# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
I recently purchased a class III Curt hitch, mount, ball, wiring harness and hitch pin for my 2011 Toyota Rav 4. The installation was as described, straight forward and easy. The instructions were easy read and matched the vehicle I have. Everything fit together exactly with no modification needed. Shipping was directly to my door. The unit was undamaged and everything was shipped all in the same box. I have used my hitch several times, and although I an new to towing, I look forward to years of use. I did have to make a quiet clamp for the banging mount with an empty trainer, but from what I understand, this is common to all hitched.
Great heavy duty product.
# 2
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Bought this for the hitch on my 2011 RAV4. Quality pieces at a very good price.
this is a great set of hitches. have used the 1 7/8 hitch for the most part but enjoy having the 2" just in case. I also like the varying distances that they can be raised or elevated for a variety of needs. I am very satisfied. Thank you James J.
# 3
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I installed two Curt hitches last year. One was for a 2006 Honda CR-V and the other was for a 2011 Toyota RAV4. Both were used to tow small U-Haul trailers across the state and both performed well. They were easy to install. The only downside I have is that the ball mount rattles around in the receiver a bit more than previous hitches I have had. All in all, though, I am pleased with the product.
Right on Time !!!!!! Great product.
# 4
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
Well made product. Corrosion free and nick free after one year of use. I am very satisfied overall with Curt products.
It's a receiver hitch! It's well built, the welds are clean and it fits the trailer hitch. Not much else to say!
# 5
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Worked as expected
Hitch installation went well after viewing the installation video. The wiring harness video was not completely accurate but provided more than enough visual information to perform the wiring install in a reasonable time. Overall, very happy with product at this time due to easy install due to seller videos. Haven;'t used it yet other than to take a test drive, so, sorry no videos, Etrailer provides a good product with excellent product support. Shipping was very fast and of course the price was right. I would definitely use them again.
# 6
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
I recently purchased a class III Curt hitch, mount, ball, wiring harness and hitch pin for my 2011 Toyota Rav 4. The installation was as described, straight forward and easy. The instructions were easy read and matched the vehicle I have. Everything fit together exactly with no modification needed. Shipping was directly to my door. The unit was undamaged and everything was shipped all in the same box. I have used my hitch several times, and although I an new to towing, I look forward to years of use. I did have to make a quiet clamp for the banging mount with an empty trainer, but from what I understand, this is common to all hitched.
Great heavy duty product.
# 7
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
I installed two Curt hitches last year. One was for a 2006 Honda CR-V and the other was for a 2011 Toyota RAV4. Both were used to tow small U-Haul trailers across the state and both performed well. They were easy to install. The only downside I have is that the ball mount rattles around in the receiver a bit more than previous hitches I have had. All in all, though, I am pleased with the product.
Right on Time !!!!!! Great product.
# 8
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 9
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 10
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
Well made product. Corrosion free and nick free after one year of use. I am very satisfied overall with Curt products.
# 11
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
Well made product. Corrosion free and nick free after one year of use. I am very satisfied overall with Curt products.
The Curt Class II Drawbar with a 5" rise very nicely solved my problem when hooking up my two trailers to my Rave 4. The trailer jack was as low as it could go when it rested on the ball in my of setup. Now I have plenty of jack room to hook up and unhook. Thanks for your excellent product and service. Ralph E.
# 12
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 13
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I installed two Curt hitches last year. One was for a 2006 Honda CR-V and the other was for a 2011 Toyota RAV4. Both were used to tow small U-Haul trailers across the state and both performed well. They were easy to install. The only downside I have is that the ball mount rattles around in the receiver a bit more than previous hitches I have had. All in all, though, I am pleased with the product.
Right on Time !!!!!! Great product.
# 14
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
Well made product. Corrosion free and nick free after one year of use. I am very satisfied overall with Curt products.
The 5 inch rise on this hitch ball mount was perfect for my 07 Toyota Rav4. The rear door opens to the side on this year Rav4 and it has plenty of clearance. I tow a 16 ft aluminium boat and this 5 inch rise ball mount works perfectly on the Rav.
# 15
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
Bought this for the hitch on my 2011 RAV4. Quality pieces at a very good price.
# 16
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Right on Time !!!!!! Great product.
I installed two Curt hitches last year. One was for a 2006 Honda CR-V and the other was for a 2011 Toyota RAV4. Both were used to tow small U-Haul trailers across the state and both performed well. They were easy to install. The only downside I have is that the ball mount rattles around in the receiver a bit more than previous hitches I have had. All in all, though, I am pleased with the product.
# 17
etrailer Ball Mount Kit - 3/4" Rise or 2" Drop - 7,500 lbs
Bought this for the hitch on my 2011 RAV4. Quality pieces at a very good price.
Great deal for what you get.
# 18
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
I installed two Curt hitches last year. One was for a 2006 Honda CR-V and the other was for a 2011 Toyota RAV4. Both were used to tow small U-Haul trailers across the state and both performed well. They were easy to install. The only downside I have is that the ball mount rattles around in the receiver a bit more than previous hitches I have had. All in all, though, I am pleased with the product.
Right on Time !!!!!! Great product.
# 19
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Well made product. Corrosion free and nick free after one year of use. I am very satisfied overall with Curt products.
The 5 inch rise on this hitch ball mount was perfect for my 07 Toyota Rav4. The rear door opens to the side on this year Rav4 and it has plenty of clearance. I tow a 16 ft aluminium boat and this 5 inch rise ball mount works perfectly on the Rav.
# 20
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
I installed two Curt hitches last year. One was for a 2006 Honda CR-V and the other was for a 2011 Toyota RAV4. Both were used to tow small U-Haul trailers across the state and both performed well. They were easy to install. The only downside I have is that the ball mount rattles around in the receiver a bit more than previous hitches I have had. All in all, though, I am pleased with the product.
Right on Time !!!!!! Great product.
What our customers are saying:
"Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair."