Filter Results

Filter Questions and Answers:

reset filter

Expert Answers about RV Vents and Fans


  • Damper Recommendation for Ventline S0721 Series RV Range Hood on 2017 Coachmen Apex Nano
  • Since your wall thickness is 1-3/8 inches the damper you'll want is the deeper part # V2111-13 which is 1-3/4 inches. This will allow you to trim it back as needed so that it fits properly with the Ventline S0721 Series RV Range Hood # S0721-20BD-F-1.
    view full answer...

  • Circuit Tester for Determining Function of RV Vent Hood Wiring
  • Since it is unlikely that even the maker of your 1996 mobile home will know the wiring color scheme for installing a replacement kitchen vent hood, your best bet is going to be testing the wiring with a probe tester like # ALL640595. This will help you confirm which wire in the RV is ground and which is 12V hot. The Fan-Tastic Vent Roof Vent # FV801250 that you referenced uses WHITE wire for GROUND and a BLACK wire for +12V.
    view full answer...

  • Will Lid From Fan-Tastic Vent Make Contact with Ultra Breeze Vent Cover # FVU1500GR
  • The Ultra Breeze Trailer Roof Vent Cover # FVU1500GR referenced in your question is designed to work perfectly with any Fan-Tastic roof vent with model numbers that start with "FA" or "FV" including motorized units like the part # FV801250. As long as this is what you have there will be no interference between the lid of the vent (whether open or closed) and the inside housing of the Ultra Breeze Cover. I also verified this with my contact at Fan-Tastic Vent. The Ultra Breeze Cover...
    view full answer...

  • How Tall are the Tabs on the Vent Cover for Jensen Trailer Roof Vents 63112
  • The height of the tabs that the hinge goes through on the Vent Cover for Jensen Trailer Roof Vents part # 63112 is right around 3/4" tall. We do not have any four point replacement lids with 1-1/8" tall tabs so if the above will not work for you then the only other option we have besides a replacement vent is the MaxxAir UniMaxx Universal Replacement Lid part # MA00-335002. The height of the tabs however should not cause the lid not to fit. The only two things you need to match is the size...
    view full answer...

  • How Many Wires Run from the Switch to Fan on the 42 Inch Ceiling Fan for RVs
  • In regards to the 42" Ceiling Fan for RVs part # 324-000053, there is a blue wire on the switch that gets ran to a blue wire on the motor of the fan as well as a white wire on the switch that gets ran to a white wire on the motor of the fan. Therefore, you will only need to run two wires from the switch to the fan. Please keep in mind that there are also two other wires on the switch (black and red) that get ran to power and ground as well as one other wire on the motor of the fan which...
    view full answer...

  • How to Choose the Correct Vent Cover
  • I can certainly point you in the right direction on how to select a vent cover for your trailer, although there isn't a way for us to know what vent you have as those type of records are not available. While the easiest way would be to see if you can find a model number of the vent on your trailer and find its replacement cover that way there is another option. What you will need to determine first is the type of hinge you have on your roof vent; if you take a look at the accompanying...
    view full answer...

  • Is the Valterra Heating and A/C Vent Register A10-3350VP Air Tight
  • The Valterra Heating and A/C Vent Register part # A10-3350VP like most vent covers is not completely air tight. There will still be a bit of air that can escape through the vent while closed. This is very common for duct work either in a home or RV. If the above vent is not as air tight as you would like then you may want to consider a different style, the Valterra Heating and A/C Vent Register part # A10-3349VP which has an off white color but will form a better seal. I have attached...
    view full answer...

  • Remote Compatible with Roof Vent with Fan and Powered Lift
  • The Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat - Powered Lift - 14-1/4" x 14-1/4" # FV803350 unfortunately does not have a receiver so a remote for that fan/vent is not an option. You can hardwire it to a switch, but that only will give you the fan speed or power options. To get the remote feature you would need one of the following vents: Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote - Powered Lift - 14-1/4" x 14-1/4" # FV807350 MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat,...
    view full answer...

  • Can a Variable Speed Motor be Added to the Ventline Vanair Trailer Roof Vent
  • I am sure you could install a variable speed motor on the Ventline Vanair Trailer Roof Vent part # VP-543SP but the manufacturer, Ventline (Dexter) does not recommend this nor would they honor any warranty claim if done so. The only powered vent fan options we offer with variable speed motors are the 14" long x 14" wide models like the MaxxFan Roof Vent w/ 12V Fan part # MA00A04401K.
    view full answer...

  • Outer Dimensions of the MaxxAir MaxxShade Roller Shade
  • I went out to the warehouse and found that the outermost dimensions of the MaxxAir MaxxShade Roller Shade # MA00-03900 are 18-3/4" x 19-1/2" as you can see from the attached photo. Please note that these dimensions are from the underside of the unit. I have also linked a review video for you to reference.
    view full answer...

  • Installation of the Hugger Style Ceiling Fan to Light Switch
  • The 42" Hugger Style RV Ceiling Fan with Light Kit for RVs - Brushed Chrome # 277-000081 you asked about will work well with your light switch for the light and the pull for your fan speeds. When installing you will see that two of the wires (blue and white) will be run to the switch and then the other wire and the ground (green) will be separate. The fan will most likely have the constant power from the other power and neutral wire (black and white). That means the fan will be able...
    view full answer...

  • Replacing Skylight over Shower on RV Roof
  • To replace a skylight, you will follow the same installation as you would for a standard RV vent like # V2092SP-28. We do not have any skylight replacements available, but you will install a replacement using the Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White # 344270KITW. Screws and sealant will hold the skylight in place and make it weather tight.
    view full answer...

  • Solution for Needing Replacement Circuit Board for V2510 Northern Breeze Roof Vent
  • My contact at Ventline confirmed that the issue you're having with your model V2501 Northern Breeze 12V fan is related to the controller circuit board. The switch itself is not the problem. Unfortunately, he advised that replacement circuit boards are no longer available as this item went out of production back in 2009. In this case you'll need to install a new fan assembly to replace the existing unit. The Ventline Ventadome roof vent part # V2092SP-28 that you referenced would be...
    view full answer...

  • Exhaust Fan Recommendation for Ambulance
  • The Ventline Vanair Trailer Roof Vent # VP-543SP you referenced was actually designed for what you are looking for. It can move 100 CFM of air to the outside of a vehicle which would work well for what you mentioned wanting. You'd need to wire it to a 12 volt power source on a switch and you'd be set.
    view full answer...

  • Voltage for Powering 42 Hugger Style RV Ceiling Fan for RV # 277-000082
  • The Airrforce ceiling fans like the # 277-000082 use 120 VAC power like what a house would use. It does not use 12 volt DC power like what vehicles use. For a 12 volt fan we have the # 324-000056.
    view full answer...

  • Can Direction of Air Flow on Ventline Vanair Trailer Roof Vent Fan part # VP-543SP be Reversed
  • We've spoken with Ventline and if you reverse the polarity of the wiring on the Ventline Vanair Trailer Roof Vent w/ 12V Fan part # VP-543SP you can reverse the direction of the fan. If you wanted a switch to change the direction you'd need a DPDT switch found locally at a hardware store.
    view full answer...

  • Vent Cover Needed for a Ventline V2094 Vent
  • Do you have an older V2094 vent? The part # BVD0449-A01 that you referenced fits V2094 vents post-2008 while the part # BV0554-01 is for V2094 vents pre-2008. If you have an older V2094 vent then this is the vent cover you are needing. This has a continuous metal hinge like what you mentioned. I have linked a review video and a picture showing what it looks like for you to reference.
    view full answer...

  • Replacement RV Vent Cover Lid with UV Protection
  • There are a number of different trailer vent styles that come down to hinge fit. I tried to look up your order history to see what cover you purchased, but there wasn't a cover connected to an order from the email address you asked the question from. It is definitely not normal for a lid to only last 3 years without other factors outside of UV rays and all the covers we carry have UV protection so I'm sure we can find something that will work better for you. I believe the Replacement...
    view full answer...

  • Wireless Remote On/Off for Fantastic Roof Vent Model 1250
  • The Fan-Tastic Vent Roof Vent w/ 12V Fan - Reversible - Manual Lift # FV801250 does not have a remote option. You could add a wireless relay switch for the basic on/off function by interrupting the 12v power and leave the fan switch on. Unfortunately we do not carry any at this time and most of these aftermarket relays come with a key fob versus a remote. If you want a similar fan with remote, I recommend the Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote - Powered Lift # FV807350....
    view full answer...

  • How Does Greystone Range Hood Attach
  • The Greystone Range Hood # 324-000086 does not have a plug, it is a two-wire design. The black wire is for power and the white is for ground. It is designed for RV's and can be vented to the outside, as it does have a vent in the rear. I have added a link to a video review which I strongly recommend checking out.
    view full answer...

  • Locating Replacement Roof Vent Lid for Forest River 3251 DSLE
  • Based on my research it looks like your Forest River 3251 DSLE RV is equipped with a standard tinted roof vent lid like # FVK1020-19, however I was unable to track down what type of hinge it uses. Replacement 14 x 14 inch standard vent lids will typically have a 3-point hinge, a 4-point hinge, or a metal/plastic continuous hinge. I have attached an image to clarify the different styles. In order to choose a replacement lid that will fit you will just want to take note of the hinge on...
    view full answer...

  • Replacement Motor Gear for RV Bathroom Roof Vent
  • The only replacement motor gear we have available for RV roof vents is the Ventline # BVD0121-00. This fits the Ventline Ventadome model V2119 and is the gear that transfers power from the motor to the operator for opening and closing the vent. If this is what you have then the gear will work perfectly. I was unable to cross-reference the numbers you found on the gear motor with any of the parts that we have available.
    view full answer...

  • Replacement Roof Vent Cover for Sundowner Horse Trailer
  • The replacement vent cover for your Sundowner horse trailer can be different as vents are often changed over the years by manufacturers. The vent cutouts remain consistent because there is an industry standard size so replacements are available but the hinge design may be different. I've attached the link to all your cover options to assist as normally a quick glance will help you determine the style. I've attached a photo to assist. If you want to send a photo of the vent cover,...
    view full answer...

  • Fan Blades on Ventline Range Hood are Going the Wrong Way
  • The Ventline range hood, part # S0721-20BD-F-1, is designed to pull air from the RV and vent it outside. If yours is running in the opposite direction it sounds like you may have the wires reversed which would cause the fan to go in the opposite direction. The black wire is positive and the white wire is negative. On the motor the black wire should be on the side with the red mark.
    view full answer...

  • Height of Garnish on the MaxxFan Deluxe Roof Vent w/ 12V Fan Part # MA00-06200K
  • The piece you are referring to on the MaxxFan Deluxe Roof Vent w/ 12V Fan part # MA00-06200K is called the garnish and it is 5-3/4" tall but can be trimmed to fit if needed.
    view full answer...

  • Could MaxxFan Deluxe Roof Vent # MA00-07500K Mount Horizontally
  • The MaxxFan Deluxe Roof Vent # MA00-07500K that you referenced would technically function just fine mounted on it's side but it's unknown how well it would seal out water in the event it rains.
    view full answer...

  • Overall and Mounting Hole Dimensions for Ventline Exterior Wall Vent for RV Range Hood V2111-03
  • The dimensions of Ventline Exterior Wall Vent for RV Range Hood # V2111-03 are shown in the linked photo I prepared for you. Mounting hole spacing is also indicated. Overall edge to edge dimensions are 5-1/4 x 11-5/8-inches and the vent fits an RV wall opening of 10-1/4 x 3-1/2-inches. Mounting screws # 31071 and white silicone sealant # 0160297 to complete the installation are sold separately. The sealant can be used as both an adhesive (by placing a narrow bead on the mounting...
    view full answer...

  • How to Disable Rain Sensor Feature on MaxxAir MaxxFan RV Vent MA00-04500K
  • It sounds like you have the MaxxAir MaxxFan RV Vent with rain sensor # MA00-04500K. This sensor consists of a small circuit board, which is shown in the linked photo. This could have failed, perhaps from damage from an impact from a tree branch or something like that. You can try turning this feature off. On the vent's keypad there is a button that allows you to disable the rain sensor feature. This is noted by an arrow in the second photo.
    view full answer...

  • Maxxair Fan Deluxe Roof Vent # MA00-07500K Height When Open
  • When the hood of the MaxxAir Roof Vent part # MA00-07500K is fully open the vent extends 9-15/16 inches above the roof. When closed it's instead 5 inches.
    view full answer...

  • Replacement Fan Blade for an Elixir S545A3 Roof Vent
  • Elixir is no long in business so replacement parts are extremely hard to find. I did some research online and was not able to locate a replacement fan blade that would work with the d-shaped shaft on your vent. Insead, the best option for you is really going to be to replace the entire assembly for which I recommend using the Ventline E-Z Lift Ventadome Trailer Roof Vent part # V3094-601-00C. This is currently the most cost effective option we have for you. It will fit the same 14-1/4"x14-1/4"...
    view full answer...

  • How to Remove an Old Roof Vent Cover
  • There are a few different types of roof vent covers and the type of hinge they have is going to dictate how they are removed/installed and the tools required to do so. If your Haulmark trailer has a roof vent with a continuous hinge then you will most likely need a screwdriver to remove the screen/support arm and then a pair of pliers to slide the hinge out of the track. I have attached an install video on a roof vent with a continuous hinge for you. If you can let me know what type...
    view full answer...

  • Replacement Range with Fan and Light for an RV
  • It sounds like you are looking for a new range hood for your RV. If that is the case then we have several options for you. In order to choose the correct replacement I would need to know the size of the unit you have now. We currently have options for 20", 22", and 24" wide ranges. I have attached these options for you below. They all have a light and 12 volt fan and they are available in white, black, and stainless. 20" Wide x 12" Deep: Black- part # S0721-20BD-F-1 White- part #...
    view full answer...

  • Best Storage and Roof Vent Cover for 2018 Winnebago Micro Minnie 1700BH
  • Thanks for the photo. It looks like you have a continuous hinge which means the Replacement Dome Assembly part # BVD0449-A03 should be an exact replacement for your 2018 Winnebago Micro Minnie 1700BH. For a storage cover, you will need one to hold up in both snow and rain so the best option we have for you is the Adco RV Cover w/ Tyre Gards for Travel Trailers part # 290-34841. This cover also comes with wheel guards and it has a three year warranty. I have attached review/install videos...
    view full answer...

  • How to Pick Out Replacement Roof Vent Lid For Fifth Wheel Trailer
  • Most likely we have what you are looking for but you will need to first determine what vent you have on your trailer. The best way to find the correct replacement vent cover for your cargo trailer is to measure the vent. Most standard vents are 14-1/4 by 14-1/4 inches wide, 14 x 14 inches wide or 13 x 14 inches wide. Next if the manufacturer name is on the vent that will help. Finally, you will need to look closely at the hinged portion of the vent. If there is a rolled metal hinge...
    view full answer...

  • Replacement Vent Covers for a 1969 Wilderness Camper Trailer
  • Thanks for the photo. Unfortunately, I can't exactly determine what hinge you have based on this but there are really only a few different types so it should be easy enough to rule the others out. If you take a look at the attached photo, you can see the different types of roof vent hinges. The 14" x 14" opening you have is a standard size so there should not be any issues in regards to this aspect. I have attached an option for each of the hinge types for you below. 3-Point Hinge:...
    view full answer...

  • Can MaxxFan Deluxe Roof Vent # MA00-07500K be Powered From Generator
  • The power draw of the MaxxFan Deluxe Roof Vent # MA00-07500K that you referenced is 5 amps which would easily work with your Inergy Kodiak generator/power supply as long as it has a 12 volt DC power output like the A-iPower 2,000-Watt Portable Inverter Generator # 289-SUA2000I we offer does. So you'd want to check out the generator you have to see if it has a 12 volt output.
    view full answer...

  • Ventline Ventadome Trailer Roof Vent Mounting Hole Measurements
  • The Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - White # V2092SP-28 is the standard vent size. It is not uncommon to have roof braces that are 15 inches apart. This vent has mounting holes that measure 15-1/4 and 15-3/4 inches on center. I've attached a photo of the measurements I took for you. I recommend the Installation Kit # RVIKIT100 for the installation of your roof vent. I've attached a video to assist. We do not carry roof vents of any other size...
    view full answer...

  • Replacement Vent Lid for 1971 Holiday Rambler Galvanized Vent Frame
  • The vent cover for your 1971 Holiday Rambler I recommend is the Replacement Lid for Jensen RV Roof Vent w/ Metal Base - Polypropylene - White # CAM40153 based on your description. If that vent doesn't look like the correct hinge, then I recommend the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent - Translucent White # MA00-335001 which will work with your galvanized vent frame. If you prefer, you can upgrade the entire vent as they are standard sizes. I recommend...
    view full answer...

  • Replacement Lids for Ventline Trailer Roof Vents
  • Thank you for providing the Ventline trailer vent part numbers # BV0554-03 and # BVD0449-A01. Part # BV0554-03 is an Old-Style Domed Smoke-Color Vent Cover with a continuous metal hinge; part # BVD0449-A01 is a Wedge-Shape White Vent Cover with a plastic hinge. These and the other common types of trailer vent hinge designs can be seen in the linked photo. These two types of lid are not compatible with each other; you want to choose the new lid with the same type of hinge as is on...
    view full answer...

  • Is Butyl Tape Needed When Installing MaxFan Roof Vent
  • When installing the MaxxFan Roof Vent # MA00A04301K that you referenced you will want to use butyl tape on the vent edges in addition to the sealant that you will apply around the unit to cover up bolt holes and any other areas that might lead to a leak. I have attached a sample vent installation on a different model vent just so you can get a better idea of the process. We do have the Roof Vent Installation Kit # 344270KITW available that includes a 10.1 oz bottle of sealant, a 60...
    view full answer...

  • Replacement RV AC Shroud Recommendation for RVP Recreational AC Unit with Coleman Mach Shroud
  • Based on the dimensions and picture of your current AC shroud plus the fact it was designed for a Coleman Mach the MaxxAir Shroud part # MA00-325001 would be exactly what you need.
    view full answer...

  • Replacement Vent Cover for Hengs Model 122112 Roof Vent 90110 C1
  • I was able to find a picture of the part number 90110 C1 that you need and found that the exact replacement is the # BV0554-03 that you referenced. If you wanted white instead you'd want # BV0554-01.
    view full answer...

  • Rain Sensor Will Not Allow MaxxFan 4501K to Work Properly
  • Yes, according to my contact at MaxxFan you can simply unplug the connector for the rain sensor from the circuit board in order to bypass it. They were not able to provide me with the location of the connector you will need to remove but if you trace the wires from the sensor to the circuit board that should tell you which one it is. If the fan works once the rain sensor is removed then you know that was the issue but if the fan still does not operate there is an issue with the circuit...
    view full answer...

  • 2004 Starcraft Homestead Fifth Wheel Trailer Roof Weight Rating
  • Virtually any 5th wheel trailer will have a weight capacity for its roof that will be at least enough for a person of average weight to get up there to do things such as repair or replace a roof vent like the MaxxFan Deluxe Roof Vent # MA00-07500K or to adjust the trailer's roof TV antenna. I reviewed an online manual for a 2013 model year of StarCraft trailer (older models' manuals are not offered online) and this indicated that the ladders installed are rated for 350-lbs but the weight...
    view full answer...

  • Dimensions of 42" Hugger Ceiling Fan
  • I reached out to the manufacturer who told me that the height from the top of the 42" Hugger Ceiling Fan for RVs # 324-000037 to the bottom is going to be approximately 16 inches; it is also 42 inches in diameter. As for the wall switch, this ceiling fan does not work with a switch; you will need to use the pull chains to operate the fan as well as the light on the fan. I have added a link to a video review of this fan for you to check out as well.
    view full answer...

  • Replacement Roof Vent Lid with Hinge Screws on Either End
  • I haven't heard of anything factory that has that screw on each end of the hinge. It sounds like somebody simply chose to add the screws. We do not have a replacement for that specific cover if it was an off-brand replacement with that design. My recommendation is to go with one of the standard 4 types of covers whichever best fits your application. It sounds like the Vent Cover for Ventline Old-Style Rounded Dome Trailer Roof Vents - Smoke # BV0554-03 with the bendable hinge may...
    view full answer...

  • Replacement Foam Ring for Ventline Vanair Trailer Roof Vent Part # VP-543SP
  • The foam ring on the Ventline Vanair Trailer Roof Vent part # VP-543SP is a weather seal that is used to help seal the dome on the fan assembly. If you continue to use the fan without the foam ring you would be subjected to leaks which could then short out the motor. If I had to guess I would say that the wax paper was not fully removed from the ring which then caused adhesion problems. Unfortunately, we do not offer the foam ring separately but we do offer the Replacement Plastic Dome...
    view full answer...

  • Does Fan Motor Have to be Manually Turned Off After Closing Lid of Fan-Tastic Roof Vent # FV801200
  • You will have to manually turn the fan of the Fan-Tastic Vent Roof Vent w/ 12V Fan # FV801200 off after closing the lid of the roof vent.
    view full answer...

  • Replacement Vent Cover for Trailer Vent Marked Ventline AS-13 MV101
  • My contact at Ventline tells me that part # BV0554-01 in white or # BV0554-03 in smoke would be the correct replacement lids for your travel trailer. The white is translucent, but the smoked still allows more light in that it.
    view full answer...

  • Locating Replacement Roof Vent Lid for 2000 Jamboree Rallye RV
  • We do have a large selection of replacement lids available for RV roof vents. Most of the lids are designed to fit vents that feature the standard 14-1/4 x 14-1/4 inch size you so will want to first verify that this matches your existing vent. Then it's just a matter of noting the hinge style on your current vent. Your vent should have either a 4-Point, 3-Point, or a plastic/metal continuous hinge. I have attached an image to clarify the different styles. For example the Ventline Vent...
    view full answer...

  • Replacement Roof Vent Lids for 1970s Avion Travel Trailers
  • It sounds like you need replacement lids for the roof vents on your 1979 Avion travel trailers. We offer many replacement vent lids in both metal and plastic and in a variety of colors. Most roof vents in RVs are a standardized 14 x 14 size. These can come with any one of four different types of hinge and you'll want to take note of the hinge style on your trailers before selecting replacements. I reviewed photos of 1970s Avion trailers but I could not confirm the type of vents installed....
    view full answer...

  • Installation of MaxxAir MaxxShade Plus Roller Shade with LED Lights
  • The MaxxAir MaxxShade Plus Roller Shade w/ LEDs for RV Roof Fans - White # MA00-03901 is a new product from the manufacturer that is so new they don't have drawings or instructions completed as of October 2018. Their tech told me that it is a complete unit that installs top and bottom into a standard 14-1/4 inch square RV vent hole with screws to hold the two pieces together. The MaxxShade Plus will have an integrated dome top that will allow the light in when desired and the shade will...
    view full answer...

  • Would MaxxAir Standard RV Roof Vent Cover # MA00-933069 Fit 2015 Forest River Work and Play
  • Yes, the MaxxAir Standard RV and Trailer Roof Vent Cover # MA00-933069 that you referenced will fit the standard roof vent sizes like what your 2015 Forest River Work and Play would have.
    view full answer...

  • Troubleshooting MaxxAir Fan that Doesn't Work but Lid Does
  • It sounds like your MaxxAir MaxxFan Trailer Roof Vent has a powered lift like # MA00-04000K but has a connection issue. It is getting power for the lid to open and close but not for the fan function. I recommend testing your wiring using a circuit tester like # PTW2993 to make sure you are getting power to your fan switch and if so if power is getting to your new motor. If you test the motor with a battery and it works, then you know you have switches or wiring that is in need of repair....
    view full answer...

  • Best Replacement Metal Roof Vent Cover
  • We offer a replacement metal roof vent cover that fits the standard 14 x 14-inch roof vents that are typically found on RVs. Ventline part # BV0534-00 is a plain metal finish flat lid with a continuous type hinge. This is the only metal lid we offer at this time. I linked a photo showing the hinge since this is an important aspect to its fit on the vent. If your vent uses a different style of hinge (all types appear on the other linked photo) you can refer to the linked page for all...
    view full answer...

  • Troubleshooting Fan-Tastic Reversible Roof Vent FV801250 That Squeaks in One Direction
  • My first thought concerning the vent fan being squeaky in only one operating direction is that dust may have found its way into the unit during/after the interior refurbishment process. I am only speculating here, but if for example the fan were operated in outgoing/exhaust mode during the refurb process (when surfaces were being sanded, for example) it could have pulled in material that is causing the noise. The workers might have done this to keep the MH interior as clean as possible...
    view full answer...

  • Cover for Skylight in RV Bathroom
  • We do have some options to check out although we do not carry a shade cover made specifically for a bathroom skylight. The Camco Lights Out Retractable Shade # CAM42913 may work if you have a skylight with dimensions similar to the shade's 19" long x 14-1/8" wide. It will install under the skylight and simply screws in. Another option to check out is the Adco Deluxe Solar Vent Cover # 290-7172 which is 18" x 18" and the Camco Sunshield Shade # CAM45191 which is 16" long x 16" wide....
    view full answer...

  • Troubleshooting No Power to MaxxFan RV Roof Vent MA00-04000K
  • If you have tested the RV's power and ground wires leading to your MaxxFan Trailer Roof Vent # MA00-04000K and you have a full 12V of power reaching the vent's fan motor then there might be damage to the unit's control circuitry or the motor itself. If you apply a voltmeter like # ALL648349 to your power source wiring and you are not detecting a full 12 volts then it could be an issue with a depleted battery. This vent's motor draws 5-amps in use. If you have a spare battery known...
    view full answer...

  • Refrigerator Vent Cover Replacement for Atwood Dometic Refrigerator
  • Only one photo came through, but Dometic bought out that portion of Atwood. We have the Replacement Lid for Dometic Refrigerator Vents - Polar White # VM65528 which may fit your Atwood fridge. The overall dimensions are 27 inches by 10-3/4 inches with the holes being 4-3/8 inches on center and 21-5/8 inches on center. I've attached a photo to assist.
    view full answer...

  • Recommended MaxxFan Deluxe Roof Vent with Fan in White
  • The MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke # MA00-07500K does come in white # MA00-07000K. It will fit in the standard vent cutout of your RV to replace the blade style vent fan you currently have to give you the built in rain shield you mentioned. I've attached a couple videos to further assist. You will also want the TremPro 644 Silicone Sealant - 10.1-Fl-Oz Cartridge - White # 0160297 for your installation.
    view full answer...

  • Is the Valterra Battery Box Cone Vent # A10-3300-05 Plastic or Metal
  • The Valterra Battery Box Cone Vent # A10-3300-05 is plastic. Our video team member goes over this and various dimensions in the attached review video.
    view full answer...

  • What is the Power Source for MaxxFan Deluxe Roof Vent
  • The MaxxFan Deluxe Roof Vent # MA00-05100K requires a 12 volt power source. If there is no wiring where you are looking to install the vent you can run wire like # 12-1-1 to your vehicle battery or other wiring that will allow you a 5 amp draw (which is required for this vent). I have added a link to the installation instructions of this vent for you to check out as well.
    view full answer...

  • Installation of MaxxAir MaxxFan Trailer Roof Vent
  • While we would not have any way to know for sure it is unlikely there is going to be wiring run. In order to install the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K you would need to use Primary Wire - 16 Gauge # DW02359-1 to run wire to a 12V power source. This vent is designed to fit standard RV roof openings of 14” x 14” and a minimum roof thickness of 1-1/8” to a maximum of 6-1/2”; it will also require the use of Sealant # 0160297 to ensure a tight bond between the flange...
    view full answer...

  • What Size Fuse is Used for the Fan-Tastic Vent Roof Vent # FV801250
  • The fuse for the Fan-Tastic Vent Roof Vent # FV801250 is a 4 amp fuse. If you were wanting to use an in-line fuse holder then the part # C58470-1 can handle up to 10 amps so it would work well with a 4 amp fuse.
    view full answer...

  • Replacement Ceiling Fan for 5th Wheel Trailer
  • We do not offer a blade replacement kit but there are a number of hugger-style ceiling fans that you can choose from to replace your current fan. You did reference your current fan's blades being 20 inches so I am guessing that you have a 42 inch hugger-style ceiling fan, with the 42 inches being the fan's total diameter (which means if you measure from the end of one blade to the end of the blade across from it you will get 42 inches). If that is the measurement you get then you...
    view full answer...

  • Replacement Hardware and Brackets for RV Ceiling Fan
  • Does your 2011 Montana High Country 5th Wheel have the Airrforce 42" Hugger Style RV Ceiling Fan with Light Kit # 277-000081? If so, we have both brackets and hardware available for that fan. If you need the brackets they are Replacement Brushed Chrome Brackets # 277-000399; there is also the Replacement Hardware Pack # 277-000408 which includes 12 fan blade screws and a pull chain. All of the prices can be seen on the linked product pages of the respective items or on this page...
    view full answer...

  • How to Remove Bug Screen on Maxxfan 4-Speed Roof Vent
  • To gain access to your MaxxFan Roof Vent # MA00A04301K you will need to simply remove the screen by rotating each of the clips 1/2 turn as per the instructions (which I have linked for you). When doing this please be sure that you not only turn off the fan but also have the 12 volt power disconnected.
    view full answer...

  • Replacement Exterior Wall Vent for RV Range
  • While we do not have any type of parts lists or database for every year, make and model of trailer because trailer manufacturers do not keep those type of records I can go over each of our exterior wall vents for you to compare and see what might work for you. Each of the exterior wall vents we carry for range hoods will fit 10-1/2" wide x 3-3/4" tall rough openings so please be sure that is the size of the opening you have in your trailer. These exterior wall vents also require 10 screws...
    view full answer...

  • Replacement Roof Vent Lid With 3-Point Hinge
  • Thank you for the photo; from that it looks like you have a 4-point hinge (like in the accompanying photo I added) and we do have a cover, the Vent Cover for Jensen Trailer Roof Vents - White # 61628 which may work for you. If you have an older vent there is also the Replacement Lid for Jensen RV Roof Vent w/ Pin-Style Hinge # CAM40147 which fits 14" x 14" Jensen vents with pin-style hinge (pre-1994). Another option is the MaxxAir UniMaxx Universal Replacement Lid # MA00-335001 (White)...
    view full answer...

  • Does Ventline Metal Roof Vent # BV0534-00 Fit Ventline Roof Vent # V2094SP-28
  • Yes, the metal vent lid cover part # BV0534-00 is designed to fit the Ventadome style of Ventline roof vents like the part # V2094SP-28 you mentioned.
    view full answer...

  • Replacement Roof Vent Lid Recommendation for Older Style Ventline Roof Vent
  • You mentioned having the "old style of Ventline hinge" which is what the # BV0554-01 has. This is a rolled metal hinge like what you see in the attached picture. If this matches what you have this would be the correct replacement. The measurement you mentioned would match too.
    view full answer...

  • Will the Fan-Tastic Vent Roof Vent Fan Work on an AC Outlet
  • I do have an option for you to hook up the Fan-Tastic Vent Roof Vent part # FV801250 to a 120 volt AC outlet using the plug part # FV8607-09 and converter part # FV1101-09 but I don't have any way for you to switch back and forth between 120 volt AC and 12 volt DC power. You would need to either pick one or the other. I recommend using the trailer battery as that is what the fan is designed to run on.
    view full answer...

  • Can the MaxxFan Trailer Roof Vent # MA00-04000K be Left Open Without Rain Getting Inside
  • The only way to operate the MaxxAir MaxxFan Trailer Roof Vent # MA00-04000K without rain getting inside is to also install the MaxxAir II Rain Cover # MA00-933072. If you are wanting a single-piece unit that includes a rain cover and utilizes a thermostat and a manual lift then the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K for Smoke or # MA00-05100K for White is exactly what you are looking for. All of these roof vents come with mounting hardware but you will also need some...
    view full answer...

  • Replacement Round Bug Screen for MaxxAir Roof Vent
  • We do have the replacement round screen for your MaxxAir roof vent, like the MaxxFan # MA00-04000K. This is listed as part # MA05-30925 on our site.
    view full answer...

  • Vent Fan for Trailer with Reverse, Dual Lift Arms, 900+ CFM Rating, and Integrated Cover
  • I do have some very good options for you but in order to obtain a vent assembly with reversible fan, dual lift arms, >900 cfm motor, and built in cover you will have to settle with some additional features such as a thermostat and remote etc. Unfortunately, these vents cannot be custom ordered and they don't offer an assembly with just the features you want. The most cost effective vent we offer with all the features you described is the MaxxFan Plus Roof Vent w/ 12V Fan part # MA00-04500K....
    view full answer...

  • Will the Ceiling Garnish Part # VA0445-37 Fit the Ventline Ventadome Vent Part # V2110SP-24
  • Yes, the Ceiling Garnish for Ventline Roof Vent part # VA0445-37 will fit the Ventline Ventadome Trailer Roof Vent part # V2110SP-24. Please keep in mind that the garnishes can be trimmed for an exact fit. The metal lid will hold up much better to harsh uv rays than the standard polyethylene lids.
    view full answer...

  • Replacement Screen for Ventline Northern Breeze Roof Vent
  • I spoke with my contact at Ventline and they informed me that the Ventline Northern Breeze Screen part BVDO231-00 is obsolete and no longer available. I understand if you would like to keep looking elsewhere however, if one cannot be found then your only option is to replace the entire vent unfortunately. If you choose to take this route I recommend taking a look at one of the following. Fan-Tastic Vent part # FV800900 (Manual Lift, No Fan) Fan-Tastic Vent part # FV801250 (Manual Lift,...
    view full answer...

  • Can Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-28 Install On Roof Thickness of 2-13/16
  • Looks like you have a roof thickness of right at 2-3/16 inches like you mentioned which isn't a problem at all to install the Ventline Ventadome Trailer Roof Vent # V2094SP-28 that you referenced. This comes with a garnish that is 2-1/8 inches tall so you'd only really need to lightly trim it shorter for it to match perfectly to your roof thickness.
    view full answer...

  • Replacement Lid Needed for 2004 Everest Roof Vent LF8000T
  • From what I could find it looks like your LF8000T is a Fan-Tastic Vent model 8000. If this is the case then yes, the Replacement Dome # FVK1020-19 is the correct cover for your application. I have attached a review video of this lid that you can reference. If you don't have the model 8000 or you are unsure just send me a picture of the top and bottom of the vent and I can help you determine the correct replacement.
    view full answer...

  • Can I Use a Lighting Fixture Circuit to Power a MaxxFan 4000
  • What is the maximum amperage of the circuit for the lighting fixture you intend to use and what is the total amperage draw for the lights you have ran to that circuit? I would need to know this information in order determine if it has enough power for the MaxxFan 4000. The MaxxFan 4000 draws 5 amps so if the total amp draw for all of the lights you have on this circuit plus the vent fan does not exceed the maximum amperage of the circuit for the lighting fixture then you will be fine. The...
    view full answer...

  • Solar Powered Exhaust Fan Recommendation for Enclosed Trailer
  • If the MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat # MA00-05100K were to totally lose its power source it would lose all of its presets like with a car stereo. When in use this will draw up to 5 amps so it would be pretty taxing on a solar panel without a battery backup. We do have the Ultra-Fab Solar-Powered Plumbing Vent for Motor Homes # UF53-945001 which is a solar panel power exhaust fan that's totally self-contained. You'd just need to mount it and it would work on it's own.
    view full answer...

  • How Does Valterra Adjustable A/C Ceiling Register # A10-3359VP Remove Once Installed
  • There are four clips that hold the outer vent portion of the Valterra Adjustable A/C Ceiling Register # A10-3359VP to the collar that attaches with screws. To remove the outer section once installed you'd need to reach your finder into the vent opening and pull on the latches so that they free up. I pointed out where they are in the picture I attached.
    view full answer...

  • Roof Vent Needed with 12V Fan That Sits Under 5" Tall
  • The Ventline Ventadome Trailer Roof Vent # V2094SP-34 that you referenced actually sits only 4-1/2" above the roof when it is closed so it will fit in your garage! It comes with a 12V fan that is powered by DC. Most of our vents fit this description though so you are in luck! If you are looking for a vent that can stay open and still fall under your 5" height restriction then you will need the Ventline Vanair Trailer Roof Vent # VP-543SP. This is a round vent with a diameter of 6-1/4"...
    view full answer...

  • Replacement Roof Vent Lid Needed for a 2015 Freedom Trailer
  • Although I don't know what exact vent you have on your 2015 Freedom trailer, I can help you figure out which replacement vent lid is the correct one for your application. Replacement vent lids are actually pretty universal. The only info we really need is what kind of hinge your vent uses. We have a 3-point hinge, part # 69284, a 4-point hinge, part # 61628, a continuous hinge, part # BV0554-03, and a universal hinge, part # MA00-335001. If you have get a picture of your hinge from...
    view full answer...

  • How to Pick Out Replacement Roof Vent Lid for 1989 Avalon Fleetwood Travel Trailer
  • Most likely we have what you are looking for but you will need to first determine what vent you have on your trailer. The best way to find the correct replacement vent cover for your cargo trailer is to measure the vent. Most standard vents are 14-1/4 by 14-1/4 inches wide, 14 x 14 inches wide or 13 x 14 inches wide. Next if the manufacturer name is on the vent that will help. Finally, you will need to look closely at the hinged portion of the vent. If there is a rolled metal hinge...
    view full answer...

  • How to Pick Out Replacement Vent Lid for 2009 Palamino Puma
  • Sounds like what you are really looking for is a replacement lid for the vent on your 2009 Palamino Puma. The easiest way to do this is to use the hinge style that's on the roof vent as that's the most identifiable way. If there is a rolled metal hinge attached to the vent cover like on the Ventline Replacement Smoke Dome Assembly, part # BV0554-03. Then that is most likely the correct vent for your trailer as long as the measurement matches. There are also vent covers with plastic...
    view full answer...

  • Best Roof Vent Cover for a MaxxAir Vent Fan 4500 Model
  • The MaxxAir II Trailer Roof Vent Cover and MaxxAir FanMate Vent Cover will both fit your MaxxAir Vent Fan 4500 Model. If you have the Plus then there will be standoffs on the top of the vent that will be used to snap the cover in place but if you do not have these standoffs then it comes with the other hardware you need. I have attached the compatible options for you below. MaxxAir II Trailer Roof Vent Cover (White) - part # MA00-933072 MaxxAir II Trailer Roof Vent Cover (Black) -...
    view full answer...

  • How to Set a MaxxAir Vent to Blow Opposite Direction
  • If the vent fan you have now is reversible then there should be a button on the assembly next to the other controls. However, if the fan is not reversible then all you need to do is reverse the wires on the motor (not the circuit board) and that will then allow the fan to blow air into the van.
    view full answer...

  • Low Profile Vent with Flush Knob for Collapsible Roof
  • I was not able to reference the FanTastic Vent part 810192 but I believe I have exactly what you need. The Ventline Ventadome Trailer Roof Vent part # V2092SP-28 is designed for a 14-1/4" wide x 14-1/4" long openings which is likely what you have and the open/close knob is recessed inside the vent assembly. In order to install this vent I recommend using the Installation Kit part # RVIKIT100. I have attached an install and review video for you as well.
    view full answer...

  • Vent Cover Needed for MaxxAir MaxxFan Vent on a 2018 Forest River R-Pod
  • The rain covers that are direct fits your MaxxAir MaxxFan # MA00A04401K are parts # MA00-955003 for Smoke and # MA00-955001 for White. These come with clips that allow you to easily secure or remove the cover from the MaxxFan. If instead you are talking about a replacement lid then you would be wanting part # MA10A40009K.
    view full answer...

  • Troubleshooting Loss of FM Signal After Removing Satellite Jack
  • It's very possible the FM antenna was ran to the same area as where you satellite antenna jack was. Most likely when pulling wires around you dislodged the FM antenna from the back of the stereo. I'd check there to see if you can get it reattached. It wouldn't be standard for an FM antenna to have a switch that activates it. There are some powered FM antennas that would have a switch, but that is not common in your application.
    view full answer...

  • Replacement Roof Vent for 1976 Silver Streak 2600 Trailer
  • Thanks for the photo. It appears you have just a standard manual lift vent, so my recommendation is to use the Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - White # V2092SP-28 or smoke colored cover # V2092SP-29. These vents use the standard trailer rough opening you have and will be an easy replacement as well as basic upgrade. Either option will fit in the same rough opening as your current vent and I recommend using the Installation Kit - for Ventline Ventadome...
    view full answer...

  • Ventline Vanair Trailer Roof Vent Dimensions and Weight
  • The Ventline Vanair Trailer Roof Vent w/ 12V Fan - 6-1/4" Diameter - Smoke # VP-543SP is very light weighing just under 2 pounds each. I recommend using installation kit # RVIKIT100 for mounting this vent. I've attached some videos as well as some dimensions of this unit to assist.
    view full answer...

  • Does MaxXAir II Vent Cover Use the Same Mounting Holes as Original MaxxAir Cover
  • The MaxxAir II RV and Enclosed Trailer Roof Vent Cover # MA00-933075 can be used to replace the original MaxxAir cover and it will use the same mounting holes. You should not have to drill any new holes unless the original holes were not used for some reason. All of the necessary hardware is included for installation though if you wanted you could reuse the old hardware if it is in good shape. This is pretty much just a case of removing the old one and putting the new on in its...
    view full answer...

  • Replacement Dome for Fan-Tastic Vent Model 6000A or 6000BTA
  • By "slider track" I believe you are referencing the hinge; if you take a look at the accompanying photo you should be able to see what I am talking about. That should be what your Fan-Tastic vent has and since your model 6000A/6000BTA will measure the standard 14" x 14" there are two replacement domes available, the Replacement Dome for Fan-Tastic Vent RV Roof Vents - Tinted # FVK1020-19 or White # FVK1020-81.
    view full answer...

  • Recommended Trailer Vent with Integrated Screen for 14x14 Inch Vent
  • Unfortunately we don't have the replacement screen for your assembly based on the photo. I recommend using the Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - White # V2092SP-28 as a complete replacement as it is a very popular brand with the replacement screens if you should need it in the future. These vents are all a standard size that is referred to as 14 by 14 even though the rough opening is a 1/4 inch larger in both directions. If you prefer the smoke...
    view full answer...

  • Will the MaxxAir II Cover # MA00-933075 Fit a Fan-Tastic Fan
  • The MaxxAir II Cover # MA00-933075 is a universal fit so it will fit a 14" x 14" Fan-Tastic Fan. The clamps are installed on the roof so it isn't brand-specific.
    view full answer...

  • Is Hardware Included with MaxxAir II RV Trailer Roof Vent Cover # MA00-933075
  • Yes, the MaxxAir II RV Trailer Roof Vent Cover # MA00-933075 referenced in your question comes with all the necessary hardware for installation. This includes the 8 self-tapping screws and hinged mounting brackets. I have attached a short video demonstration that you can also check out.
    view full answer...

  • No Lights on Remote for a Fan-Tastic Vent Model 6600R
  • The problem you described sounds like an issue on the remote's circuit board. If the fuse was blown then the fan would not work at all as you mentioned. Unfortunately, the replacement remote for the Fan-Tastic Vent Model 6600R is no longer available as the vent has since become obsolete. Therefore, the only option you have unless you are able to find someone who is experienced enough with circuit boards to repair the remote would be to replace the unit for which we have the Fan-Tastic Vent...
    view full answer...

  • Will the MaxxAir II Vent Cover # MA00-933075 Fit the MaxxFan Plus Roof Vent # MA00-04500K
  • Yes, the MaxxAir II RV and Enclosed Trailer Roof Vent Cover # MA00-933075 will fit the MaxxFan Plus Roof Vent # MA00-04500K. The reason that the vent cover is so much larger is that it is more of a universal style. If you would like a more custom fit then you need the MaxxAir FanMate Rain Cover # MA00-955002.
    view full answer...