had got the electric motor that goes with the legs.

Click to Enlarge

Very solid product. I needed the extension legs for my particular 5th wheel not a problem to install them. Etrailer costermer service was very helpful to guide me to the right products I needed.. I would definitely recommend this product!

Tripod is well built and should a good job, just as I expected. etrailer's web site was easy to navigate and shipping was fast and as promised. My only comment is the manufactures box appeared to be durable, but when it arrived it had a large hole in the bottom, luckily all pieces were still in the box and nothing was damaged.

I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."

Click to Enlarge

Awesome product. My back thanks you. Very easy to install. Only thing I would change is the speed of the motor. A bit slow but still better than hand cranking.

Click to Enlarge

Click to Enlarge

Didn’t last 3 months the end came off and screw mess up where the jack don’t work anymore

Worked beautifully for a Replacement for our customer

Took the sway out 95%. Excellent customer service! Quality product.

Click to Enlarge

Click to Enlarge

We have motorized stabilizer jacks on our 33'camper. The JT Strongarm jacks did not provide the extra stability we were hoping for. There is still a lot of motion when anyone in the camper moves.

As always a big help in getting what I need, and wanted. Good tec help, fast service. Already installed.

Click to Enlarge

The bolt pattern matched my trailer so it was very easy. No skill needed. I soldered a connection on and hooked it directly into the battery. I had to drill a hole for my foot extension. So far so good. 23 foot travel trailer.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I finished the assembly and install of the power twin II stabilizer and have included pictures of the install. This is a good quality unit and I am very happy with how it works. Bob

Click to Enlarge

Click to Enlarge

Click to Enlarge

Wish they would have built the motor and controls into the rear half of the jack leg for tailgate clearance (took off one star), but honestly on our trailer it would not have made any difference since the mounting point was so close to the trailer tongue. Otherwise the jack works great so far. Haven't come close to testing it's 3500 lb capacity and probably never will. It runs slow, but that's a function of the gear reduction. Seems to have been paint very well, don't expect chips or rust. Like that it has the back up hand crank. Great value!

So far so good, right out of the box it worked the only thing Is it goes very slow but that could be due to the cold weather 22 degrees outside I checked my battery @ 12.8 volts so it’s not that. I guess I will see once hot temps get here. It can’t be the weight of my travel trailer tongue weight is 450 lbs so it’s not even a 1/4 of the weight it can handle. Rated at 3500 lbs my old hand crank jack was rated at 2000 lbs so I will see I hope it goes a little faster. Time is money.