# 1
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
It works great! Easy, quick, you know. One needs to screw in the hitch bolt, for some reason, before latching it. Other than that, it makes going bike riding way easier.
# 2
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 3
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I used 2 inch square tubing cut the length of the tie down support bracket in my 2007 Honda Ridgeline and secured with a stainless bolt and wing nut, use a large enough washer to cover the diameter of the supply hole in the Honda Ridgeline bracket on the truck. A couple of notes: Be sure to use something as a cushioning gasket to insure a snug fit and to protect your truck lining. I used rubber or foam exercise mat cut to the same as the aluminum square tubing. Use a washer that a combination of hard plastic and metal to avoid the corrosive effects of dissimilar metals in contact with each other. last: My 26" full suspension bike fits, but I have swing it to one side slightly before i close the tailgate and lift the bike up and slide it down....It's a very snug fit but the suspension adds pressure to the tailgate and its works out very well. Or you could just use a tailgate extender.
Referring to special mounting instructions if you have a bed liner: (line #3). I do not have a bed liner, but I do have a molded plastic cap on my bed rails ('04 Ford F350). The first install over the plastic cap the locking pin or pin as called out in line #3 was nowhere near making contact with the metal lip of the metal bed under the plastic. What I did next on the second and final install was remove/cut away the plastic on the inside of the bed rail to allow the vertical portion of the "L" mounting bracket (Fig 4) to contact the metal bed. The locking pin is now at a position almost where it would protrude under the metal bed lip if I would remove the rest of the plastic under the horizontal portion of the "L" mounting bracket, I did not do that. After cutting a notch in the metal rail to accept the pin, the pin barely flushes out to secure the rack. A 1/4" longer pin would take care of this problem. One other thing that was not addressed in the install instructions was if you have a full size pick-up bed you are likely to attach the passenger side fork mount (Fig 2) to the right of the extension tube locking mechanism. The extension tube is a smaller diameter, so you will have resize the fork tube clamp (Fig 1) for the smaller tube. I can't explain how to do it other than it's a Chinese puzzle.
# 4
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
Hitch pin broke before I got it. Looks like a poor design for the locking pin, they might want to consider a different design. I got a 3/8 shear pin from Home Depot to replace and it works great. Bike rack is great!
# 5
Swagman XTC4 Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
If you've done any research or read any of the other comments on either this rack, or this seller...rest assured they really are as good as everyone says! I ordered my rack on around 4pm est on a Friday afternoon and within an hour I received an email that said they have shipped my product AND upgraded to priority shipping. Can't say enough positive things about the customer service! When the rack arrived, it took me a little over half an hour to get it set up. Probably would e been faster if I were even slightly mechanically inclined (or if didn't I didn't have to borrow a socket wrench from my neighbor). We finally had an opportunity to load up the bikes and head out for a ride today. As others have said, the first time you load up your bikes, it's kind of like a puzzle to get them situated. Took about 15 minutes. This rack is awesome! Very sturdy and the bikes were very secure. Only racks I have had in the past were rooftop fork mount racks. This is so much easier! On e we got to the trail (over an hour drive) getting the bikes off was a piece of cake. Afterwards, it was time to load them back up and it was less than 5 minutes to get them all on and ready to hit the road. There were other 4-bike racks on the website, but this one had enough great reviews that I felt comfortable making the purchase. After the fact, I'm very glad I did! I can't imagine the $800 rack can be that much better than this, and I highly recommend this for anyone looking for a 4-bike platform rack. I will definitely recommend this rack and etrailer.com to everyone I know.
Loads and unloads bikes super fast, and holds them firm. Wish I would have purchased this a long time ago instead of struggling with my old frame mount rack. I actually ride more because I don't dread having to load. Adjusts to different bikes easily. Time will tell if the fittings, springs, straps hold up to weather (I leave it on car). It is fairly large and heavier than the more expensive 4 bike racks (it's mostly steel vs. composite plastic), so if you are going to take it off hitch and store it - be prepared. Only recommendation I have is to add softer foam on the frame bar for traveling on rough roads.
# 6
Inno Velo Gripper Bike Rack for Truck Beds - Clamp On
Using the Grippers for carrying 2 ebikes, weighing 55 & 75 lbs. I know this is above the rated bike weights but so far they have performed well. My short bed keeps the 75# bike pretty well locked in front to back so that may help.
I am disappointed that they don’t hold my bikes better than they do. I still have to strap them down so they don’t fall out. They are pretty expensive for what you get. I need to modify them so they will actually work. Not really what I was expecting to do, but I need to so my bikes are secured.
# 7
Softride Shuttle Pad Tailgate Pad for Full-Size Trucks - Up to 6 Bikes - 61" Wide
The fit for a 2014 Ram was spot on, no issue with the wide style tailgate top and the access flap for the tailgate handle lined up perfectly. Material is durable and easy to clean, the only thing holding it from a 5 stars is if it had the padded dividers on top to keep the bikes separated. But for the price, the fit and finish was exceptional, great value !!!
The product review/installation video helped me make my selection. I selected the full size pad for 2001 Silverado 1500. Installs easily, fits nicely, flap in pad is positioned for easy access to tailgate latch.
# 8
Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On
The Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On, is just what I was looking for to be able to build a bike rack for carrying one of my bikes on my motorcycle. It was easy to mount and it holds my bike in place while riding on bumpy dirt roads, city streets, highways and even when I hit some twisty country roads. It's really easy to load and unload my bike when I get to where I want to ride. I use a velcro strap around the quick-release and the fork arm as an added safety as well as a couple tie-downs from my bike handlebars to my motorcycle passenger pegs to help distribute the weight on my rack. If you want to build your own DIY bike rack I totally recommend the Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On.
Love this product! I built a great bike carrying system for my F-150 using two of these fork clamps. They are easy to install and extremely well made. No more tangled bikes and lots more room in the bed for other stuff! Best way to go for a nice bike rack system. Thanks, Phil T.
# 9
Swagman Upright Bike Rack for 1 Bike - Roof Rack Crossbars - Frame Mount
Planning on bringing bikes while camping. I mounted 2 of the Swagman bike racks to my new Sportrack on my pop-up camper. The bikes fit perfectly. The racks seem sturdy enough. Not heavy duty, but for my needs they should be fine. Assembly was relatively fast and easy.
We have used the Swagman Roof Rack a number of times when we have needed the additional bike carrying capacity. It took a couple attempts to get the initial spacing of the bike rack properly balanced on the van’s roof rack as recommended by the instructions. But it was easy to do and once set was very easy and quick to put on and take off. The rack works great, the bike is easy to put into place and secure. The bike and rack are very stable and quiet and haven’t required any mid-trip adjustments. We always put the cheapest bike on the roof (lol) but do use a bit of duct tape to protect the finish just Incase. We are very satisfied with the rack and consider it quite a deal for the money.
# 10
Swagman Trailhead Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches - Tilting
Quick and reliable shipping and was able to take to my mechanic to get it installed and it works perfectly with my bike rack!
This is a very solid product! I have used it for over a year now and love it! I have had up to 3 bikes on this without a problem and have traveled over 8 hours in the car one way with absolutely no issues. Many other bike racks like this one that I see on other cars look unstable this is not unstable in anyway. I did have to file some of the paint off of the rack to get it to fit in my 1 and 1/4" hitch but once that was done it has been perfect. I also bought the locking hitch bolt which is awesome too.
# 11
Curt Bike Rack for 5 Bikes - 2" Hitches - Tilting
It was obvious that we received a product that was returned by someone else when the box was overly taped shut, a support collar was broken, and most of the pieces were out of their ripped plastic bags. However, it was a great price to hold 5, 26" and/or 27" Trek bikes. I used a piece of the broken collar and went ahead and assembled the rack. Due to the weight of the 5 bikes it did not wobble that much when driving, as one of the bike tires was up against my car. I can only imagine that if we received an untampered product that this review would have been 5 stars. The picture is a little hard to see, but there are 5 Trek bikes on the rack on my 2020 Toyota Seinna.
We received a damaged box, damaged items, no instructions, the nuts and bolts are completely stripped and not inside a bag. This was obviously used, returned, not checked for quality and sent out. We are extremely upset.
# 12
Yakima HoldUp Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Works well for transporting two 29" wheeled mountain bikes. However, after one year it's starting to rust in several areas (see attached photos), and the front wheel arms are becoming increasingly difficult to raise and lower. Finally the locking cable is extremely rusty as you can see in the attached photo. I'm not sure how durable this rack will be long term.
We have had this bike rack for one year and use it every week-end. My wife has a Trek e-bike (52 lbs) and I have a regular Trek hybrid (23 lbs). The rack is very sturdy and I have no issues driving at highway speeds, there is no movement of the bikes. Very easy to load and unload.
# 13
RockyMounts MonoRail Solo Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount
could have been so much better if the front wheel backstop had been designed to fold back to allow easier loading of front tire. almost a deal breaker. the install was straight forward, all parts accounted for and decent materials for the price. but like I said with a bit of thoughtful engineering with that front backstop it would have rated a 4 that's if no surprises come up traveling a distance with the bike loaded. My bike is RadCity 5+ and weighs about 55 pounds without the battery. The weight compounds the awkward loading with that tall front backstop in the way. I doubt I would have noticed if I had been loading a light weight road bike.
I just finished installing this rack on my 2017 Subaru Outback. I've been researching platform racks for about 2 months now, and the most important things to me (other than a reasonable price) were no frame contact, ease of getting the bike on and off the rack, not too heavy for me to take it off the car, and enough clearance in the back for me to close my garage door. This rack is perfect for me. And I like that it's expandable to two bikes if I want to do that down the line. It came very well packaged. I am a single gal and not handy AT ALL, but I was able to do the installation with no problem. I did put my bike on the rack and took a short test ride, it was very stable. Very solid well made product!
# 14
Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount
This rack is perfect! eTrailer had it shipped and at my home in almost no time. I drove with it on the car today, and it was solid and secure. It's super easy to get on and off the hitch. I'm 5'1 and I was able to load the bike on with the ramp without a struggle. Thanks for the thorough video and comparison information. It made this purchase easy.
I purchased the rack and receiver hitch a year ago. Installation of the rack was made simple with the installation video that was specific to my vehicle (2020 Honda Accord). Literally took less than an hour start to finish. Only tool that I needed to buy was a torque wrench, which was about 20 bucks. It did require a very small cut in the plastic bumper that was accomplished easily with a keyhole saw. There was no drilling or other significant issues. The rack itself is awesome! My wife and I have two Lectric XP3 bikes. They weigh about 65 pounds each with battery. When we travel I revome the batteries to save a bit of weight. I have made two cross country trips (over 6000 miles) with this rack and have never had an issue. Literally every gas stop or hotel stop someone asks me about the rack and bikes. It really is that nice. My wife usually scolds me because we lose a 1/2 hour of travel time each stop to visit with complete strangers:) The rack is easy to install and remove on the receiver hitch. The lockout feature works great and gives a great deal of peace of mind. The bikes are easy to load. I don't use it, but there is a ramp that could make loading the bikes easier if a person couldn't lift the bike onto the rack. There are two arms the lock onto the frame of the bikes similar to the receiver hitch. Once locked down the bikes will not move. I would recommend ordering the longer ratchet staps if you have fat tires. I think they cost around 20 bucks but the longer straps allow for a little more flexibility in arranging bikes on the rack. I would strongly recommend this product and this company.
# 15
Yakima HoldUp Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount
Been a Yakima user for some time. Last bike rack was the Doubledown 4. Great rack but with the newer bike frames having top bars in different shapes and sizes, putting bikes on the Doubledown was a challenge. Had to go to a platform rack. Holdup was the fit. Carries 2 kids bikes without issues as well as my 29” and 27.5”. It is big and heavy but is solid and stable. Just makes it so much easier to carry 4 bikes. Just did a 500 mile round trip drive with them and no issues. Built in security cables is a nice feature. I did change out the two SKS cores to match up with the others. I’ll need to replace the stabilizer pin’s holder. It’s make out of plastic and broke right when I pulled out the pin so the cable is just hanging now. If I had to do it again, I’d buy it again. etrailer has quick shipping and great customer service.
The bike rack works extremely well and fairly easy to get two adult bikes and two kids bike. The rack can be a bit heavy if lifting all in one piece. I would recommend installing the base, then the add on. Bikes are stable and secured. The locking cable is just long enough to go throught the frame, but don't expect both tires to be locked. The only issue I had is the stablizer bold for the add on did not fit through the base rack. I called supprot and I am going to make the hole slightly larger so it will fit. Support was very knowledge and had heard of one other issue like mine so they noted my account. etrailer is great in customer support and deliver.
# 16
Hollywood Racks SR1 2-Bike Carrier - Spare Tire Mount
This HRSR1 bike carrier will not fit a 2023 Jeep Wrangler JL UNLESS you remove the stock Liddy Light and associated bracket. Upon discovering this, I was able to locate an aftermarket kit which allows for the relocation of the light to just above the rear camera. The kit was easily installed and the bike mount was installed just as easily as the directions explain. The new location of the light is partially obscured with the bikes mounted and, although not ideal, it is adequate and certainly better than total removal. I was unable to find any mention of this situation in the install instructions or reviews prior to purchase of the rack. I just wish I had been aware of this before purchase. I would have rated 5 stars for this product were it not for the slight hiccup. Kudos to etrailer. It is always a pleasure to do business with them. They are very helpful, friendly and knowledgeable.
JeepIt's sturdy even off-road, and it's simple to take on and off. I've had to use my spare tire twice since owning this rack, and although I have to remove my bike and loosen the bike rack bolts a bit, it comes off and goes back on with minimal effort, which is nice when you're on the Alaska Highway and it's snowing. I've carried my full-suspension bike on this rack for 35k miles all over the U.S. and Canada. I like how my bike fits close to the tire, where I lock it. My tailgate opens without the bike touching the side of my Jeep. Great bang for the buck.
What our customers are saying:
"The bike rack went together with ease. Everything was in the box, no missing parts. It was very stable on my first trip with it.Works well with womens bikes also. Delivery was prompt with no mishaps. Good job"