Most Popular Tail Light Mount for 2013 Honda Pilot

Yet another good product/service provided by etrailer.com. Even if they are a bit more on their price I generally use etrailer.com because of their excellent service. Top notch company. This Wiring Kit went in just as advertised. Of course it took me longer than I expected but that is normal for me. I work slow but my result is always a first class install! :-)

Installation was straightforward and fairly simple. The hardest part was finding a routing for the wire to stay away from moving parts. That will be different for each vehicle.

In ordering the parts I got a little confused as to exactly which kit I needed. My motorhome has combined brake/turn signal lights & the car ('03 Subaru Outback) has separate brake/turn/parking lights. Thought I needed the 6 diode kit (which I ordered) until I had all the parts here & read through the instructions for the umpteenth time (BEFORE cutting anything) & then realized what they were doing. Turns out all I needed was the 4 diode kit. Sounds like there won't be any problems returning the unneeded parts since they were never installed. Great service there! Took a lot apart in the back of the car because of the lack of space behind the tail light assemblies, but it all comes apart pretty easily. Also allowed me to route the wiring along side the stock harness. Have a bunch of 1/2" split loom here & used it. Thought I would have lots of wire left over, but I actually had to splice 2 cut offs to make a jumper long enough to get from 1 side of the car to the other. Glad the car wasn't any longer & I didn't have to make up 2 jumpers as with some of the kits! Hardest part was finding a hole in the firewall & getting the harness routed under the dash so as to not tangle with the pedals, etc. I just don't flex like I used to. Everything works fine although it was NOT a "5 minute job".

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The diodes and wiring are good and worked well. But the 118158 converter produced a 3.5 volt drop such that the brake lights were as dim as the tail lights. And when a turn signal was triggered the brake lights dimmed even further. I ended up stringing a separate brake wire through the car and re-wiring my truck with a 5-wire connector.

Click to Enlarge

Very complete kit. My only problem mounting it in a 2014 Chevy Spark is the limited space for the diodes. After much trial and fitting I found a suitable location. See photo.

Click to Enlarge

Click to Enlarge

Finished wiring and first effort to plug in red flex coil to the Jeep and the outside protection cover broke apart; very disappointing. Trying to contact Etrailer for replacement.

Click to Enlarge

Click to Enlarge

I was looking for something to add to my 2014 Equinox for tail/brake/t-signal lighting for towing behind my motorhome. This system worked perfectly , and couldn't have been easier to install. The hardest part was running the wiring from front to rear ( through frame rails and what-not ). Tail-lite hook-up was a breeze. There was plenty of wire to do the job also. Now the vehicle lites work as a trailer and does not interfere with the normal vehicle lite operation.

Click to Enlarge

installed your isolating diode wiring harness 38955 also the blue ox base plate bx1126 . install was very easy with video on your site.was installed on my 2007 wangler to be towed with holiday rambler motor home.

Click to Enlarge

Click to Enlarge

this is the only company I will buy from

It does what it says on the tin. Easily lit up my XJ so I could tow it. Only regret is that by making the connections at the rear, you don’t get the front market lights on the toad. I should have connected the running lights diode in the harness under the dash so all the marker lights come on at night.

I needed to wire our ‘17 Chevrolet Sonic for towing behind our Motorhome. My local shop wanted over $xxx to install such wiring. Online I found the Blue Ox wiring kit and decided to do it myself. The kit and instructions were very complete and informative and it took me about three hours to complete the installation. The time consuming part was removing and reinstalling trim and panels to hide the wiring inside the car. The thing I like most about this kit is it’s independent of the cars wiring system and I’m very happy with it.

I put this base plate on with the assistance of my wife very easy to install. Do recommend the video to install

Click to Enlarge

Worked perfect for setting my 2001 Jeep Wrangler up for flat towing behind my Motorhome. The instructions were clearly written, the diode was clearly marked and all the connectors were there to make this wiring job simple.

Haven't installed yet but service was excellent

Bought this light kit to install in the un-used bottom position in or 2005 Honda CR-V. No need to tap into vehicle's wiring harness. Easy to install, works great! Highly recommend.

Click to Enlarge

Click to Enlarge

This bulb kit is just what I needed to add trailer lights to my 'toad' vehicle. The sockets felt like quality items, it was simple to install. I had my own wire, I think it turned out great.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The install on my Ford Maverick is clean and functional, so this is more of a customer service review... excellent customer service! During the 4-day towing set-up install, the forecast was for freezing temps and my rig was not winterized. I called in mid panic and the motorhome was moved indoors. A few months after using the tow set-up, a minor problem developed. I called and the CSR apologized and said, I can see how that might be frustrating, and a replacement cable (slightly longer) was sent free of charge.

Click to Enlarge

The installation ins ructions and video were very helpful. The wiring kit worked perfectly.

This place is the best! Placed my order- easy peasy-delivered on time- Watched install video- again made it so easy and saved $1000 installation fee!!! Thanks for being a great company and special thanks to Carol C my order specialist !!!

I installed this myself along with a tow bar from another company at the same time, in about 4 hours. installation was straightforward and worked perfectly. saved about $800 in total labor.

Installed in my 2024 Chevy Trax. I ran the wire harness up through the front fender, and along the DS rocker panel. No drilling into body required. However, I purchased extra loom to better protect exposed wires next to body. Additionally, I purchased extra wire to support the DS to PS taillight connections. Finally, be advised the plastic taillight assemply is "double hulled," so once you bore through the exterior of the assembly, you will need to drill again, into the lense. On this point, and to ensure a good fit of the bulb socket, a Dremel tool was used to grind down the plastic surface, to ensure a good flat and tight fit. Finally, I used the first cut-out to fashion a cap and to seal the light socket installation. See pic.

Click to Enlarge

I am very happy with this kit. It gives you everything you need to setup an independent brake light system for you toad and therefore bypassing the vehicles internal wiring and computers. I went with this setup as I did not want to complicate my wiring or damage the internal systems of the toad. IT takes sometime to install, but once done hooking up and running the system is simple as plugging in your 7way connector. Combine this with a onboard braking system, and you have the perfect system to pull your two vehicle behind your RV.

The labels for the Right Taillight Running Light splice were labeled Backwards, to module and to vehicle were reversed which wasted 30 minutes of time. Beware! etrailer may want to get this right with the vendor or risk a bunch of needless returns.

I have bought off of you before everything was great this is the first time that I received something that was not what it was supposed to be or was used before the papers on the installation were all wrinkled and dirty and had writing on the ends of the wire were all cut and the connectors were not on I called your company and they made it right and gave me back my money except for my shipping and they told me just to keep it it's no good to me but thank you and I am still buying off of you

Called my local trailer and flat tow company in my area and they quoted me $179.00 for the harness alone. I also got a quote for the install which was $350.00 and the total of $529.00. Called Etrailer and purchased the Hopkins harness that was on sale and paid total of less than $82.00. It took me around 2 hours to install with wire loom protection. Etrailer has always had excellent customer service. Big thanks to Brandon for all his help.

Relatively easy to install, worst part was routing the wiring to the front of the jeep. The rest was plug and play. I also replaced the flat four way plug with a six pin round.

etrailer was extremely helpful in getting me parts to flat tow our 2023 Jeep Wagoneer. More specifically, Noah took the time to research the required parts, offer technical guidance, and follow up to ensure I was taken care of. Top notch service which was much appreciated.

Needed new wiring and diodes for my 2023 Jeep Rubicon. ETrailer makes it so easy to set up all the wiring for flat towing.

Great wiring kit. Everything fit and worked perfectly on my 2013 F-150

Big job, completed in 4 hours by myself. Not bad for a person 81 years old. Once again great instructions.

This kit did the job very well. I could have bought each part separately and saved some money, but I went with the comfort knowing all these parts will work together to accomplish the job. I couldn't figure what LED bulb to use for both brake and turn signal. I routed the wire along the truck wiring harness for half the way to the front, then slipped it into the frame channel for the rest of the way. I used a Curt heavy, round 4 pin plug at the front grill. It was a bit of work and took many hours but came out clean!

I installed this on our 2019 Equinox towed. Love the convenience of just plugging in the towed vehicle. The most difficult part was deciding on what part of the light housing to drill the hole for the light socket.