I have a solution for you, but the Replacement Hand Controller for Meyer Straight Blade Snowplow # 3371306901 is a replacement controller for Meyer plows and not Fisher. We have 2 available replacement controllers for Fisher plows which I've listed below. It looks like the # 3371306902 is a close match to the one you were initially looking at.
Replacement Hand Controller for Fisher/Western Straight Blade Snowplow # 3371306902
Replacement Shifter for Joystick Control Assembly for Fisher/Western... view full answer...
The Replacement Anti-Wear Shoe Assembly part # 3371303300 for 6" or part # 3371303305 for 7" should fit the Fishers XV2 Snow Plow. However, you will need to confirm this by making sure the post diameter of 1.32" will work for you. I have attached a photo for you with some other measurements to assist as well. view full answer...
For the replacement cutting / lead blade you will want to check out Replacement Cutting Edge # 3371301220 and Replacement Cutting Edge # 3371301291. Both blades are 8' long and 6" tall with 13" between bolt holes just like you wanted. The difference between these blades is that # 3371301220 has bolt holes 1" from the top of the blade while # 3371301291 has bolt holes 2-1/16" from the top of the blade (see attached photos).
Then for the back drag blade the best option available is Replacement... view full answer...
At almost 40 years old it's safe to bet that your Western plow would be considered "old", but obviously still reliable. The difference between the Replacement Control Cable for Western Snow Plow - "New Style" - 9' Long # 3371313010 and Replacement Control Cable for Western Snow Plow - "Old Style" - 9' Long # 3371313005 is the connections on the ends. Both have a ring at one end, but the "Old Style" has a ball connection on the end while the "New Style" is designed to receive a ball type... view full answer...
The kit that you want to use for the Detail K2 snow plow on your 2015 Ram 1500 is part # K281488LB2, when I reached out to Buyers Products about the kit # 3371311110 they said not to use their kit for your Ram pickup. With that being said, I do have a way for you to safely install the Detail K2 light kit on your vehicle. You will need to connect the following wiring to the following functions:
White - Low Beam
Black - Ground
Red - High Beam
Green - Turn Lamp
The current wiring... view full answer...
You are looking for the Replacement T-Frame for Detail K2 Avalanche Snowplows # K2CRM-TFRAME. This will fit into the Main Frame to replace the crossmember on a custom fit plow mount to give you a mount like the Detail K2 Snowplow # K2AVAL8422. view full answer...
The Replacement Control Cable for Western Snowplow # 3371313010 fits the new style of plow cable whether it's the up and down, or the right/left adjustment.
It was hard to track down but I found a diagram that shows the two cables pointed out for you to check out. view full answer...
I did some research on your 2008 Boss RT3-V snow plow, and you are right on the money that the frame assembly is part TFR09708. We fortunately do carry a replacement! The part you need is the Replacement Push Frame Assembly for Boss RT3 V-Plows # 3371304770. This assembly fits Boss RT3-V models 2006 and newer. Unfortunately, with this replacement assembly, we do not carry the mounting hardware for installation. view full answer...
The Replacement Cutting Edge for Fisher Snow Plows # 3371301311 does fit Fisher plows like you have so it should work. It wouldn't require additional holes or drilling but if you wanted to verify you could compare what you have now to the diagram that I attached. view full answer...
The replacement cutting edge you need for a Western Pro S plow that you have is the part # 3371301235. For a back drag plate then you'd want the # 3371311212. For a hardware kit you'd then want the part # 3371301061.
We do not have curb guards though. view full answer...
We have three different replacement spring kits for Snowbear plows.
The Replacement Spring Kit for SnowBear Snowplows, part # SB600-128, replaces the springs for Snowbear snowplows for 60", 72", and 82" wide snowplows.
The Replacement Spring Kit for 84" Wide SnowBear Snowplows, part # SB600-018, replaces the springs for Snowbear snowplows that are 84" wide.
The Replacement Spring Kit for SnowBear 88" Wide Snowplow, part # SB600-021, replaces the springs for Snowbear snowplows... view full answer...
We do have the exact part number you are looking for, which is a shoe tube holder for Fisher snowplows.
The part you were seeking is the Replacement Shoe Tube Holder for Fisher Snowplow # 3371303310.
For two of them you'd just need to enter that quantity on the linked product page. view full answer...
The width between the springs is 1-1/2 inches for the Replacement Double Torsion Spring for Diamond Snow Plow - 4-3/4" Wide x 8-1/2" Long # 3371302160.
There is no weight specification for this spring at a 90 degree deflection. view full answer...
We have the Replacement Single Speed Electric Winch w/ In-Cab Switch for SnowBear Personal and UTV Snowplows part # SB263-282. Unfortunately we do not have the motor by itself as a stand alone. view full answer...
The Replacement Angle Hose Kit for Meyer Hydraulic Snow Plows # 3371304060 will work very well with the Meyers ST 7.5 plow with an E-60 unit. The E-60 regularly puts out 2500 psi and the hoses are rated for up to 5,000 psi. view full answer...
The inside to inside dimension of the # 3371316105 replacement A-Frame is 22-1/4 inches, and the outside to outside mounting ear dimension is 24-3/4 inches. the ears themselves are 1-1/4 inches wide as you can see in the provided photo. If you click the provided link, you can see a product description video featuring this A-Frame. view full answer...
You're absolutely correct. I spoke with the folks from Buyers Products, who confirm that the # 3371311211 back drag edge is indeed 1/4 of an inch thick. view full answer...
The Buyers Products Universal Snowplow Light Kit part # 3371311100 is a complete kit, the lights cannot be purchased separately as they will require the harness to work properly. That said, we do have plenty of other stud/pedestal mounted utility lights that are offered without a harness and could be rigged for a snowplow. I have attached these for you below. view full answer...
The Wireless Handheld Remote for SnowBear Electric Snowplows part # SB263-284 works as a replacement for all SnowBear Electric Snowplows. Therefore, if you have a SnowBear Electric Snowplow then the Wireless Handheld Remote for SnowBear Electric Snowplows will work for you. I spoke with SnowBear and they stated there is not a printed model number on the winch to reference. If you have a SnowBear Snowplow that does not have an electric winch then you would need the Replacement Single Speed... view full answer...
The Replacement Shoe Tube Holder for Fisher Snowplow part # 3371303310 is for a Fisher Snow Plow and replaces the OEM part number 6821. view full answer...
It looks like you've got quick connects on that hydraulic hose, so you can use the Replacement Angle Hose Kit for Meyer Hydraulic Snow Plows # 3371304060 that you were looking at. You will need to remove the broken fittings on the shock in order to install the new ends to get the hose to connect, but this should work for you since it will allow you to easily connect and disconnect the hoses. view full answer...
Replacement Cutting Edge # 3371304761 can be used on either the driver or passenger side of the compatible 8-foot Boss V-plow and it is the same OEM grade as the original edge, according to my contact at Buyers Products. We also offer a Replacement Carriage Bolt and Nut kit # 3371301064 which consists of 10 carriage bolts and 10 nylon lock nuts. view full answer...
The Replacement Skid Shoes for SnowBear # SB600-019 is not a kit, the other parts you are seeing are just the installation hardware which is included with the shoes. This is how the manufacturer makes the snow shoes available to us and we do not have these particular snow shoes available without the installation hardware included. view full answer...
My contact at Buyer's Products tells me that the # 3371311212 is a replacement for Western/SnowEx/Blizzard Snowplows, but they didn't have any infomration as to whether or not the back drag would fit a Fisher HD2 Plow Blade. They were able to send me some dimensional drawings you could compare to the existing hole spacing you have on your blade, which should give you all the information you need regarding fit and compatibility. view full answer...
I have the Replacement Back Drag for Western/SnowEx/Blizzard Snow Plows part # 3371311212 which is 8' long and will match your needs.
To attach it use the Replacement Mounting Bolts for Western Snow Plow Cutting Edges part # 3371301061.
view full answer...
The Replacement Eye Bolt for Meyer, Diamond, and Western Snow Plows part # 3371302005 has 5/8"-11 threads with an overall length of 6". If you can provide the type of snowplow you have I may be able to confirm fit that way but this is unfortunately as much detail as I can provide on these type of replacement parts. view full answer...
The Halogen High/Low Beam Light Kit with Turn Signals for Detail K2 Snowplows - 12 Volts # K281488LB2 will have the following color to function connections:
white=Low Beam
black=Ground
red=High Beam
green=Turn Lamp
My contact at K2 confirmed this. view full answer...
The 1/2" Bolt # 337FCB050013200 will fit with the Trailer Hitch Spacer Block # RP3022, but if you're looking for replacement hardware for a trailer hitch that fits your 2012 Chrysler Town and Country, like the etrailer # e98854, then you actually need 10mm and 12mm bolts that have a hex fitting for the head instead of a rounded head like the 1/2" bolt you looked at.
For a complete replacement hardware set you can use part # RHK and then input your trailer hitch info and we can send you... view full answer...
I confirmed with my rep at SnowBear that the Replacement Wireless Remote # SB263-284 comes with 2-piece setup with a sending/receiving unit that are paired together at the factory. In order to operate the remote with your winch, you need to unplug the old receiver unit and install the new receiver that came with the remote. After you plug in the new receiver unit, the remote will operate. view full answer...
If you have a Fisher or Westin snow plow, all you need to get is this remote # 3371306902 as it will just plug right into the winch harness. If you don't have a plow that's compatible with the remote, you won't be able to add the remote. view full answer...
For your 9 foot Western snow plow the Replacement A-Frame # 3371316215 that you referenced is the correct replacement. Since you have a 9 foot plow you have the Pro series which is what this A-frame is designed to fit. view full answer...
I attached a picture that has all of the dimensions of the Replacement Lift Arm for Meyer Snow Plow # 3371304000 that you referenced. view full answer...
The right hand and left hand springs are different. Since you said you broke the one on the passenger side you need the right hand side part # 3371304848. view full answer...
The Replacement Cross Member Plow Attachment for Detail K2 Snowplows # K2CRM3312 is what is used to connect to the custom fit mounting brackets. These brackets are used instead of a front mounted hitch receiver. I pulled the part from our warehouse and it is a long u-shaped piece made of 2x2 tubing with 2 holes for mounting and 2 tabs along the outer curve. I've attached a photo of a similar tab to help. The bar itself is just over 3-1/2 feet long and has just the two tabs and then... view full answer...
I recommend for your application the Retrofit Kit for SnowBear Winter Wolf Snowplows - 2 Point Hitch Mount # SB324-120 enables you to use your 2 point mounted SnowBear Winter Wolf snowplow with a single front mount trailer hitch receiver.
We will not only match but beat any competitor price on the same item in stock. I've linked the page to our lowest price pledge for you. view full answer...
Yes, the Replacement Pump Unit # 3371306478 referenced in your question is designed to replace the 49211 Western pump, which is what is on your Western Unimount Plow. This will work perfectly. view full answer...
The vertical mounts of Halogen High/Low Beam Light Kit with Turn Signals for Detail K2 Snowplows # K281488LB2 that you referenced attach to the outside of the plow frame. I attached a picture of this kit installed, and while you can't see the attachment point very well you can see that it does attach on the outside of the plow frame. view full answer...
I spoke with my contact at Snowbear and he told me that the kit you actually want is the part # SB324-120 which is the correct adapter for your older SnowBear plow and will allow it to connect to a 2 inch front hitch. view full answer...
The reason a weather cap isn't included for the connection of the two pins of the Replacement Power/Ground Cable for Boss Snowplow # 3371304741 is because due to the way it connects it becomes it's own weather cap since the rubber on the male pin covers the rubber of the female side which effectively seals out the elements.
I attached a review video for this for you to check out as well. view full answer...
I do have an option but there is not yet (May 2020) a Custom Mounting Bracket Kit for SnowBear Hydraulic and Winter Wolf Snowplows for a 2020 Ram 1500. However, you can convert the snowplow from the custom mounting bracket style to the hitch mount style with the Retrofit Kit for SnowBear Winter Wolf Snowplows - 2 Point Hitch Mount part # SB324-120 and then use the Curt Front Mount Trailer Hitch Receiver part # C87FR. view full answer...
The outer diameter of the shaft of the Replacement Anti-Wear Shoe Assembly for Fisher Snowplow # 3371303305 that you referenced is 1.35 inches. view full answer...
I was able to measure some of the mounting holes in the warehouse. I have attached a diagram of the Replacement A-Frame for Western Snowplow - Pro part # 3371316215 for your reference. view full answer...
The Replacement Cutting Edge Half for 8-1/2' Western MVP V-Plow # 3371311200 is the correct replacement cutting edge for your Fisher EZ-V plow that you have. view full answer...
We do have a shoe for a Meyer snowplow with a 3/4" diameter shaft, the Replacement Shoe Assembly for Meyer Snowplow - Standard (Drive Pro) # 3371303002.
I have added a link to a video review with dimensions of this part for you to check out as well. view full answer...
The shaft diameter of the Replacement Anti-Wear Shoe Assembly and Runner # 3371303100 is exactly 1 inch. I have attached an image to assist. view full answer...
Yes, the Replacement T-Frame # K2CRM-TFRAME will take the place of the custom frame mount that you had on your RAMP8219 for attaching to your 2005 Toyota 4Runner.
You will be able to then attach the your snow plow using a CURT Front Mount Trailer Hitch Receiver # C31052 on your 2015 Ford Explorer Limited as long as you do not have an Ecoboost engine. view full answer...
We definitely have the replacement blade for your Fisher snow plow with part 5532. For a compatible replacement, I recommend the Replacement Cutting Edge for Fisher Snow Plows # 3371301300. The mounting holes in this replacement blade accept 1/2" diameter carriage bolts. If you need replacement bolts, you need the # 3371301350. view full answer...
I was able to reach out to my snow plow guy over at Buyer's Products/SAM and he confirmed that the Replacement Center Flap Kit with Hardware for Fisher/Western Snowplow # 3371304410 is a fit for Western MVP v-nose plows. Since the carriage bolts in the spaces where you'll be mounting this center flap are usually a bit longer than the rest of the bolts on the plow, you will be able to mount this with or without a back blade edge. view full answer...
For your Meyer ST-78 Snowplow, we have the Replacement Shoe Assembly part # 3371303005 or just the Replacement Runner part # 3371303015. The shoes are both made of steel so they will work perfectly on gravel which I did confirm with the manufacturer for you. view full answer...
The 5XM5 Universal Cross Member part # SB324-060 that you referenced is a universal adapter that allows you to mount a SnowBear Snowplow on a vehicle with vehicle specific mounting brackets. If you have a SnowBear snowplow then you will need the vehicle specific mounting brackets in addition to the 5XM5 Universal Cross Member if the snowplow you have doesn't already come with it. If your 2014 Dodge Ram Pickup is a 1500 then you will need Custom Mounting Bracket Kit for SnowBear Snowplows... view full answer...
I spoke with my contact at Snowbear and he told me that the kit you actually want is the part # SB324-120 which is the correct adapter for your older SnowBear plow and will allow it to connect to a 2 inch front hitch. Your dimensions listed match what this is designed to fit as well. view full answer...
I attached a picture that shows the install instructions for the Caster Kit for SnowBear Snowplows # SB324-126 that you referenced. view full answer...
The wire gauge of the Replacement Cable and Plug Assembly for Meyer Snowplow part # 3371306115 is 6 gauge wiring. This cable and plug replaces the plug for Meyer snow plows. The ring terminals are fully sealed for moisture. I have attached a review video for your reference. It does not come with a protective cover.
We do have the replacement ground cable for the Meyer Snowplow part # 3371306125 which is a very heavy gauge wire. If you let me know which wire you are trying to replace... view full answer...
The overall height of the shaft for the Replacement Heavy-Duty Shoe Assembly for Western Snowplow # 3371303220 is 8-5/8" and it has a 1" diameter. I have attached a photo showing some other measurements you might be interested in as well. view full answer...
I did some checking and replacement mount # SB324-120 is not listed as a fit for the SnowBear Personal line of plows. Instead you will need # SB324-138 for a SnowBear 82 inch Personal plow. view full answer...
It sounds like you are looking for the Replacement Cutting Edge for Boss Snowplow - High Carbon Steel - 1/4" x 6" x 84" part # 3371304749. I have attached a diagram so that you can make sure the dimensions of your cutting edge is the same. The replacement hardware is part # 3371301060. view full answer...
The black wire of the # K2WR100 does run to the negative post of the battery. I attached a picture that shows how it wires up. The picture might look a bit different since it's an older model but the wiring is the same. view full answer...
Yes. The Replacement Thread King Bolt and Locknut Assembly for Meyer Snowplow - 5/8" - Qty 1 # 3371302020 is a Grade 5 bolt that is 5/8" diameter and has 11 threads per inch. view full answer...
While there are snow plows that fit your 2019 Toyota Tacoma, the SnowBear you referenced not a fit; also keep in mind the only plows that fit your Tacoma do require you to have Curt Front Mount Trailer Hitch Receiver # C31075.
- SnowBear Personal Snowplow for 2" Hitches - Electric Winch - 82" Wide x 19" Tall # SB324-080 or 84" Wide x 22" Tall # SB324-081
You an also use the
view full answer...
I contacted DK2 and they were able to confirm that the Actuator Kit # K2ACT8020 will work to replace the winch on your Summit II Snow Plow. This kit comes with everything you need to install the actuator. view full answer...
We don't have a video that details how to replace the strap of your K2 Winch like part # K2RASP8219, but I did speak to my contact at K2 and he gave me a brief description of the process.
On the winch there is a u-bolt that needs to get removed after feeding the strap all the way out. He said this is pretty obvious and easy to do. Next, there is a pin holding the strap to the spool. On the side of the winch there are a couple of holes. You will need to line the pin up with one of the... view full answer...
The thread pitch on the Replacement Carriage Bolt part # 337FCB050013200 is 1/2"x13.
All of the other replacements that I have available are also the 1/2"x13 UNC. I do not have any 1/2"x20 UNC hardware available. view full answer...
I went out to our warehouse to take a few measurements on the Replacement Trip Spring # 3371302010 that you referenced. I measured an overall length of right at 15". Just the spring itself (without the end hooks) measures just about 11-1/8" long and it has a width of 2-1/4".
I have attached an image below to assist. If you need any other specific measurements just let me know and I will be happy to take them. view full answer...
Yes the thread per inch of the # 3371301062 is 20 since this is a fine thread 1/2 inch diameter bolt. If it was coarse thread instead it would have 13 threads per inch. view full answer...
The closest thing we carry to a complete kit are replacement back drag blades for Fisher snowplows, though these do not have hardware, so you would have to source that locally. The Fisher replacement back drag blades we carry have different lengths depending on the length of your snowplow:
- Replacement Back Drag for Western/Fisher Snowplow - 7-1/2' Long - V-Plow Edge # 3371311215
- Replacement Back Drag for Western/Fisher Snowplow - 8-1/2' Long - V-Plow Edge # 3371311216
- Replacement... view full answer...
Yes, the Replacement Cutting Edge Half # 3371311203 (OEM p# 44997) is the correct replacement for your 8-1/2 foot Fisher XV2. This can be used on either side, so for both sides you'll just need two.
For the replacement cutting edge center steel kit, you can use part # 3371311208 (OEM p# 44894). This includes both the driver and passenger sides as well as the hardware.
view full answer...
The Replacement Quick Coupler for Meyer and Diamond Snowplow part # 3371304025 is a full replacement for the Meyer 15072. There are two threaded ends, one has a male coupler on the end and the other a female. Once both threaded ends are attached you can then easily connect and disconnect by engaging the collar between the make and female couplers. The male and female couplers are designed to be used with each other, not the Meyer or Diamond ones. view full answer...
The coils of the spring part # 3371304717 are .375 inch in diameter, the coiled section measures 8.5 inches long, and from outside edge of hook to outside edge of hook measures 12 inches.
If you could get me the plow model that you have I can see if there's an exact replacement you need.
I attached a review video as well as a link to a page that has all of the springs we carry. view full answer...
Sounds like you have a frame bracket mounted style of Snow Bear plow which means the correct bracket kit you'd need for your 2003 Dodge Ram 2500 is the part # SB397-016 which is a confirmed fit. view full answer...
The Replacement Electric Winch # K2EW8020 is meant to be a replacement for the winch that comes with the snow plows; Rampage K2RASP8219, Rampage II # K2RAMP8219, Storm K2STSP8422, Storm II # K2STOR8422, Summit K2SUSP8826, and Summit II K2SUMM8826.
The Control Box connects to the winch, the battery, and the control button that will be in the cab. This allows operation of the winch without having to get out of your vehicle.
There is an instruction manual for the snow plows that this... view full answer...
We have a mount to use the ATV Bulldog Winch part # BDW78FR with the part # BDW15151 which is a fit for your 2012 Polaris Sportsman 400. view full answer...
We do offer replacement cutting edges for your 8 foot Curtis snow plow, and you can choose from an 8 foot blade that is either 3/8 inch thick or 1/2 inch thick. Both of these replacement cutting edges are 96 inches long x 6 inches tall and have 7 mounting holes spaced 15-1/2 inches apart.
- 3/8 Inch Thick: Replacement Cutting Edge for Curtis Snow Plows # 3371304801
- 1/2 Inch Thick: Replacement Cutting Edge for Curtis Snow Plows # 3371304805
If you need mounting bolts as well,... view full answer...
We don't carry your specific snow plow, but we do have a couple of skid show options that may work for your plow. We have the Replacement Standard Shoe Assembly for Western Snowplow # 3371303200C you asked from, but we also have other options. This skid shoe has a measurement of 6 inches from base to pin and has a 6 inch diameter.
Because I don't have specifics for your plow, I recommend checking all your options on the linked page to assist.
view full answer...
I went out to the warehouse and measured the U-bolt, part # 3371302360. It's a course thread 3/8-16 bolt that measures about 1-15/16 inches long and has about a 1/2 inch opening.
If there are other measurements you need let me know what you're looking for specifically. view full answer...
I reached out to my contact at SnowBear about the Replacement 8-Stroke Electric Actuator # SB263-802 and he said that it has a total lift capacity of 600 lbs and we are looking at 17 seconds with a full load and 3 second no load.
Please note that this is specifically made for the Proshovel # SB324-140, # SB324-168, or # SB324-172 or Winter Wolf # SB324-116, # SB324-166, or # SB324-167 snowplows. view full answer...
The 5XM5 Universal Cross Member for SnowBear Snowplows part # SB324-060 works with all SnowBear Snow Plows, both the older and newer models. I even double-checked some of the dimensions and they are in-line with what you provided. view full answer...
We have trip springs for Boss snow plows like the part # 3371304715 which is 14-1/2 inches long, part # 3371304716 which is 17-7/8 inches long or # 3371304717 which is 12 inches long but the part number you mentioned fits a different brand. view full answer...
The Custom Mounting Bracket Kit for SnowBear Hydraulic and Winter Wolf Snowplows part # SB397-133 is indeed a SnowBear product. The mounting bracket kit is a direct fit for your 2015 Chevy Colorado and will not require any additional cutting, drilling, or grinding in order to install.
The universal crossmember you are referring to is the 5XM5 Universal Cross Member for SnowBear Snowplows part # SB324-060. If the snow plow you currently have does not already have this mount then yes,... view full answer...
I checked with Buyers Products and they confirmed for me that the low beam of the Buyers Products Universal Snowplow Light Kit # 3371311100 is an H7 bulb like the # P230007NW and the high beam is an H1 like # CM93385. To access the bulbs to replace them you'd remove the four nuts on the back of the housings. view full answer...
Yes, since all Snowbear Winter Wolf plows use the same 31-inch spacing for their mounts you can use their adapter # SB324-120 to allow use in your 2-inch hitch. view full answer...
You will not need the Universal Cross Member for SnowBear Snowplows # SB324-060 when mounting the SnowBear Winter Wolf Snowplow # SB324-167 on your 2012 Jeep Liberty 4 x 4. The only thing you will need is the Custom Mounting Bracket Kit # SB397-056. I've added a link to a video review of this plow for you to take a look at. view full answer...
The distance between the two dowels on the SnowBear 5Xm5 Universal Cross Member # SB324-060 is approximately 32-3/4 inches. This fits all models of SnowBear plows like what you have so it would work well for you. view full answer...
I checked with Meyer and their tech said there are several versions of the E-58H hydraulic pump but based on the details he provided kit Replacement Angle Hose Kit # 3371304060 should work fine for all versions. This kit includes both threaded right-angle and quick couplers. view full answer...
We have just what you are looking for.
The replacement skid shoes for your K2 Summit snowplow are part # K2SS2600. These will work with the Summit or Summit ll plow. This comes with the mounting brackets and hardware you need. view full answer...
The distance between the two dowels on the SnowBear 5Xm5 Universal Cross Member # SB324-060 is approximately 32-3/4 inches. The diameter of the dowels themselves is 1-5/8 inches and they are just about 4 inches in height.
This cross member is designed for SnowBear Plows and will install between the 2-point vehicle specific mounting brackets and the snow plow itself. view full answer...
The overall length of the Replacement Spring with Eyebolt for Detail K2 Rampage Snowplows # K2SPR1082EYE is 13 inches, and is 2 inches wide. view full answer...
The Replacement Electric Winch for Detail K2 Snowplows, # K2EW8020, has a line pull speed of 14ft per minute at zero load and 10.5ft per minute at 600lbs. This winch will draw 10 amps at zero load and up to 45 amps at 600lbs and the included strap is just over 2ft long. view full answer...
While my contact at SnowBear was not able to get me the dimensions you asked about they were able to tell me that the Replacement Scraper Blade # SB324-066 that you referenced is designed to fit the older and newer models of their plows so they guaranteed it will work for you. view full answer...
The Replacement Scraper Blade # SB324-065 is 82 inches long and about 2-1/2 inches wide. It's a direct fit for the following snowplows:
SnowBear Personal Snowplow # SB324-080
SnowBear Proshovel Snowplow # SB324-168
SnowBear Winter Wolf Snowplow # SB324-166 view full answer...
I spoke with my contact at Detail K2 about Replacement Spring # K2SPR1082EYE. The overall length is 13 inches, width is 2 inches, and the diameter of the steel used is approximately 1/4 inch. view full answer...
The 5XM5 Universal Cross Member for SnowBear Snowplows part # SB324-060 measures around 33" long x 2-3/4" wide. The distance between the two dowel pins is 30-1/8". Please note, the 5XM5 Universal Cross Member for SnowBear Snowplows is only to be used with SnowBear Snow Plows. view full answer...
If you wanted to remove the yellow caps of the Replacement Snow Plow Guides # 3371308300, cut the guides shorter and then reinstall the yellow caps you certainly could. view full answer...
In order to install the Off-Road Lighting Kit for SnowBear Snowplows part # SB324-127 on your SnowBear Hydraulic Snowplow you only need to use the lights and wiring. The mounting brackets are for the electric plows and will not be used for installation on the hydraulic plow.
For starters you will need to line up the two mounting holes on the light with the two mounting hole on either side of the crossbar used to secure the plow to the vehicle. You can then use the provided hardware to... view full answer...