# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
What I ordered quick shipping. Easy install
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 2
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
Great quality and very reasonably priced.
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
# 3
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
What I ordered quick shipping. Easy install
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
# 4
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
This drawbar was clearly used. See the picture. I asked etrailer about it and sent this picture but the person that replied, Noah, thought it must have been bumped around in shipping. If shipping caused this much damage, it's a poor quality product. If it was, in fact, used, then etrailer lied to me. Either way...not good.
# 5
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I bought both the hitch and ball receiver. The ball receiver was well package and arrived unscathed...unfortunately the hitch arrived damaged or poorly painted. As the attached photo show a bit of sliver metal is visible and I'm concerned that rust will attack and weaken the structure. This uneven and rough area is located on both sides and at both ends. I not sure if it is all damage because of the roughness of the blemish. The area pictured is worst of the four damages. The shipping carton shows damage and repair to the box tear. The tear was repaired with clear tape and staples. The metal staples could have caused some damage exposing the bear metal. I just happen to have some black spray-can paint and will cover the bear metal before installing later the morning. Thank you for this product review opportunity.
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
# 6
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
I bought both the hitch and ball receiver. The ball receiver was well package and arrived unscathed...unfortunately the hitch arrived damaged or poorly painted. As the attached photo show a bit of sliver metal is visible and I'm concerned that rust will attack and weaken the structure. This uneven and rough area is located on both sides and at both ends. I not sure if it is all damage because of the roughness of the blemish. The area pictured is worst of the four damages. The shipping carton shows damage and repair to the box tear. The tear was repaired with clear tape and staples. The metal staples could have caused some damage exposing the bear metal. I just happen to have some black spray-can paint and will cover the bear metal before installing later the morning. Thank you for this product review opportunity.
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
# 7
Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 7-1/2" Drop/Rise - 16K
All in all a good set up. A lot more play in the receiver than I expected. Fair amount of rattling around without a trailer attached. In all fairness I do live in a state with poor roads.
Has done what it is supposed to do. I have used the hitch to tow two boats over the last two years using both ball sizes. The only issue is the appearance. Saltwater creates rust and break down of the coating on the hitch. Was never dunked in salt has been effected being near saltwater. Hitch was washed with freshwater after each use in salt. I probably wouldn’t buy again. I have seen some other hitches that can do similar adjustments that do better near saltwater environments.
# 8
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 3-1/8" Rise - 3,500 lbs
Service from eTrailer was great, they even wrote to ensure I got the order correct when I ordered a different size hitch cover than the drawbar that I ordered. Picture attached of the somewhat unique application for the Euro style setup I’m using – I’m dragging my race tires to racing events with my 750HP Cobra!
After speaking with an etrailer phone rep, I did some measuring and opted for this Curt Euro-style drawbar. It looks good on my 2018 Kia Niro, and gets the ball height up 2" and back 3" from where my old ball mount was (much too close to license plate and trailer a bit low in front). For my car, it's the perfect match with the Curt trailer hitch.
# 9
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Drop - 7,500 lbs
Purchased for a 2006 Jeep liberty. the only issue I have is that it connects right below the spare tire, making trailer attachment more difficult that it should be. If I had gotten a slightly longer hitch, wouldn't have been an issue. It's not a deal breaker, and the hitch itself has works perfectly.
I haul a 5.5x10 open trailer w/ a 900 lb. ZTR, a push mower, and a handful of other tools 3 days a week. It is what it is. It does the job, no problem. A little finish wear and rust on the ball, but nothing major. I LIVE ON A DIRT ROAD, which is probably responsible for the wear.
# 10
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
I bought both the hitch and ball receiver. The ball receiver was well package and arrived unscathed...unfortunately the hitch arrived damaged or poorly painted. As the attached photo show a bit of sliver metal is visible and I'm concerned that rust will attack and weaken the structure. This uneven and rough area is located on both sides and at both ends. I not sure if it is all damage because of the roughness of the blemish. The area pictured is worst of the four damages. The shipping carton shows damage and repair to the box tear. The tear was repaired with clear tape and staples. The metal staples could have caused some damage exposing the bear metal. I just happen to have some black spray-can paint and will cover the bear metal before installing later the morning. Thank you for this product review opportunity.
Works perfectly. Fast shipping. Very Satisfied.
# 11
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
What I ordered quick shipping. Easy install
I had previously purchased the etrailer hitch for my 2021 Ford Transit 150. It was a little short in length and the bumper prevented my current ball mount from working. As always, etrailer had the perfect solution. The Draw-Tite is well made and will now remain permanently with the van to be handy whenever the need arises.
# 12
Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
I bought both the hitch and ball receiver. The ball receiver was well package and arrived unscathed...unfortunately the hitch arrived damaged or poorly painted. As the attached photo show a bit of sliver metal is visible and I'm concerned that rust will attack and weaken the structure. This uneven and rough area is located on both sides and at both ends. I not sure if it is all damage because of the roughness of the blemish. The area pictured is worst of the four damages. The shipping carton shows damage and repair to the box tear. The tear was repaired with clear tape and staples. The metal staples could have caused some damage exposing the bear metal. I just happen to have some black spray-can paint and will cover the bear metal before installing later the morning. Thank you for this product review opportunity.
The team at etrailer relayed helped find the right solution. Using this ball mount fixed the height issue I had with my SUV not lining up with the trailer. Very grateful for their help.
# 13
Curt Class II Drawbar - 3-1/8" Rise - 9-1/2" Long - 3,500 lbs
Fits my Curt hitch as described (also purchased from eTrailer), but if pushed in too far it gets stuck in the receiver tube. Had to use a wheel puller to get it back out! Just need to push it in an inch or so to the pin holes line up not problem. My only complaint about ETrailer is that they use huge staples to close their shipping boxes. The staples are tough to pull out (get out your screw driver and pliers if you don't have an industrial strength commercial staple puller). My cardboard recycler does not want these dangerous looking staples left in the box, so I need to pull every one of them out!
Very fast delivery, Very low price for this sturdy drawbar... fits my Rav 4 Class II hitch perfectly.
What our customers are saying:
"The phone operator was very helpful and made my purchase easy. I will keep this website handy."