Trailer Brake Controller Specs:
Features:
...x 9/16" tall Mounting range: 360 degrees vertically Limited lifetime warranty Braking Output Braking output is the maximum amount of power that will be applied to your trailer's brakes....
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
...2" tall Length of hardwire pigtail: 30" Mounting: 360 degrees vertically Limited lifetime warranty Gain Power Adjustment You can adjust the gain (also known as output) with the t...
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
...separately) available for select vehicles to reduce installation time Made in the USA Specs: Application: trailers with up to 3 axles (6 brake assemblies) Compatible with electric or electric-over-hydraulic...
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
...Application: trailers with up to 2 axles (4 brake assemblies) Compatible with electric trailer brakes only Dimensions: 5" long x 3" wide x 1-1/4" tall Limited 5-year warranty Easy-to...
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Videos
for Trailer Brake Controller
Help Articles
for Trailer Brake Controller
Expert Answers
for Trailer Brake Controller
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...I've never…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…
view full answer...The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…
view full answer...The number you provided,…
view full answer...The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...