bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Vehicle Lights


  • Installing the Rampage Light bar on a 2020 Ram 1500
  • The Rampage # RA960137 Tailgate Light Bar you referenced is NOT a fit for your 2020 Ram 1500. However, the Rampage # RA960134 IS a confirmed fit for your Ram. The light bar plugs into your 4-pole trailer lighting connector. If your truck does not have this connector you can install the Hopkins # 41155 Simple Wiring Harness. I have included links to these product pages and a review video.
    view full answer...

  • Replacement High/Low Beam Headlights for a Chevrolet Kodiak
  • The Chevrolet Kodiak has two separate headlight bulbs/housings, one for high beams and one for low beams. If you wanted to replace both the high and low beams then you would need two sets of the Vision X Headlight Conversion Kit part # VX-46. The Vision X Headlight Conversion Kit will work as both a high beam and as a low-beam. You don't need to remove any wires, it's all plug and play. The high beam plug on the vehicle will have a different prong configuration than the low beam plug but...
    view full answer...

  • Replacement LED 921 Bulb for Overhead RV Interior Lights
  • The 906/921 LED Bulbs # DI38VR will work great for the overhead lights in your 2008 Itasca Navion motorhome. There's no need to replace the entire light unless you wanted to. Replacing the bulb is much easier and more cost effective. LEDs use less power, are brighter than regular incandescent bulbs and last much longer. As far as the light output compared to the incandescent bulbs, the LEDs are going to brighter, and have a color temperature of 5,500 K. So they will be more white with...
    view full answer...

  • 1141 LED Light Bulbs That Are Warm White and Compatible With Dimmable Light Fixtures
  • The 1141/1156 LED Bulb is compatible with dimmable fixtures and available in a 2-Pack # DI25VR or 6-Pack # DI75VR. These bulbs are the warm white color that you are looking for as well.
    view full answer...

  • Why Wont My Opti-Bright LED Conversion Kit Work on My 1993 Winnebago Brave?
  • I'm so sorry to hear about your Opti-Brite Headlight Conversion Kit - Sealed Beam to LED - 4" x 6" Low Beams # HLL78LB-2 and high beams # HLL79HB-2. I went ahead and brought the issue to my tech at Opti-Brite, and she said that since these lights are plug-and-play, they should immediately work on your 1993 Winnebago Brave. However, it is important to make sure that your current electrical system is providing a power current of 12-24 volts to operate the LEDs. I recommend taking a reading...
    view full answer...

  • Light Bar That Fits A 2022 Ford F-250
  • Yes, we have the Putco Luminix EDGE LED Curved Light Bar # P57VR that is confirmed to fit 2022 Ford F-250s with/without the optional factory fender flares. This light bar has a lumen output of 15,600, has a wattage output of 117 watts, and measures in at 40" long. These LEDs are comprised of premium Nichia LEDs, and features an integrated thermal regulator to prevent overheating.
    view full answer...

  • Replacement Headlights for 2012 Chevy Silverado 2500
  • I can see why this might create some confusion, but it's going to be down to the differences in the types of lights that are used in these vehicles. The 2009 Subaru Ascent only uses a single bulb for both functions where as your 2014 Honda Odyssey and the 2012 Chevy Silverado have separated high and low beam functions, so replacing the lights can be done one at a time or all at the same time. If you check out the front of your 2012 Chevy Silverado 2500 or your 2014 Honda Odyssey you'll...
    view full answer...

  • Is Anti-Flicker Harness Needed for ARC Fog Lights on 2022 Chevy Colorado
  • The correct anti-flicker harness for the H16/5202 LED Fog Light Bulbs # ARC29FR on your 2022 Chevy Colorado is found as the part # ARC98FR on our site. When I reached out to my contact at ARC he said they haven't had anyone call in and say their newer Colorado has needed one yet so they think you'll be okay without it. The note on the product page is a general rule of thumb just so if someone does end up needing that harness they aren't taken by surprise.
    view full answer...

  • Will The Alpena Trailblaze LED Lights Interfere With The BLIS System On My 2018 Ford F-150
  • I emailed Alpena to get some clarification on their Alpena Trailblaze Tailgate LED Lights, part # ALP77229. I was told that the placement of the LED lights will not block or interfere with the BLIS sensors. However, the newer model years of the Ford trucks, may think that a lightbar is really a trailer when they are hooked up to the 4-way connector due to the power draw of the lights. Alpena has not seen that be an issue with the Trailblaze Tailgate LED Lights, but the lights were launched...
    view full answer...

  • Availability Of LED Circuit Board Light With 906/921/194 Base
  • I have an option that will work as a replacement, but we do not have a bulb that has the exact amount of LEDs as the bulb in your picture. We do have the 906/921/194 LED Light Bulb in Warm White # DI76VR, Cool White # DI86VR, or Daylight White # DG65601VP that will work as they use the same 906/921/195 base as the bulb in your picture. I included a few video reviews for you to take a look at.
    view full answer...

  • Are Two H13 LED Headlight Bulbs with Anti-Flicker Harnesses Needed for High/Low Beams on 2019 F-250
  • The H13 LED Headlight Bulbs with Anti-Flicker Harness part # ARC57VR will work as both a high beam and low beam bulb. That said, you would need one kit for the low beam and one kit for the high beam if you were to do both. I have attached a photo below with the required bulb orientation.
    view full answer...

  • LED Replacements For # 93 Incandescent Bulbs
  • A #93 incandescent bulb has a single contact bayonet base, and there are a couple of options for LED bulbs that will replace these. You can choose a bulb that gives off either a warm or cool light; I have added a photo showing the difference between the two bulbs, with the warm on the left and the cool on the right. The correct replacements are the following: - Warm White: 1141/1156 LED Bulb - Single Contact Bayonet # DI25VR - Cool White: 1141/1156 LED Bulb - Single Contact Bayonet...
    view full answer...

  • 194 LED Bulb that is Longer Than CIPA EVO Formance 194
  • For a shorter, white 194 LED bulb we have the part # CM93153 which is considerably shorter than the # ARC68FR that you referenced.
    view full answer...

  • LED Replacement Bulbs For 2011 Toyota Venza And Hyperflashing
  • Hyperflashing occurs because LEDs do not use resistance to create light, as a result this lower resistance is detected by the vehicle as a burnt out bulb. The 3156/3157 LED Turn Signal Bulbs - Wedge Base - 411 Lumens - Amber - Qty 2, part # ARC83FR, will work as a replacement bulb on your 2011 Toyota Venza with the addition of the Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2, part # DI34ZR. I have included product description links and video review links below.
    view full answer...

  • Troubleshooting Bulb 906 LED Replacement for Boat Anchor Light
  • The 906/921 LED Bulbs - Wedge Base - 360 Degree - 215 Lumens - Warm White - Qty 2 # DI68VR sounds like it isn't the best fit for your application. The style sounds like to doesn't allow enough room for your application so I recommend using the 921/906 LED Bulbs - Wedge Base - 360 Degree - 230 Lumens - Warm White - Qty 2 # DI74ZR which has a longer taper to the base allowing for proper seating.
    view full answer...

  • Recommended Light For Back Of Snowmobile Trailer To Help Backing Up In The Dark
  • While the Optronics LED RV Exterior Scene Light - Submersible - 1,200 Lumens # UCL41CB is pretty bright at 1200 lumens, it would not be the most ideal for lighting up behind your snowmobile trailer to back up in the dark. Instead I recommend going with the MaxxTow Off-Road Light Bar - LED - 72 Watts - Mixed Beam - 2 Row - 12" Long # MT80631 which has 5280 raw lumens and has both spot beam and flood beam lights to lighting up a long distance while still lighting up around you and would...
    view full answer...

  • Does Rampage SuperBrite LED Tailgate Fit 2016 Ram 1500
  • The Rampage SuperBrite LED Tailgate Light Bar # RA960134 is a confirmed fit for your 2016 Ram 1500 and does not require any adapters based on how your vehicle is optioned as well.
    view full answer...

  • Bargman Incandescent - LED Replacement Bulb Possible?
  • The Bargman 8.5" x 4.5" size is fairly common in trailer tail lights. It uses an 1157 bulb, which we do carry in many LED configurations, such as the # ARC93FR. Replacing the bulb in your current tail light should give you the good results you seek without needing to change out the entire light fixture.
    view full answer...

  • Putco LED Light Bar That Will Work With 2018 Ford F-250
  • There is one light bar from Putco that will work for your 2018 Ford F-250, the Putco Red Blade LED Tailgate Combination Light Bar # P92010-60 which simply plugs into your 4-way. Putco has stated that this system has a new driver which will eliminate any type of code coming on from the tow package, back-up assist or blind spot detection system. They have guaranteed this light bar to work with 2017 and up model year Ford Super Duty trucks (as well as 2015 and up F-150's). I have added...
    view full answer...

  • High/Low Beam Light Replacement and Hitch Recommendation for 2014 Honda CR-V
  • I do have some recommendations for you for high and low replacement bulbs for your 2014 Honda CR-V. We have some that have a white tint while other have a blue tint and I'll list them below but really the only difference is preference. If you want to stick with something a littlre more traditional then go with the white, otherwise the blue looks great too: Premium White High/Low Beam - # VX-DH4 Superwhite (Blue Hue) High/Low Beam - # VX-LH4 Attached are some review videos for...
    view full answer...

  • Can I Wire an Optronics LED Off-Road Light Bar to a 4 Way Connector?
  • You could connect the Optronics LED Off-Road Light Bar # UCL23CB to a 4 way connector like the 4-Pole Trailer End Connector # 18004 in order to allow you to receive power when it is plugged into the 4 way connector on your 2019 Jeep Cherokee, but there is no running light circuit on a 4 way connector so you'd likely need to use the tail light circuit in order to accomplish this. With that being said, this really isn't going to be the best way to accomplish this. You would be much better...
    view full answer...

  • What Replacement 1076 Bulbs do I Need for My 2018 Keystone Laredo?
  • Yes! The replacement 1076 bulbs you need on your 2018 Keystone Laredo are the 1076 Incandescent Light Bulb - Double Contact Bayonet - 23 Watt - Soft White - Qty 2 # DI37VR.
    view full answer...

  • Buyers Products 4-LED Strobe Light In Clear Instead of Amber
  • The Buyers Products 4-LED Mini Strobe Light - Amber Surface Mount part # 3378891130 does come in clear with Buyers Products 4-LED Strobe Light - Clear Surface Mount part # 3378891006.
    view full answer...

  • Additional Driving Lights for 2020 Nissan Frontier With Factory Fog Lights Already
  • I have a solution for additional front lights on your Nissan. The Aries # AA1501262 Light Bar is a confirmed fit for your 2020 Nissan Frontier. While it is not exactly "plug and play" it will mount it your front grill and give you 9800 lumens of addtional lighting - and a customized look. This kit includes all the hardware that you will need for a sturdy installation. I have included an instructional video for your review.
    view full answer...

  • Dimensions of Wedge Base 906/921 LED Bulbs
  • I had the # DI98VR bulbs measured for you and they are about 1-7/16 inches in total.
    view full answer...

  • Is the Vision X Headlight Conversion Kit DOT Compliant
  • I spoke with Vision X and they informed me that the Vision X Headlight Conversion Kit part # VX-57 is DOT compliant. That said, you also need to make sure the bulbs you use are also DOT compliant as these are not included. I have linked some of our H4 bulbs for you as well.
    view full answer...

  • Troubleshooting 3rd Brake Light on Trailer that Flashes with Truck Off
  • It sounds like it's possible that the brake light wire from your 3rd brake light might be coming into contact with the electric brake wire on the trailer. The brake controller on your truck will send an intermentent, extremely small amount of power back to the trailer brakes to check for a connection, and if this wire is connected in anyway to the brake light wire, the power might be enough to activate the light. This is especially true for LED lights, as they require such little power...
    view full answer...

  • Wiring Needed To Use Rampage Light Strip On 2012 Toyota Tundra
  • The Rampage SuperBrite LED Tailgate Light Bar part # RA960134 does connect to a 4-pole flat trailer connector on the Tundra. For that I recommend Curt T-Connector Vehicle Wiring Harness for Factory Tow Package part # C55774 which will allow you to plug into the factory tow port under the bumper and gives you a 7-way plug and a 4-pole flat to plug your light strip part # RA960134 into. You can use both the 4-pole and 7-way functions at the same time as long as you don't overload the circuit...
    view full answer...

  • Will Vision X Fog Lights Fit 2017 Ram 1500 Truck
  • The Vision X Optimus Single Prime LED Fog Light Upgrade Kit, part # XIL-OE0913 will work great on your 2017 Ram. These LED lights measure 3-inches wide x 3-3/16 inches tall x 3-13/16 inches deep and have a total effective lumen output of 2,944. These lights come with custom mounting brackets made of 304 stainless steel.
    view full answer...

  • Does Hopkins Bulb with Audible Backup Alert Meet SAE J994 and OSHA Requirements
  • I reached out to my contact at Hopkins who confirmed the Backup Alert with Audible Alert, part # HM20101VA does not meet either of those requirements. For a backup alarm that does meet OSHA and SAE J994 regulations as well as GSA, the U.S. Bureau of Mines and all state regulations, I recommend the Buyers Products Self-Grounding Back Up Alarm, part # 337BA107. We don't carry a backup alert that can be used to replace an existing vehicle bulb which would meet the above regulations and...
    view full answer...

  • Can you Change the Strobe Pattern on the Round LED Strobe Light # 337SL40AR?
  • The Round LED Strobe Light # 337SL40AR is a great option to add a high-visibility strobe light for your vehicle or trailer. The strobe light has a 6-flash strobe pattern that cannot be changed to other patterns, but you can use the included black wire to connect to another strobe light to sync their flash pattern together. Check out the video linked below for more details.
    view full answer...

  • Pin Orientation of LED Bulb - Single Contact Bayonet # DI36VR
  • The pins of the LED bulb part # DI36VR that you referenced are 90 degrees relative to the flat surface of the LED panel. Since the panel is directional you would want this to match up properly to your application.
    view full answer...

  • Compatible LED Fog Light Bulbs For A 2019 Toyota RAV4
  • The H11 LED Headlight Bulbs - Single Beam - 1,995 Lumens - Cool White - Qty 2 # ARC89FR are a confirmed fit for your 2019 Toyota RAV4. These bulbs will install in the same holes as your factory fog light bulbs and will require the Anti-Flicker Harness for ARC H11 LED Bulbs # ARC66FR to function. This wiring harness will also help to cool the bulbs as they will get hot. I've attached an installation where Shane will walk you through installation of these items on a similar vehicle. I've...
    view full answer...

  • Can an LED Light Strip Be Wired to Rear of Trailer
  • About how big of a light are you looking to install? What function do you want the light to carry?
    view full answer...

  • Difference Between Vision X H13 Bulb Colors of Super White and Premium White
  • The difference between the two is that the # VX-LH13 which is super white has a temperature of 5,300 K and premium white # VX-DH13 has a temperature of 4,300 K. The higher the number the bluer the color will seem. So the # VX-LH13 will be a bit bluer than the # VX-DH13 which will seem whiter.
    view full answer...

  • Do the End Caps Rotate on the LED Replacement Bulb for T8 Fluorescent Light part # DG526131VP
  • The LED Replacement Bulb for T8 Fluorescent Light part # DG526131VP gives off light 360 degrees this eliminates the need for rotating end caps and uses the standard reflector on the current light housing to project the light in the desired direction.
    view full answer...

  • Can 1157 Incandescent Bulbs In a Trailer Tail Light Be Replaced With LEDs
  • In general, yes, most incandescent bulbs can be swapped out for an LED. In order to do this you need to know the bulb type such as 1157. That said, when replacing incandescents with LEDs you must use the same color bulb as the lens in order for the light to show through properly. For example, if you were replacing a tail light bulb behind a red lens then you would need to use part # ARC63FR.
    view full answer...

  • How to Adapt the Putco Strip Light part # P92009-48 to Fit Vehicle 7-Way
  • The wiring of the Putco Strip Light part # P92009-48 is a 4-way for the taillight functions and then a separate white wire that gets ran to the reverse light circuit since that's not carried on a 4-way. So what you would want to do is cut off the 4-way of this and wire the light's wiring to a 7-way like # A7WCB according to the chart I attached.
    view full answer...

  • Adding LED Pod Lights to Trailer Rack
  • Adding LED pod lights to your trailer's rack system will require an auxiliary power source such as a 12 volt battery that you will need to mount on your trailer and wire the lights to. The Vision X Optimus Round Prime Pod Light Kit # XIL-OPR120KIT which has a wide spot beam or the Vision X Optimus Round Prime Pod Light Kit # XIL-OPR110KIT which has a narrow spot beam has the wiring and switch included in the kit. If you take a look at the accompanying photo you can see how these lights...
    view full answer...

  • Overall Brightness of LED Conversion Headlights Compared to OEM on 2015 Jeep Wrangler Unlimited
  • The 2015 Jeep Wrangler Unlimited uses a different style connection than the Opti-Brite Headlight Conversion Kit - Sealed Beam to LED - 7" Round - Aluminum Housing # HLL93HLB-2. To get a light that has the wiring conversion you need, I recommend the Vortex Headlight Conversion Kit - Sealed Beam to LED w/ Halo Ring - 7" Round - Chrome # XIL-7RDKITJK. The converter is an important part of the conversion from Factory wiring to LED. We don't currently have a wiring converter for the Opti-Brite...
    view full answer...

  • Light Bar For Enclosed Trailer To Work Outside of Trailer At Night
  • The MaxxTow Off-Road Light Bar part # MT80636 can be used in your enclosed trailer if you wire the light bar to a 12V battery. It is typically used as an off-road light bar but works for your application. It is a combination flood beam and spot beam for seeing at a distance. I have attached a photo of our installers testing the light in the parking lot. I recommend Go Power Smart Battery Converter Charger part # 34266169. The Go Power Converter is a 55 Amp Converter. When choosing...
    view full answer...

  • Do EVO Formance 1157 Lights # CM93236 Work the Same as Dual Filament Incandescent Bulbs
  • The EVO bulb set # CM93236 is classified as an 1157 which, if it was incandescent, would be a dual filament. So it does have the same functions as a dual filament 1157 incandescent bulb.
    view full answer...

  • Why Isnt My Opti-Brite Headlight Conversion Kit # HLL79HB-2 Working?
  • I'm sorry you are having trouble with your lights! I went ahead and looked up your order with us, and it looks like you bought the Opti-Brite Headlight Conversion Kit - Sealed Beam to LED - 4" x 6" # HLL79HB-2. Since these lights come in with a simple plug-in style, one of the most common issues is a blown fuse. In order to find out if this is the case, I recommend consulting with your Winnebago owner's manual to discover the location of the particular fuse that corresponds to the headlights....
    view full answer...

  • Is The ARC 93FR A Direct Replacement For the 1157 Bulb
  • According to ARC, the manufacturer, their # ARC93FR LED bulb is the proper replacement for a dual filament 1157 taillight bulb which provides the turn signal, taillight and brake lamp.
    view full answer...

  • Does The Buyers Products Incandescent Strobe Light # 337SL500A Have 2 Flash Patterns
  • I spoke with the manufacturer, Buyers Products, and didn't get a straight answer on how the Buyers Products Incandescent Strobe Light # 337SL500A has two flash patterns so I went out to the warehouse to verify it for myself. After looking at this light I was unable to find any sort of switch or button to press to switch strobe patterns. Since it clearly only has one strobe pattern I've had this changed to 1 pattern and the video you referenced will be updated. If you look this product up...
    view full answer...

  • Where Are The MaxxTow Off-Road Lights Made
  • MaxxTow Off-Road Lights part # MT70882 are made in China. Even so we have received good reviews on the lights regarding their quality and brightness. I have attached a photo and video for your reference. The only option that we carry that may work for you that are made in the USA are the Peterson flood lights. The Peterson Great White LED Work Light part # 910-MV measures 3-7/16" wide x 3-1/2" tall but is a bright white light compared to the soft beam of the MaxxTow. There is also...
    view full answer...

  • Recommended LED Light Bulbs For Vanity With BA15s Base And 1139 Fitment
  • You will want to go with 1141/1156/1003 LED Light Bulb - BA15s - 180 Degree - 270 Lumens Qty 2 which comes in Warm White # DI46VR or Cool White # DI66VR (see demonstration video for comparison). These bulbs use the BA15s base and is the same fitment as 1139 bulbs. These are bright LED bulbs which would work well for your application.
    view full answer...

  • Does Optronics Unitek LED Directional Lights # 826LED Have Switch
  • The Optronics Unitek LED Directional Lights # 826LED that you referenced does not have switches. You'd wire them to a switch to activate them as needed. For a switch you could use the part # D16740.
    view full answer...

  • Will Putco Red Blade LED Tailgate Light # P92010-60 Work on 2020 GMC Sierra 2500
  • Yes, the Putco Red Blade LED Tailgate Combination Light # P92010-60 that you referenced will fit and work great on your new 2020 GMC Sierra 2500. This is indeed the new/current model of their Light Bar and it does feature an upgraded design that was specifically engineered so that it doesn't interfere with or trigger error codes with regards to existing towing packages. I have attached a short video review that you can check out as well.
    view full answer...

  • Lumen Rating of the 921 Putco Metal LED Bulbs # P340921W-360
  • I reached out to my contact at Putco who said that the Putco Metal LED Bulbs # P340921W-360 you referenced are rated at 600 Lumens.
    view full answer...

  • Troubleshooting Rampage SuperBrite LED Tailgate Light Bar Left Brake Light
  • I took a look at the instruction manual and in order to troubleshoot what the issue is with the Rampage SuperBrite LED Tailgate Light Bar # RA960137, "If you have issues with the functions of the bar check the 1 amp fuse in the ground line. You can use a 9 volt battery to test power off of the vehicle. Connect the battery (-) to the ground on the four prong, and the other (+) to each of the three connectors on the four prong, one at a time. This will ensure functionality of the bar." It...
    view full answer...

  • Converting Trailer Tail Lights From Incandescent to LED
  • In order to switch your tail lights from incandescent bulbs to LED you will need to know your current bulb type. For example, if you have an 1157 bulb you can use the 1157 LED Tail Light Bulbs # ARC63FR as a replacement. You will also want to make sure that the bulb color matches the lens on your current fixture or the light will not show through properly. I have attached a link to all of our LED replacement bulbs for you to check out.
    view full answer...

  • Will the 3156/3157 LED Tail Light Bulbs Work As Both Brake and Taillights
  • The 3156/3157 LED Tail Light Bulbs part # ARC23FR can be used as a brake, turn, or running light. The exact function it has will vary by vehicle and how the circuit is wired. I don't have any wiring schematics unfortunately for any one particular make/model. That said, I do not believe the brake and running light circuits are on the same bulb for this vehicle.
    view full answer...

  • Fit and Compatibility of Pilot Tailgate Fire Strip to 2009 Ford Escape
  • I was able to go out to the warehouse and measure the Bully Fire Strip LED Light # BLS-1103. The thickness of the LED and bracket is .179 of an inch or 11/64. The overall height of the LED and bracket is .786 of an inch or 25/32 and the height of just the LED portion is .476 of an inch or 15/32. The light strip should not be removed from the housing of which it is incased, this will damage the function of the light and void the warranty. If the above measurements do not suit your...
    view full answer...

  • How To Add a Third Brake Light Camera to an ARE Truck Bed Cap on a 2017 Chevy Silverado 1500
  • I do have options for you but the Rear View Safety Third Brake Light with Camera for Chevy Express part # RVS-913 will not plug into the existing backup camera port on your 2017 Chevrolet Silverado 1500 nor will any camera system we offer. The only camera that will is the factory one that goes to your tailgate. I also cannot guarantee it will work with your factory monitor as it is deigned for a Chevy Express, not a Chevrolet Silverado. The correct camera for your 2017 Chevrolet Silverado...
    view full answer...

  • Does the Optronics LED Light Bar Illuminate the Spot and Flood Lights Separately or Combined
  • No, the Optronics # UCL25CB has only 1 set of wires so the flood and spot beams are designed to work at the same time. We currently do not carry a light bar that allows you to switch between a spot and flood light. You also may want to check out the MaxxTow Off-Road Light Bar - LED - 300 Watts - Mixed Beam - 2 Row - 54-1/2" Long # MT80636, which might fit as well, but I really like that it includes the switch and wiring harness.
    view full answer...

  • What is the Voltage Range for the Optronics LED Off-Road Mini Light Kit LS204RW
  • I reached out to my contact at Optronics who said that the Optronics LED Off-Road Mini Light Kit # LS204RW is designed to be used with a 12V system. He said it could handle some spikes of 13V or possibly 14V but only for short periods of time.
    view full answer...

  • LED Taillights To Replace Existing 8-1/2 X 4-1/2 Incandescent Taillights
  • I have a solution for you, but unfortunately our trailer light manufacturers don't make an LED light that measures 8-1/2 by 4-1/2 inches. The best solution I have for you would be do buy the incandescent lights and swap the bulbs out with an LED bulb. To do this, you would want to use part # 30-92-003 for the left taillight, part # 30-92-001 for the right taillight, and part # DI52VR for the LED bulb to replace the incandescent.
    view full answer...

  • Light Output of Optronics LED Off-Road Mini Light kit part # LS204RW
  • I checked with Optronics and while they don't have a Lumens output for the Optronics LED Off-Road Mini Light kit part # LS204RW they do have a Candela rating for it which is 320. The switch is not waterproof either.
    view full answer...

  • Installing LED Tailgate Light Bar to 5th Wheel Trailer for Additional Light
  • The Rampage SuperBrite LED Tailgate Light Bar # RA960134 will install using automotive grade adhesive tape and will plug directly into a 4 way trailer connector. If you don't already have that 4 way connection, I recommend the Curt Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 60" Wire Lead # C58044. If you need to test functions of your wires behind the tail lights of your trailer, I recommend using circuit tester # PTW2993 before installing your quick splice connectors. I've...
    view full answer...

  • What are the Dimensions of the DI45VR?
  • The 1004/1076 LED Bulb - Double Contact Bayonet - 360 Degree - 210 Lumens # DI45VR measure .664" wide x 1.794" tall.
    view full answer...

  • Voltage Needed to Operate LED 1141 Type Bulb
  • According to Arcon, the # AR50368 lamp is designed for use with 12-volt DC systems. It would work acceptably well in the 11.5-14 volt range. The 13.2-volts DC your batteries will put out with a full charge will not present a problem.
    view full answer...

  • Could the Blazer Flashing Amber Warning Light Bar C4500AW Be Hardwired to Vehicle
  • Yes, if you removed the cigarette lighter adapter of the # C4500AW you would have a positive and a negative wire that you could then use to hardwire the light.
    view full answer...

  • Recommended Tailgate LED Light Bar For 2012 Nissan Frontier
  • For your 2012 Nissan Frontier with 59-5/8 inch tail gate, I recommend using the Rampage SuperBrite LED Tailgate Light Bar - Stop, Tail, Turn, Reverse - 4-Pole Flat - 49" Long, # RA960137. This will allow you to use all the functions you want. I highly recommend hardwiring this to the wires just before your 7 way connector to still give you your trailer connection. You can tap into the running lights, turn signals, brake lights and reverse light functions right there without running extra...
    view full answer...

  • What Light Bars Will Work with the LED Light Mounting Brackets for Rhino-Rack Crossbars
  • I do have an option for you but the Buyers Products Light Bar part # 3371492184 uses a special type of mounting bracket that won't work with the LED Light Mounting Brackets for Rhino-Rack Vortex Aero and Heavy-Duty Crossbars part # RR43174 because there are no mounting holes on each end. Instead, I recommend using the MaxxTow Off-Road Light Bar part # MT80633 which has twice as many diodes and uses side mounting holes so it will work with the LED Light Mounting Brackets for Rhino-Rack Vortex...
    view full answer...

  • Total Length of Diamond Group Festoon Base LED Bulb # DG52628VP
  • I'm not sure of the 31mm but the total length from end to end of part # DG52628VP is 1 inch.
    view full answer...

  • Replacement 14v4w Light Bulb for a 2008 Forest River Berkshire Motorhome
  • In order to determine the correct replacement light bulb for the isle light in your 2008 Forest River Berkshire Motorhome, I would need to know the bulb type and size. In order to find the bulb type and size you will need to remove the plastic cover and look for the bulb number which should be printed on the base. Once this is done I would be happy to inform you of replacement options.
    view full answer...

  • Are Load Resistors Required to Prevent Hyperflashing with Putco Plasma 1156 LED Lights
  • If the bulbs you are replacing on your 2013 Hyundai Azera are incandescent then yes, you will need load resistors to prevent hyperflashing once you install the Putco Plasma 1156 LED Lights # P241156A-360. For load resistors you would want the LED Light Bulb Load-Resistors # DI34ZR. I attached a pic that shows how they install.
    view full answer...

  • Recommendation on Lights For Westin Ultimate Bull Bar
  • The off-road lights that I have available for the Westin Ultimate Bull Bar are as follows: Westin 6 Inch Off-Road Driving Lights, Chrome, part # 09-05001 Westin 6 inch Off-Road Driving Lights, Black Powder Coat - 1 light - part # 09-05051
    view full answer...

  • Availability Of 1156 LED Bulbs That Can Be Dimmed
  • We do offer a few 1156 LED bulbs that are compatible with dimmable fixtures which are the 1141/1156/1003 LED Bulb - Single Contact Bayonet - 180 Degree - 180 Lumens - Warm White # DI36VR which has a color temperature of 3500K, or the # DI96VR which has a color temperature of 5500K. I included videos for each of the products mentioned for you to take a look at.
    view full answer...

  • Will the Opti-Brite Headlight Conversion Kit Part # HLL93HLB-2 Fit a 2005 Jeep Wrangler
  • Yes, the Opti-Brite Headlight Conversion Kit part # HLL93HLB-2 will fit your 2005 Jeep Wrangler. The conversion kit has both high and low beam headlights with a 30,000 hour life. Each light has 11 diodes which will provide greater visibility over the stock headlights on your Jeep.
    view full answer...

  • What Are The Dimensions Of 921/906 LED Light Bulb D164ZR?
  • The 921/906 LED Light Bulb - Wedge Base Cool White # DI64ZR that you were looking at has a plug that measures .349" wide, .109" in depth, and .363" in height. The total height of the bulb is 1.643". I attached a diagram to show these measurements.
    view full answer...

  • Upgrading Headlights on 2020 Honda Ridgeline RTL
  • The base trim Honda Ridgeline RTL uses halogen bulbs for their low and high beams. The low beam has a projector with its bulb, and in other trims, there is a white LED with a projector in there. A popular option for Ridgeline owners who aren't happy with the brightness of their headlights is to upgrade from halogen to LED. I recommend the H11 LED Bulbs with Anti-Flicker Harness - Single Beam - 1,995 Lumens - Cool White # ARC74VR. It is designed to replace halogen low-beam headlights,...
    view full answer...

  • Does Optronics LED Off-Road Light Bar Have Specific Range
  • While there is not a specific range that is specific to the Optronics LED Off-Road Light Bar # UCL22CB I can give you some comparisons that may help. If you take a look at the accompanying photo you can see a test we did with the MaxxTow Off-Road Light Bar # MT80633 (which also fits your 2012 Ram 1500) that shows the lights at approximately 100 feet. I offered this comparison because the MaxxTow and Optronics light bars are very similar mixed beam off-road lights. The MaxxTow # MT80633...
    view full answer...

  • Are the MaxxTow Off-Road Lights Spot or Flood Lights
  • The MaxxTow Off-Road Lights part # MT80637-2 have a 30-degree projection which would classify them as a spot light whereas flood lights usually have a projection between 45-degrees and 60 degrees. If you want to get a better view of the projection while in use you can take a look at the attached review video which shows this @ 3:20.
    view full answer...

  • Recommended LED Lights for 5th Wheel Trailer
  • For the best results I recommend going with all-new LED assemblies for your Grand Design Reflection 5th wheel. While replacement bulbs are an option, you are better off going with a new assembly made specifically to optimize LED lights. Additionally, the LEDs on new assemblies have a lifetime warranty while replacement bulbs have just a 1-year warranty. In terms of brightness levels, brake lights on all vehicles are going to be the brightest because they alert the motorist behind them...
    view full answer...

  • Recommended Halogen Headlight Bulb for 2010 Toyota FJ Cruiser
  • The Vision X H4 Halogen Headlight Bulbs - Premium White - Qty 2 # VX-DH4 are 55 watt Halogen bulbs which would make them equivalent to about 900 lumens. These will shine 40 percent brighter and up to 35% farther than factory bulbs The Vision X H4 Halogen Headlight Bulbs with Relay Harness - Premium White - High Wattage - Qty 2 # VX-HH4-R are the best viewing bulbs we have for your 2010 FJ Cruiser. They shine up to 45% brighter and up to 40% farther than factory bulbs.
    view full answer...

  • Will Custer Battery Powered Magnetic Amber Warning Light Work in 50 Below Weather in Alaska
  • As you probably know the colder the temperature the harder it is for electrical items to work. The Custer warning light # HF20RL uses LED lights which require less power to operate than regular bulbs so the cold should affect them less. However, given the extreme cold you experience in Alaska it is hard to say how well it, or anything similar, would work. A 50 mile per hour straight line wind could probably move the light. Add snow and ice and it becomes less likely it will be able to...
    view full answer...

  • What Bulb Does the Bargman 30-84-022 Taillight Use
  • The Bargman 30-84-022 Taillights likely use an 1156 type bulb part # DI49VR which is the most common for trailer taillights. This bulb uses a baronet style connection. The bulb type number will be etched into the base of the old bulb for reference.
    view full answer...

  • Dimensions of Putco PURE Universal Side Marker Light # P900003
  • The Putco PURE Universal Side Marker Lights are 4 inches by 2 inches, as you can see in the photo I have edited for you.
    view full answer...

  • Can Lens Be Removed From Optronics LED Off-Road Mini Light Kit - Waterproof
  • Since the Optronics LED Off-Road Mini Light Kit part # LS204RW is considered water proof the lens is sealed and cannot be removed.
    view full answer...

  • Installation Instructions for Rampage LED Tailgate Light Bar # RA960137
  • I've linked you to the installation instruction for the Rampage LED Tailgate Light Bar. The light bar features a 4-pole flat trailer connector that would plug into the existing 4 pole trailer connector on the vehicle. The wiring harness has an extras wire on it that would tap into the reverse light circuit on the vehicle. If your vehicle doesn't have a 4-pole trailer connector, you could remove the 4-pole connector and wire the light bar directly into your taillight circuits. The procedure...
    view full answer...

  • Replacement 1157 LED Bulbs for a Travel Trailer
  • First, what a lot of people do not know about LED lights is that if you are using them behind a red lens then the LED bulb needs to be red as well. Otherwise you will end up with a dim pink light when using white LEDs. LED bulb # P241157R-360 is a pair of red LEDs so they would work well behind a red lens. When used as stop, tail, turn bulbs behind a red lens they are DOT compliant.
    view full answer...

  • Where Should You Install the MaxxTow Off-Road Light Bar on a 2016 Ram 1500
  • The MaxxTow Off-Road Light Bar, part # MT80633, can be mounted anywhere you see fit on your 2016 Ram 1500. That can be on top of the front bumper, behind the grill, or even on the roof. To give you an idea of your different options, I've linked to a video review of this light bar that shows the different setups. We don't have specific pictures of this mounted on a 2016 Ram 1500, but I suggest mounting it the same way as we have on a 2018 Ford F-250. I've linked to that video as well,...
    view full answer...

  • LED Bulb Replacement Recommendation for 912
  • If you have a 912 bulb that you wanted to replace with an LED the part # AR50610 would be what you would need. These would fit and work well. LEDs do not normally create much heat at all compared to incandescent bulbs.
    view full answer...

  • Ways to Fix Hyperflash After Installing LED Vehicle Taillights
  • When you convert lights to LED bulbs like # DI54ZR there is far less power draw, so that can lead to hyper flashing as you referenced. To fix this issue, you simply install a load resistor like # DI34ZR to each circuit that blinks. So both blinker circuits.
    view full answer...

  • Troubleshooting One Time Tow Without Trailer Wiring
  • There is not a way to run full trailer lights without tapping into your vehicle wiring. For a one time tow for about an hour on the highway as you stated, the simple solution is to use a couple of warning lights like the Blazer Amber Warning Beacon - LED - Battery Powered - Magnetic Mount - 4 Flash Patterns # C43A. This will warn people that your trailer lights are not working and allow you to tow your trailer to the destination. I recommend using one on each rear corner of your trailer,...
    view full answer...

  • What Replacement Bulb do I Need for My RV Light Bulb 1076?
  • Yes! We carry the replacement you need. It is either the 1076/1004 LED Light Bulb - Double Contact Bayonet # DI47ZR (warm white) or # DI97ZR (cool white). Both of these bulbs are compatible with dimmable controls.
    view full answer...

  • Magnetic Battery Powered Lights to Be Mounted on a Trailer
  • We do have some magnetic lights that operate on batteries. They're technically emergency lights but they have a constant shine setting. Of course they will not operate as brake or turn signals which I cannot recommend you tow your trailer without. A few examples: # HF18R-HD # HF18R-MB # HF18A-MB You might want to have your truck checked by a mechanic, if you haven't already. I know it will cost more money but if you're paying a shop to perform the repair it should solve the...
    view full answer...

  • Will The ARC 7440/7443 LED Bulbs Get Brighter When Brakes Are Engaged?
  • I spoke to ARC about their 7440/7443 LED Bulbs # ARC95FR, and it will get brighter when the brake signal is run to it. These really are used as brake lights in vehicles and or trailers, so they do have this function built in. Static, or running lights, will run at 300 lumen, but when the brake signal hits it, it will light up to 600 lumen.
    view full answer...

  • How to Install a Light Bar on a 2018 GMC Sierra 1500
  • When installing a light bar like the MaxxTow Off-Road Light Bar part # MT80635 on your 2018 GMC Sierra 1500 you will need to hook it up directly to the battery due to the amount of power it draws. The trailer lighting circuits on your truck would not be nearly strong enough to power the light bar. The good news is however that this light bar comes with an on/off switch so it will not be powered all the time, just when you choose to do so. There may be a way to draw power from the battery...
    view full answer...

  • Replacement LED-Type Trailer Lights for 2003 Ranger Trail Boat Trailer
  • LED-type replacement lights offer a great way to both reduce your trailer's power demands and to make it more visible. LEDs use a fraction of the power, generate less waste heat, require no routine maintenance and offer brighter light output. We have both LED bulb replacements and complete LED-type trailer lighting assemblies. You may be able to simply replace your standard incandescent bulbs with LED equivalents. I linked for you our main page for LED bulb replacements. If you can...
    view full answer...

  • Can Custer Strobe Lights STRL4A be Powered By Running Light Circuit
  • On the Custer 4-LED Strobe Light or Running Light # STRL4A the black wire powers the steady-on running light and if power is applied to the red wire the strobe effect is activated. The white wire is the ground. If you ran the running light circuit of your truck's bed to this light you could have them activate as a solid running light or a strobe depending on which circuit you tapped into. A signal on the red wire will override the steady-on running light signal on the black wire...
    view full answer...

  • LED 1076 Bulb to Replace a 1076 Bayonet Base Incandescent Bulb in RV Trailer
  • Yes, we sure do! The 1076 LED Bulb, # DI95VR, can replace a 1076 single-filament incandescent bulb in your RV, trailer, boat or car. The brightness of this bulb is comparable to a 20-watt incandescent bulb. It is compatible with dimmable fixtures and gives a soft white light, which is warm with a yellowish hue. It has a candelabra bayonet base that you just push in and twist to lock in place.
    view full answer...

  • Compatibility of Headlight Conversion Kit from 4x6 Inch Sealed Beam to Halogen
  • The Vision X Headlight Conversion Kit - Sealed Beam to Halogen - 4" x 6" Rectangle # VX-46 does have 3 prongs, so it should be a direct fit. I've attached a photo of the 3 prong plug to assist. This will replace the OEM part H4651/H4656 and give you up to 30 percent more light. You can get up to 60 percent more light when you pair this with the Vision X 9007 Halogen Headlight Bulbs - Premium White - Qty 2 # VX-D9007.
    view full answer...

  • Is the Vision X Headlight Conversion Kit # VX-46 Sold in Pairs or Individually
  • The Vision X Headlight Conversion Kit # VX-46 that you referenced is sold in pairs.
    view full answer...

  • Can Bargman 92 Series Taillight be Replaced with LED Light
  • I have a solution for you, but Bargman does not offer an LED version of the 92 series taillight assemblies 30-92-002. Instead what you can do is replace the 1157 bulb in the assembly with an LED like the part # P231157R360.
    view full answer...

  • Is the Putco Red Blade LED Tailgate Combination Light Bar DOT Compliant
  • I spoke with Putco about the Putco Red Blade LED Tailgate Combination Light Bar part # P92010-60 and they informed me that this product is indeed DOT compliant even if just used as a third brake light.
    view full answer...

  • Bright LED Light Recommendation for Optronics RV Porch Utility Light
  • I have an even brighter bulb that would fit the # RVPL7C but the part # DG65532VP is too large to fit the housing. For a brighter LED bulb that does fit we have the part # DG526231VP which puts out a warm white color and also puts out 40 more lumens so it is brighter.
    view full answer...

  • How to Attach Magnetic Emergency Light to Aluminum Body Truck
  • I have a perfect solution for you! In order to attach the magnetic Blazer Amber Warning Light Bar # C4850AW to your aluminum body Ford F-250 I recommend using the Buyers Products Magnetic Mounting Plates # 3378895404. These self adhesive magnetic mount pads are specifically designed for applications like yours. They will stick to the aluminum cab using strong 3M tape and provide you with a magnetic surface to which you can mount any magnetic light. We do not have any suction cup...
    view full answer...