# 1
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
It's a receiver hitch! It's well built, the welds are clean and it fits the trailer hitch. Not much else to say!
Good quality and fit. Installation was straight forward and instructions were accurate.
# 2
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
I have a 2004 RAV 4 and I was trying to get my ball away from the spare tire carrier. I think I probably would have been fine with the next size (shorter) ball mount and still got the job done. The good news is that with the 2 inch drop, I can open the rear door and it just rubs the seal at the bottom of the door a little bit, but I can still easily open the door. I did not want to drop the ball any lower, So this works out well for my rig.
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
# 3
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Everything came as described, and I am so happy with the products and service! etrailer.com is my definite go to!!!
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
# 4
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
solid piece of construction. fits well in 2" receiver
Excellent item delivered in a reasonable time. The items exceeded my minimum needs in many ways.
# 5
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
solid piece of construction. fits well in 2" receiver
Excellent item delivered in a reasonable time. The items exceeded my minimum needs in many ways.
# 6
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
The etrailer.com site was easy to navigate and I found the right draw bar for my new Rav4. The order was processed very quickly and delivery was within just a few days of the order. Prices are fair and customer service was great. Thanks for a great online experience!
Received it exactly when they said it would arrive. Works great. Exactly as described.
# 7
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Quick delivery. Good service. Thank you!
Excellent hitch receiver. Perfect fit, nice welds, easy install.
# 8
Curt Fusion Ball Mount for 2" Hitches - 1-7/8" Ball - 2" Rise - 5,000 lbs
Super easy install. I had to use a 12mm tap to clean out years of rust from inside the frame threads that received the hitch bolts. Other than this hiccup the process went smooth. Easy ordering and great customer support.
# 9
Draw-Tite Ball Mount - 4-3/4" Rise, 6" Drop - 10-1/4" Long - 6,000 lbs
It will do the job, for sure.
I recently purchased a class III Curt hitch, mount, ball, wiring harness and hitch pin for my 2011 Toyota Rav 4. The installation was as described, straight forward and easy. The instructions were easy read and matched the vehicle I have. Everything fit together exactly with no modification needed. Shipping was directly to my door. The unit was undamaged and everything was shipped all in the same box. I have used my hitch several times, and although I an new to towing, I look forward to years of use. I did have to make a quiet clamp for the banging mount with an empty trainer, but from what I understand, this is common to all hitched.
# 10
Reese Trailer Hitch Starter Ball Mount Kit
I have not used it yet but looks to be good quality and I'm sure it will be fine
I needed an very specific ball mount(class I, 1/2" rise, 2" ball). etrailer had what I needed in stock and available to ship next day. I had the thing ordered in 60 seconds. Wish I wouldn't have waisted my time and gas shopping at my local hardware stores only to find they didnt have what I needed.
# 11
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
solid piece of construction. fits well in 2" receiver
Excellent item delivered in a reasonable time. The items exceeded my minimum needs in many ways.
# 12
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
The 5 inch rise on this hitch ball mount was perfect for my 07 Toyota Rav4. The rear door opens to the side on this year Rav4 and it has plenty of clearance. I tow a 16 ft aluminium boat and this 5 inch rise ball mount works perfectly on the Rav.
Ordered this product for my 2015 Rav 4 and it has worked perfectly. I tow a trailer about 4 times a week and needed a hitch that would step the ball up to make the trailer level and allow the wheel to be lowered without manually lifting the trailer myself. Product came quickly and was advertised. Would order again if I needed one for another vehicle.
# 13
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
The Curt Class II Drawbar with a 5" rise very nicely solved my problem when hooking up my two trailers to my Rave 4. The trailer jack was as low as it could go when it rested on the ball in my of setup. Now I have plenty of jack room to hook up and unhook. Thanks for your excellent product and service. Ralph E.
# 14
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 15
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
It will do the job, for sure.
I recently purchased a class III Curt hitch, mount, ball, wiring harness and hitch pin for my 2011 Toyota Rav 4. The installation was as described, straight forward and easy. The instructions were easy read and matched the vehicle I have. Everything fit together exactly with no modification needed. Shipping was directly to my door. The unit was undamaged and everything was shipped all in the same box. I have used my hitch several times, and although I an new to towing, I look forward to years of use. I did have to make a quiet clamp for the banging mount with an empty trainer, but from what I understand, this is common to all hitched.
# 16
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
solid piece of construction. fits well in 2" receiver
Excellent item delivered in a reasonable time. The items exceeded my minimum needs in many ways.
# 17
Curt Class II Euro Style Drawbar with 2" Ball - 2-3/4" Rise - 3,500 lbs
Overall I was a little concerned because I had read that shipping was fast but my hitch arrived slower than expected which caused a delay in my plans by weeks. Than when the hitch arrived it had no hinge pin. A little disappointed. I do not take pleasure in writing poor reviews
Nice item however I had to return due to it would be hitting my spare tire on my RAV4. I was not able to install it. On other vehicles with no spare tire on the rear door I think it would be awesome
# 18
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
solid piece of construction. fits well in 2" receiver
Excellent item delivered in a reasonable time. The items exceeded my minimum needs in many ways.
# 19
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Quick delivery. Good service. Thank you!
Hitch installation went well after viewing the installation video. The wiring harness video was not completely accurate but provided more than enough visual information to perform the wiring install in a reasonable time. Overall, very happy with product at this time due to easy install due to seller videos. Haven;'t used it yet other than to take a test drive, so, sorry no videos, Etrailer provides a good product with excellent product support. Shipping was very fast and of course the price was right. I would definitely use them again.
# 20
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Quick delivery. Good service. Thank you!
Hitch installation went well after viewing the installation video. The wiring harness video was not completely accurate but provided more than enough visual information to perform the wiring install in a reasonable time. Overall, very happy with product at this time due to easy install due to seller videos. Haven;'t used it yet other than to take a test drive, so, sorry no videos, Etrailer provides a good product with excellent product support. Shipping was very fast and of course the price was right. I would definitely use them again.
What our customers are saying:
"very easy to shop"