fall hauling headquarters
Filter Results

Filter Questions and Answers:

reset filter
Gooseneck
Gooseneck
 

Expert Answers about Gooseneck


  • Installing Curt Folding Gooseneck Hitch in 1998 GMC Extended Cab K1500
  • The Curt Overbed, Folding Ball Gooseneck Trailer Hitch with Installation Kit # C61503-52 is the correct fit for your 1998 GMC K1500. This kit will put the rear cross rail 3-6 inches in front of the rear axle but the hitch ball platform location will be based on those rails. The attached installation details will give you the only measurements needed. If you have the plate but not the custom rails, you will need # C61503 for a custom fit installation. The Folding Ball Gooseneck Hitch...
    view full answer...

  • Which Draw Tite Hide-A-Goose Gooseneck Hitch Fits 2017 Ford F-350
  • Draw Tite does make a Hide-A-Goose gooseneck hitch that fits your 2017 Ford F-350. For that you'd want the part # 9468-94 which comes with the center section and the rail kit. Individually these part numbers are # 4494 and # 9468.
    view full answer...

  • Where to Drill 4 inch Hole in Truck Bed of 2013 Ram 1500 for B and W Turnoverball Hitch
  • Take a tape measure and hook the end of it over the end of the truck bed and 45-3/4 inches forward of that point will be where to drill the 4 inch hole in the bed of the truck. You will need to center from left to right as well. I confirmed that is where the hole goes when installing the B and W Turnoverball Gooseneck hitch part # BWGNRK1117.
    view full answer...

  • Is Curt Gooseneck Ball Tall Enough for Bed Rail Clearance Towing a Goose Box with a 2019 Ford F-350
  • Since the newer pickups have bed side rails that are a little higher than previous models years I wouldn't be able to say with 100% certainty that the Curt Ball # C60692 would provide enough clearance for your 2019 Ford F-350 Super Duty, but I do have some measurements that you can use to find out. From the base of the Curt hitch ball to the top of the ball measures 5-1/8". If you back your F-350 up to your trailer with the Goose Box you should be able to take some measurements to see...
    view full answer...

  • Compatibility of Curt Underbed Gooseneck Hitch with Andersen Ultimate 5th Wheel Trailer Hitch
  • While we do not currently carry the gooseneck mount version of the Andersen Ultimate Connection 5th Wheel Trailer Hitch, it is indeed compatible with the Curt Underbed Gooseneck Trailer Hitch # C60614 that you referenced. You will not have any issues in terms of fit or function with these two components. I did notice that you listed the 2017 Ram 3500 as your truck. If this is correct then the Curt Gooseneck Hitch # C60614 is actually not confirmed to fit. You will instead need the Curt...
    view full answer...

  • Recommended Air Bag Kit for a 2018 Ford F-350 Dually with B&W Gooseneck Hitch Installed
  • Since the B&W Gooseneck Hitch # BWGNRK1116 on your 2018 Ford F-350 installs on the sides of your frame the Air Lift LoadLifter 5000 Ultimate Air Helper Springs # AL88391 is what I recommend going with. These install between your axle and the bottom of your frame so it is compatible with your B&W hitch and will not prohibit the use of the lever for the hitch ball. This kit is rated for up to 5,000 lbs and features internal jounce bumpers for extra support. The air compressor kit that...
    view full answer...

  • Gooseneck Hitch Recommendation for 1997 Ford F-250
  • For your 1997 Ford F-250 we have great gooseneck hitch options that will fit and work well, but we do not have any options from Draw Tite. Instead I would recommend the B and W Turnoverball hitch part # BWGNRK1110 which is a confirmed fit and would be a really great option. The B&W towing products are considered by most people to be the best and most reliable options around so we recommend them highly. Also if you ever wanted to tow a fifth wheel hitch you can easily use a Companion Hitch...
    view full answer...

  • Recommended Clearance Between Bumper and 5th Wheel Trailer
  • The recommended clearance between the rear bumper on your 2018 Chevrolet Silverado 2500 and the body on your 2017 Grand Design Reflection is about 16" - 24" so it sound like you are good. There are also a few other clearance measurements you need to consider which I have attached a photo of for you. If you need more vertical clearance then you may want to consider using the B&W Ball and Safety Chain Kit part # BWGNXA2061 as it has a high rise gooseneck hitch ball but they don't make...
    view full answer...

  • What Are Mounting Puck Dimensions of Demco Hijacker UMS Series Gooseneck Trailer Hitch
  • I appreciate you getting me the picture of your dimensions but it's not totally clear exactly what you have dimensionall. Instead check out the picture I attached that shows the dimensions of the mounts on the Demco # DM5988 that you referenced. What is the year/make/model of the truck? It looks like a factory rail kit from Ford, GM, or Dodge but I'd need to know what you have to be sure.
    view full answer...

  • Recommended Replacement Gooseneck Hitch for Valley Stow-A-Ball Style Hitch in 2005 Chevy 2500
  • It looks like you have an old Valley Stow-A-Ball Gooseneck but it also looks like it is incomplete. Valley is no longer in business so that ball is no longer available. I've attached a photo of that style ball to help. There is not a gooseneck hitch that I'm aware of still on the market that doesn't use a locking pin, so I definitely recommend updating your system for safety. My recommendation is to replace the unit with the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom...
    view full answer...

  • Installation of Curt Gooseneck Hitch in 2012 Ford Super Duty Truck Using Center Locator
  • The Curt Double Lock, Flip and Store Underbed Gooseneck Hitch w/ Installation Kit - 30,000 lbs # C60720 does not come with the hole locator you are referring to. That orange locator comes only with the Curt EZr Double Lock Underbed Gooseneck Trailer Hitch with Installation Kit - 30,000 lbs # C60683. It is a really nice and easy way to ensure the gooseneck hole is in the correct location without all the measurements. With either of these gooseneck options you may also be interested...
    view full answer...

  • B&W Gooseneck Hitch Hole Location on Bed of 2016 Chevy Silverado 2500
  • If you check out the attached picture of the instructions for the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1016 you can see that the center of the 4" hole will need to be 44-3/4" from the back of your 2016 Chevy Silverado 2500. This is only the bed and doesn't include the tailgate. The 4" Offset Ball # BWGNXA4085 is compatible with this gooseneck hitch. You may also be interested in adding a 7-Way connector to your bed with part # 50-97-410 to help make connecting...
    view full answer...

  • Does Bed on 2018 Ford F-350 Need to be Removed to Install B&W Gooseneck Hitch
  • You actually don't have to remove the bed to install the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1116 on your 2018 Ford F-350 Super Duty. The hitch comes in pieces that you lift into place one at a time from underneath the bed. Attached is an installation video of this hitch on a 2017 Ford F-350 for you to reference.
    view full answer...

  • Best Ram 3500 Truck Options to Pick for Gooseneck Trailer Towing
  • The best options for towing a gooseneck trailer for a 2018 Ram 3500 will be long bed, diesel engine, dually. The cab style will be determined by how many people you will be traveling with most likely. You should note that the wider the doors, the longer the vehicle. You'd end up with a pretty long and wide truck if you did a quad cab, long bed, dually. Long bed allows you to have turning clearance in sharp turns, diesel engine gives you the torque and longevity for heavy towing, and...
    view full answer...

  • How Much Play to be Expected with Curt OEM Rail Kit Gooseneck Ball # C60692
  • How much movement are you seeing? I spoke with my contact at Curt and he said 1/16 inch of play between the ball and the hitch would be considered normal.
    view full answer...

  • Best Gooseneck Trailer Hitch Ball for 2019 Ford F-350 Super Duty With Factory Gooseneck Package
  • The best gooseneck hitch ball kit for your 2019 Ford F-350 Super Duty with the factory gooseneck is the Reese Elite Series Pop-In Ball Kit # RP30137 because its hitch ball is simple to put in or remove and it has safety chain loops which have an inside width of 1-1/8" so if your safety chains have larger hooks these hoops will be able to accommodate them.
    view full answer...

  • B&W Gooseneck Hitch for a 2019 Chevy Silverado 2500
  • The correct B&W Gooseneck Hitch for your 2019 Chevrolet Silverado 2500 is the part # BWGNRK1016 this is compatible with both a 6-1/2' bed and an 8' bed as long as you don't have the OEM Prep Package as you stated. I also recommend installing a 7-Way like part # 50-97-410 on your Chevy so that it is easier to connect and disconnect the 7-Way from your gooseneck trailer. One of the reasons why the B&W gooseneck hitch is so accepted is due to the fact that B&W came out with their own...
    view full answer...

  • B&W Turnoverball Gooseneck Hitch for 2019 Ford F-350 Super Duty Four-Wheel Drive Dually
  • For your 2019 Ford F-350 Super Duty four-wheel drive dually you need the B&W Turnoverball Gooseneck Hitch # BWGNRK1117, which will fit either the 6-3/4' or 8' bed of your F-350. Since you have a dually with an expanded wheel well I highly recommend using the Extended Latch Pin Handle for B&W Turnoverball Gooseneck Trailer Hitch # BWGNXA1800. This is a 17" latch pin which is going to make it much easier to reach on your F-350 dually than the standard latch pin handle.
    view full answer...

  • How to Determine if Curt Gooseneck Adapter # 16055 Will Fit RBW Base Rails
  • The Curt Above-Bed Gooseneck Trailer Hitch # 16055 will mount to all "standard" 5th wheel base rails. I am not sure what the measurements are for RBW rails but I have attached a picture that shows the dimensions of "standard" bed rails as well as dimensions of where the tabs are for the Curt unit.
    view full answer...

  • Can Short Bed Trucks Tow Gooseneck Trailers
  • The one really big downside to gooseneck towing is that there isn't a great solution for short bed truck clearance unlike fifth wheel towing. With fifth wheel hitches you can use a slider hitch and have the clearance issue handled. With gooseneck towing there isn't really anything you can do. The only way it's possible is if the nose of the gooseneck trailer is tapered to help with the turning clearance. The Spyder part # 16085 does fit industry standard fifth wheel rails like you have...
    view full answer...

  • Recommended Gooseneck Trailer Hitch for 2012 Ram 1500 Big Horn
  • If you have the 6-1/2 foot bed with the Quad Cab or the 5-1/2 foot bed with the Crew Cab, I recommend the same hitch. It is the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs # BWGNRK1309. This is a confirmed fit for your truck and if you have the 6-1/2 foot bed without RamBox it also offers a 5th wheel slider compatibility for a clean bed. If you want a good hitch but a more economical option, I recommend the Curt # C60730 which is only a...
    view full answer...

  • Troubleshooting Squeaking B and W Turnoverball Gooseneck Hitch After Greasing it
  • Most likely the issue is not the ball of your B and W Turnoverball Gooseneck Hitch part # BWGNRK1111 and it's the coupler on your trailer. You can inspect the ball though and make sure it's not damaged in any way. For a replacement we have the part # BWGNXA2000. Depending on what coupler your trailer has it could have an inner tube on it that could be replaced. I'd have to know what coupler you have or see a picture to verify if we could help with that.
    view full answer...

  • Best 5th Wheel and Gooseneck Setup for a 2019 Ford F-250 with 6-3/4 Foot Bed
  • We offer everything you need to tow a 5th wheel and or gooseneck trailer with your 2019 Ford F-250. The factory does offer a prep package but if you are looking to save money then aftermarket would be the way to go. The main advantage you have with factory installed components is their warranty but there are pros and cons to each options as well. The best setup we have for your F-250 which will allow you to tow both gooseneck and 5th wheels trailers is to use the B&W Turnoverball Underbed...
    view full answer...

  • Tips for Getting Reese Elite Series Pop-In Ball Kit for Ford Rail Kit to Fit Truck
  • Are the balls on the side of the ball that comes with the part # RP30137 fully retracted when you have the release mechanism on top of the ball pulled out? Is there anything in the ball hole that's obstructing the ball from fitting?
    view full answer...

  • Installing Draw-Tite Gooseneck Hitch on 2018 Toyota Tundra with Firestone Air Springs Installed
  • The Draw-Tite Hide-A-Goose Underbed Gooseneck Trailer Hitch # 9465-36 referenced in your question is confirmed to fit your 2018 Toyota Tundra but it will mount to the same location inside and under the frame where your existing brackets for the Firestone Ride-Rite Air Helper Springs # F2445 are mounted. Because of this the two systems are not compatible with each other. In order to install this gooseneck hitch on your truck you will need to remove the Firestone Air Helper Springs. For...
    view full answer...

  • Is there an Andersen 5th Wheel Hitch that Fits a B&W Turnover Ball Gooseneck Hitch
  • There is an Andersen Ultimate 5th Wheel Connection that clamps onto a standard 2-5/16 inch gooseneck ball including B&W as well as other brands. We do not currently offer that hitch but we do have something that is better. Take a look at the Demco Recon # DM8550045. This hitch actually has a 5th wheel hitch head on it so you don't have to attach an adapter to the trailer king pin like you would with the Andersen hitch. The Recon will be a safer and more stable connection. Plus the Recon...
    view full answer...

  • Will B&W Gooseneck Trailer Hitch Fit a 2018 Ram 3500 with Factory Air Leveling Suspension
  • Yes, you can install B&W Turnover Ball gooseneck trailer hitch # BWGNRK1314 on your 2018 Ram 3500 with the factory air leveling system. Your truck already has the structure under the bed to add the gooseneck hitch which means this installation does not require frame brackets (not to be confused with the factory prep package which is a little different). It is normally the frame brackets that can interfere with things like air suspension. But in this case it is not an issue! I have linked...
    view full answer...

  • How Will Taller Gooseneck Ball Affect Trailer Height
  • The B&W ball, part # BWGNXA2062, will sit higher off the truck bed by about 1-1/4 inches when compared to the Curt # C60618 and the Reese # RP30140 hitch balls. If the B&W's height helps your trailer sit more level then it may improve your set up but that slight difference isn't going to make much impact very often. Although, making the trailer as level as possible is always better.
    view full answer...

  • Can B&W Gooseneck Hitch from 2015 Chevy Silverado 2500 Convert to 2018 Model
  • From 2015 to 2016 there was a big enough change to the Chevy Silverado 2500 models that B and W had to come out with an all new hitch fit for the truck. That means that for your 2018 model you'd need the # BWGNRK1016 for an all new kit or if you wanted just the rails to move the center section to the new truck you'd want the part # BWGNRM1016.
    view full answer...

  • B&W Gooseneck Mounting Brackets Needed for a 1994 Chevy K2500
  • If you have a 6-1/2' bed on your 1994 Chevy K2500 then the B&W Gooseneck Hitch that fits is part # BWGNRK1050. If you already have the hitch part # BWGNRC950 then you simply need the bracket kit # BWGNRM1050. If you have the 8' bed on your K2500 then the B&W Gooseneck hitch that fits is part # BWGNRK1000 with the hitch part being # BWGNRC800 and the brackets being # BWGNRM1000. The center section is specific to the vehicle so if you aren't sure what you have or if it is the incorrect...
    view full answer...

  • Are Air Bags Compatible with the B&W Gooseneck Hitch on a 2013 Ford F-150
  • I do have a suspension enhancement solution for your 2013 Ford F-150 but since you have the B&W Gooseneck Hitch # BWGNRK1104 installed the only Air Lift kit that will work is part # AL57200 and that is if you have a 4WD. If you have a 2WD I recommend using SuperSprings SumoSprings. These replace the factory bump stops on your F-150 and offer more stability as your payload (or pin weight) increases. One of the best things about this option is that there is absolutely no maintenance that...
    view full answer...

  • Recommended Gooseneck Hitch for a 2018 Ram 1500 with a 6'4" Bed
  • I recommend going with the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1309 for your 2018 Ram 1500. This is a great gooseneck hitch that is made in the USA and has received numerous positive reviews from our customers. It has a weight capacity of 30,000 lbs but you will be limited by the weight rating of your pickup. One of the best features of this gooseneck hitch is that B&W made the Companion # BWRVK3400 sliding 5th wheel hitch that fits directly into the receiver. This...
    view full answer...

  • Troubleshooting Latch Pin on B&W Gooseneck Hitch That Will Pull Out But Won't Rotate
  • I spoke with my contact at B&W and he said that your case is rare but they have seen this happen before. When you are able to pull the handle on your gooseneck hitch back but you can't rotate it what is happening is that the there is a spring on the latch pin that is prohibiting you from pulling that pin out far enough. My contact said that they tell customers to cut a coil or 2 from that spring and you should be able to rotate the handle. Since you are not able to rotate the handle...
    view full answer...

  • Will 5th Wheel Pin Weight be Too Much for a Ford Pickup with Aluminum Bed
  • Even though Ford seemed to get a lot of backlash for moving to an aluminum bed (not frame), some of the other pickup manufacturers are actually looking at releasing their upcoming lines with aluminum beds (as of August 2018). When it comes to 5th wheel or even gooseneck towing, the brackets for the system are installed on the steel frame of the pickup. This means that you won't be relying on the "weaker" (as some have put it) aluminum bed to carry your pin weight. If you lookup the...
    view full answer...

  • Recommended Gooseneck Hitch Ball and Safety Chains for a 2015 Ram 3500
  • It sounds like you are looking for a gooseneck hitch ball and safety chain loops to work with the factory prep package you have on your 2015 Ram 3500. If that is the case then you can use the Curt Ball and Safety Chain Loops Kit part # C60618 that you came from. This kit includes a 2-5/16" hitch ball, two safety chain loops, a hitch cover, and a carrying case all of which will fit your Ram 3500. I have attached an install video for you as well.
    view full answer...

  • Best Gooseneck Hitch for a 2012 Ram 2500 Mega Cab Diesel
  • We have a few gooseneck trailer hitches that will fit your 2012 Ram 2500 Mega Cab Diesel which I have attached a list of for you. The best option we have is the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1313. The Turnoverball is one of the best trailer hitches on the market today. It has a 30,000 towing capacity with a custom fit design that minimizes drilling into the frame. The best thing about the Turnoverball is that you can easily tow a 5th wheel trailer if...
    view full answer...

  • Gooseneck Ball and Puck Trim Kit for Ford Factory Fifth Wheel Rail Kit
  • For a gooseneck ball to fit the factory rail kit of your 2014 Ford F-350 you'd want the Reese Elite kit part # RP30137 which would fit right into the pucks of your truck. We have the replacement puck trim kit part # RP58458 which will give you the trim rings you are needing.
    view full answer...

  • Replacement Hardware List for B and W Gooseneck Hitch part # BWGNRK1313
  • We don't carry just a hardware kit for the bolts of a B and W gooseneck hitch part # BWGNRK1313. Your best option would be to take the following list of bolts to your local hardware store so that you can piece together everything you'd need. Also this list is in the attached install instructions page link.
    view full answer...

  • Center Hole Location for Installing Draw-Tite Gooseneck Hitch # 9460-48 on 2002 Ford F-350
  • The Draw-Tite Hide-A-Goose Underbed Gooseneck Hitch # 9460-49 referenced in your question is confirmed to fit your 2002 Ford F-350 with the long bed. For your long bed truck (and the short bed models as well) the center hole will indeed be cut 46-3/16 inches from the rear of the bed and centered between the wheel wells. I have attached the complete installation instructions that you can also reference.
    view full answer...

  • Will the Hi-Rise # 9480 Mount to a Draw-Tite # 8339 Gooseneck Hitch on a 2008 Ford F-350
  • Since you have the Fold-Down Gooseneck Trailer Hitch # 8339-4448 there actually isn't a way for the Hi-Rise # 9480 to secure to the gooseneck hitch since it sits down in the coupler section of the gooseneck hitch. To use the Hi-Rise you will need to swap out the top part of your gooseneck hitch with part # 9460 which allows you to remove the hitch ball. If you went this route then you also need replacement mounting hardware # 58320 since the hardware is only meant to be torqued once. We...
    view full answer...

  • Estimated Installation Time for B&W Turnoverball Gooseneck Hitch on 2007 Chevy Silverado
  • I spoke with my contact at B&W regarding the Turnoverball Underbed Gooseneck Hitch # BWGNRK1067 for your 2007 Chevy Silverado. He said that a driveway DIYer like yourself can expect an installation time of about 2-3 hours. All of the needed hardware and frame brackets are included with this kit. Because the brackets are custom-fit for your truck, you won't need to drill into the frame to install them. I have attached an installation video on the 2008 Silverado that you can use for reference,...
    view full answer...

  • Will the B&W Turnoverball Fit a Lowered 2018 Ford F-150
  • The gooseneck hitch I recommend for your 2018 Ford F-150 is the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1115. This hitch has a 30,000 lb towing capacity and is considered to be one of the best on the market. We have not yet had a chance to install this hitch on a lowered F-150 but I spoke with my contact at B&W and they informed me that as the hitch is placed forward of the rear axle, you should be okay with the lowering kit but there are several others factors at...
    view full answer...

  • Gooseneck Hitch Fabrication Parts for 2018 Ford F-450 Cab and Chassis
  • We do not at this time have a custom-fit gooseneck hitch for your 2018 Ford F-450 cab and chassis but we do have hitch fabrication parts like Curt # C65500 which has a rating up to 30K depending on the installation. This hitch does require under-bed reinforcement to reach its maximum capacity.
    view full answer...

  • Plate Thickness of Curt Gooseneck Flat Plate C65500
  • The Curt Gooseneck Flat Plate # C65500 is 3/8-inches thick and measures 13 x 48-inches. This item's 30,000-lb rating is dependent on the specific installation and will require under-bed reinforcement to reach its maximum GTW rating. We offer a universal install kit # C61502 but custom-fabrication is also an option for providing the necessary support under the center of the hitch.
    view full answer...

  • Measuring for the Gooseneck Hitch Ball Hole on a 2018 Ford F-350
  • There are two possible causes that you are coming up just shy of 45-1/2" when installing the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1117 on your 2018 Ford F-350 with the 6-3/4' bed. The first of which would be if you had a spray-on or drop in bedliner. The thickness of the bedliner will need to be taken into consideration when measuring from the rear of the bed to the center hole.The next issue would be the tape measure. Most tape measures do not start at zero. There...
    view full answer...

  • Recommendations for 5th Wheel Trailer Connection With Gooseneck Hitch
  • The Hide-A-Goose Underbed Gooseneck Trailer Hitch - 30,000 lbs # 9466 does not have an adapter that fits in the gooseneck underbed system. It would require an above bed adapter. The underbed systems that work with the hitches have pins that run all the way through the adapter to hold it into the system. For a hitch you can use the Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter - Single Jaw - 21,000 lbs # DM8550045 which attaches to the gooseneck hitch ball. You can...
    view full answer...

  • Gooseneck Compatibility with Hemi Gas Engine on 2011 Ram 2500
  • The Draw-Tite Hide-A-Goose Underbed Gooseneck Trailer Hitch with Custom Installation Kit # 9464-57 is a confirmed fit for your 2011 Ram 2500. It is a custom fit whether you have an 8 foot bed or a 6.5 foot bed. The Hemi gas engine is not a factor in the fit.
    view full answer...

  • Gooseneck Hitch Recommendation for a Cab and Chassis Truck
  • The Curt Flat Plate Gooseneck # C65500 is a multi-fit application that can be used on a cab and chassis truck. Typically, the plate would be placed on top of the flat bed over the rear axle. The Universal Rail Kit, part # C61502 can be used to provide the under bed bracing. Holes would be drilled through the plate, through the bed and into the frame members and the rail kit. At least six 1/2 inch grade 5 bolts need to be used to fasten the plate to the rail kit. At this time there...
    view full answer...

  • How to Use a B&W Companion 5th Wheel Hitch on a 2012 Ram 3500
  • The correct B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter that you will want to use with the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1313 on your 2012 Ram 3500 is part # BWRVK3400-5W if you have a short bed or part # BWRVK3500 if you have a long bed.
    view full answer...

  • Can Safety Chain Loops of Reese Elite Pop In Ball # RP30140 be Used for Breakaway Cable
  • You can use the safety chain loops of the Reese Elite Pop In ball set part # RP30140 for where to attach the breakaway cable. The trick is that you run the brekaway cable lengh slightly shorter than the safety chains length so that in the event of a breakaway the plunger would pull before any tension was put on the chains.
    view full answer...

  • Does Curt Double Lock Hitch part # C607-661 Include Mounting Rails and Hitch
  • The Curt Double Lock Hitch part # C607-661 includes everything needed to install the hitch. It actually is a kitted part number which means it includes the hitch center section as well as the mounting brackets.
    view full answer...

  • Troubleshooting Curt Gooseneck Hitch Ball Stuck in Bed of 2016 Ram 2500
  • The Curt Underbed Gooseneck Trailer Hitch for Ram 2500 # C60614 sounds like the hitch ball has been damaged. I recommend first using a penetrating oil like the UltraLube Biobased Spray Lubricant and Penetrant - 12-oz Aerosol with Straw # L10444 to spray into that hitch ball lever and also around the edge of the hole on the top and bottom. Use a little vibration from a rubber mallet to let the oil find its way into all the bound locations. Let sit for a few minutes and then try again....
    view full answer...

  • Recommended Taller Gooseneck Hitch Ball Compatible with 2018 Ram 3500 Factory Pucks
  • You are correct that the B&W Ball and Safety Chain Kit for Ram Underbed Gooseneck Trailer Hitch # BWGNXA2062 is taller at 5-3/4 inches above the bed. The hitch ball is only available in the kit as you stated. I reached out to my tech contact at Curt and the kit # C60692 will allow the hitch ball to fit your Ram but the safety chain anchors will not fit your Ram pucks. So what you want is the hitch ball # C60629 (and the Ram safety chain anchors # C60617 which came with your original...
    view full answer...

  • Andersen Ultimate Fifth Wheel Hitch in 2018 Ram 3500 With Factory Rail Kit
  • The only way to use the Andersen Ultimate Connection 5th Wheel Trailer Hitch # AM3200 in a 2018 Ram 3500 with the factory puck system is to use an adapter, and I recommend the Reese 5th Wheel Rail Adapter # RP30154. You would not be able to use the safety chains of the Reese Elite Series Pop-In Ball Kit for Ram Under-Bed Gooseneck Hitch # RP30140 because the adapter will mount in the puck holes where the safety chain loops would also mount.
    view full answer...

  • Will the B&W Gooseneck Hitch # BWGNRK1108 Fit a 2005 Ford F-250 with Air Lift Air Bags
  • Would you be able to send me a picture of your air springs and where they are mounted? I don't think that the B&W Gooseneck Hitch # BWGNRK1108 will fit but I may be able to find you another solution to tow a gooseneck trailer. Some of the Air Lift kits are compatible with 5th wheel mounting kits but only certain part numbers.
    view full answer...

  • What Size Hole Needs to be Cut in the Bed of 2016 Ford F-250 for Curt Gooseneck Hitch # C60683
  • To install the Curt EZr Double Lock Underbed Gooseneck Trailer Hitch # C60683 on your 2016 Ford F-250 Super Duty you will need to have a 4" hole in the bed of your truck. This hitch actually comes with a center locator to help make your cut accurate if you don't already have that cutout in your truck bed. Attached are the installation instructions for you to check out.
    view full answer...

  • Cost Effective Gooseneck Hitch for a 2002 Chevy Silverado 2500 HD
  • The odds that the gooseneck hitch you were given is a fit for your truck is slim to none unless it came off of a 2001-2010 GMC Sierra 2500 HD/3500 or a 2001-2010 Chevy Silverado 2500 HD/3500 that is. If not then it would be best to buy a new hitch that is specifically designed for your truck for which the most cost effective option we have is the Fold Down Gooseneck Trailer Hitch with Installation Kit part # 8339-4434. If there is a part number stamped anywhere on the hitch then I may...
    view full answer...

  • Is Center Section of B&W Gooseneck Hitch BWGNRK1000 Available Separately
  • B&W Gooseneck Hitch # BWGNRK1000 is confirmed to fit your long bed 1998 Chevrolet C/K Series Pickup. The center section of this complete hitch is available on its own as part # BWGNRC800.
    view full answer...

  • Inner Gooseneck Hitch Tube and Coupler for 4-Inch Standard Gooseneck
  • I suggest the B&W Extend-A-Goose Gooseneck Coupler # BWTEXA4200 which is designed to fit inside a standard 4-inch diameter outer gooseneck tube. This coupler fits a 2-5/16-inch gooseneck ball and it provides 10-inches of offset for increased turning clearance. Please refer to the linked video for more on this USA-made coupler.
    view full answer...

  • Recommended Air Springs Compatible with B&W Gooseneck Hitch on 1999 Ford F-250
  • The Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle # AL57291 is a confirmed fit for your 1999 Ford F-250 and is designed for compatibility with B&W gooseneck hitches. I've attached a video of this installation to assist. This kit will come with the manual inflation valves for adding or removing air pressure. You also may want to consider adding the Air Lift Load Controller II Compressor System for Air Helper Springs - Single Path # AL25592. This will give you the ability to...
    view full answer...

  • Recommended Gooseneck Trailer Hitch for 2000 Ford F-350 Cab and Chassis
  • There is not a custom fit gooseneck hitch and underbed rails for your 2000 Ford F-350 Cab and Chassis. Your best option is to use the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks - 30,000 lbs # BWGNRK1500 which will require custom welding for installation. Another option is to use the Buyers Products 2-5/16" Fabricators Flatbed Gooseneck Hitch # 3375613500. I've attached a video of each to assist.
    view full answer...

  • Can Fifth Wheel Rails Install on 2007 Chevy Silverado With Curt Gooseneck?
  • The # C640-644 gooseneck you referenced is only a fit for certain year Ford Super Duty trucks and there is not a Quick Goose 2 Gooseneck that fits a 2007 Chevy Silverado. There is an underbed Curt gooseneck for this truck, part # C61652-652, but you would not be able to install fifth wheel mounting brackets and base rails with it. The only thing you can do is remove it and install the B&W Turnoverball Gooseneck # BWGNRK1059-5W for a Silverado 1500, # BWGNRK1067-5W for a 2500, or # BWGNRK1062-5W...
    view full answer...

  • Installing B&W Gooseneck Hitch on 2005 Dodge Ram 2500 with Firestone Air Springs
  • The Firestone Ride-Rite Air Helper Springs # F2299 we have that are confirmed to fit your 2005 Dodge Ram 2500 are indeed compatible with an in-bed hitch like the B&W Gooseneck # BWGNRK1313 that you plan on installing. The brackets for the Firestone air bags install on the bottoms and inboard sides of the frame rails, while the B&W Gooseneck will fit on the outboard side of the rails. There will be no interference between the two systems. I have attached an installation video on your...
    view full answer...

  • Will the Reese Gooseneck Trailer Hitch # RP30845 Fit an elite Series Under-Bed Rail Kit
  • The Reese Elite Series Above-Bed Gooseneck Trailer Hitch # RP30845 is designed for the puck locations of an Elite Series under-bed rail kit. If that is what you have on your 2001 Dodge Ram Pickup then this will definitely work for your application. I tried looking up the specific Elite Series kit for your vehicle but I couldn't find anything. I am not sure if it has been discontinued but I would just double check to make sure that is what you have before ordering this item. A review...
    view full answer...

  • Does Hide-A-Goose Underbed Gooseneck Trailer Hitch Come With Safety Chain Hooks?
  • The Hide-A-Goose Underbed Gooseneck Trailer Hitch with Custom Installation Kit # 9468-94 comes with safety chain u-bolts, like are shown in the accompanying photo. Those u-bolts do come with the kit and if you take a look at the linked installation instructions you can see how they install.
    view full answer...

  • B&W Turnoverball Underbed Gooseneck Trailer Hitch for a 2004 Dodge Ram
  • The correct B&W Turnoverball Underbed Gooseneck Trailer Hitch for your 2004 Dodge Ram would be part # BWGNRK1316 if you have the 1500 model or part # BWGNRK1313 if you have the 2500/3500 model. Unfortunately, we do not offer the frame brackets separately from the hitch. The center section would also have to match the one you see in either of the above in order for it to work with the vehicle specific frame brackets.
    view full answer...

  • B&W Ball and Safety Chain Kit With Andersen Ultimate Hitch
  • We do not carry the Andersen Ultimate Hitch but I looked up the instructions and it fits standard 2-5/16" gooseneck hitch balls so yes, it will work just fine with the B&W Ball and Safety Chain Kit for Ram Underbed Gooseneck Trailer Hitch # BWGNXA2062 that fits your 2018 Ram 3500.
    view full answer...

  • Recommended Aftermarket Underbed 5th Wheel and Gooseneck Hitch Option for 2016 GMC 2500 6-1/2 Bed
  • The best option for you to have a clean bed without rails and have both the 5th wheel and Gooseneck hitch is to use the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs # BWGNRK1016 which also serves as the underbed rail system for the Companion 5th Wheel Trailer Hitch with Slider # BWRVK3400. This combination will give you a clean bed when not in use, a gooseneck hitch, and a 5th wheel sliding hitch compatible with the underbed system that will...
    view full answer...

  • B&W Ball and Safety Chain Kit for a 2018 Ram 2500 with Factory Gooseneck Trailer Hitch
  • Great news: there is a B&W ball and safety chain kit for newer Ram trucks like your 2018 Ram 2500 that have the factory gooseneck and 5th wheel prep package. It is # BWGNXA2062. The one for B&W ball and safety chain kit for Ford, Chevy, and Nissan trucks, # BWGNXA2061, does not have a shank that is the right length with the ball bearings in the right place to fit properly and safely in the Ram factory system.
    view full answer...

  • Air Bag Helper Springs for a 2016 Ford F-150 SuperCrew 4x4 with B&W Gooseneck Hitch Installed
  • Yes we do! We actually have several kits that will work on your 2016 Ford F-150 4x4 with the B&W gooseneck hitch already installed. You can use Air Lift kits # AL57284, # AL88284, or # AL89284. These kits all have upper brackets that attach to the bottoms of the frame rails so they won't interfere with the B&W hitch brackets. All 3 of these kits are rated for 5,000 pounds. The difference is that # AL88284 and # AL89284 have jounce springs inside the air springs and kit # AL57284 does...
    view full answer...

  • Air Bags For 2018 Ford F-150 With B&W Gooseneck
  • The 2,000 lb Air Lift # AL59570 is NOT a fit for your 2018 Ford F-150 with a gooseneck hitch. The air bags with a 5,000 lb capacity should not make your ride harsh; is your current kit one with internal jounce bumpers? What I recommend for your 2018 F-150 is the Air Lift LoadLifter # AL57284, which are air springs that do not have internal jounce bumpers, which is what will give you a stiffer ride if you have a very heavy load. If you have the 5,000 lb capacity Air Lift # AL57284,...
    view full answer...

  • Dimensions of the B&W Ball and Safety Chain Kit Part # BWGNXA2062
  • I went out to our warehouse and measured the B&W Ball and Safety Chain Kit for Ram Underbed Gooseneck Trailer Hitch part # BWGNXA2062 for you. The distance from the base of the ball where it sits atop the hitch to the top of the ball is 5-3/4". I have also attached a few other measurements you may find useful as well. If you need any other dimensions or have any other questions then please feel free to let me know.
    view full answer...

  • Recommended Gooseneck Hitch for a 2006 Ford F-450 Flatbed
  • The best gooseneck hitch we have for your 2006 Ford F-450 Flatbed is the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks part # BWGNRK1500. This hitch has a 30,000 lb weight capacity, removable ball design, and is made right here in the U.S.A. B&W hitches are considered to be one of the best on the market which is why I recommend this hitch for you. I have attached a review video but please keep in mind that this hitch is not a custom fit nor do we have any custom...
    view full answer...

  • Is There a Difference Between B&W Gooseneck Hitches BWGNRK1108-5W and BWGNRK1108
  • There is no difference between those two part numbers on your end. If you ordered either part number you'd get the same B and W Turnoverball Gooseneck Hitch part # BWGNRK1108. We have two part numbers though as this hitch shows up in the gooseneck and fifth wheel fitguides since Companion hitches like the part # BWRVK3400 fit it directly. The two part numbers allow us to organize them in our system and fitguides easier.
    view full answer...

  • Air Suspension System Compatible with B&W Gooseneck System on 2004 Ford Super Duty Truck
  • On your 2004 Ford F-Series Super Duty, the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit # BWGNRK1108 is a confirmed fit. There are many options for the Air Lift 5,000 system but only a few will work with that hitch. I recommend the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle # AL57393 for 2WD models or # AL57390 for 4WD models. These will work without modifications. If you want to add the compressor system to adjust your psi at any time,...
    view full answer...

  • Does Above The Bed Goosenecks Work With Slide In Truck Campers?
  • The Fold-Down Gooseneck Trailer Hitch with Installation Kit # 8339-4435 is an above the bed unit that sticks up on the truck bed where it may interfere with applying a slide in truck camper to your bed, even when its folded down. When I spoke to my contact at Draw-Tite, they said if your truck camper can clear 3/4" (distance from door that holds the ball up to the truck bed) then it may fit. When planning to apply to slide in truck camper in the bed of your truck, I recommend a below...
    view full answer...

  • Recommended Replacement for Factory Gooseneck Hitch Ball in a 2017 Ram 2500
  • I have exactly what you need to use your Andersen Ultimate Connection 5th Wheel Trailer Hitch System (Gooseneck Version) in the bed of your 2017 Ram 2500. For this, I recommend the Reese Elite Series Pop-In Ball Kit for Ram Under-Bed Gooseneck Hitch part # RP30140. This kit comes with a 2-5/16" hitch ball, two safety chain loops, and a handy storage bag. It will fit perfectly into the gooseneck cutout you have in your bed. There are currently no recalls on the Reese Elite Series Pop-In...
    view full answer...

  • Gooseneck Hitch for 2013 Toyota Tundra With 5-1/2 Bed
  • While there is a gooseneck hitch that will fit the 5-1/2' bed on your 2013 Toyota Tundra the Curt Double Lock # C60751 is not a fit. Instead, I recommend the Draw-Tite Hide-A-Goose Underbed Gooseneck Trailer Hitch with Custom Installation Kit # 9465-36. The accompanying photo shows this hitch installed on a '13 Tundra so you can see just how it will look. With your bed size you would not be able to place the ball in the upside down position, and you may also need to use 5" Offset Ball...
    view full answer...

  • What Air Bags Work with the B&W Turnoverball Part # BWGNRK1117 on a 2018 Ford F-250
  • The airbags that I recommend for your 2018 Ford F-250 are the Air Lift LoadLifter 5000 Air Helper Springs part # AL57399. These airbags will not interfere with the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1117 as you can see in the attached photo. The Air Lift airbags will do an excellent job of improving both safety and ride quality. They are adjustable which means you can inflate each spring independently for side-to-side leveling of off-center loads. The kit...
    view full answer...

  • Carton Dimensions and Weight of B&W Turnoverball Underbed Gooseneck Trailer Hitch BWGNRK1067
  • B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1067 has a shipping weight of 112-lbs and the carton dimensions are 58 x 8 x 25.
    view full answer...

  • Will the B&W 4 Inch Offset Ball Part # BWGNXA4085 Fit the B&W Turnoverball Part # BWGNRK1111
  • Yes, the 4" Offset Ball for B&W Turnoverball Gooseneck Trailer Hitches part # BWGNXA4085 will fit perfectly with the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1111 which is a fit for your 2016 Ford F-350. The offset adapter as I am sure you already know will improve turning clearance for a short bed truck. I have attached a review video of the offset hitch ball and install video of the hitch for you as well.
    view full answer...

  • Will the Gooseneck Hitch from a 2012 Dodge Ram 3500 Crew Cab Fit a Mega Cab Model
  • I do have the correct gooseneck hitch for your 2012 Dodge Ram 3500 Mega Cab but the gooseneck hitch for a 2012 Dodge Ram 3500 Crew Cab will not work. The hitch you have now is the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1313 and the hitch you need is the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1308 which is designed specifically for Mega Cab models but will also work on the other cabs as well. I have attached an install video of the correct...
    view full answer...

  • Recommended Gooseneck Hitch with 3 Inch Ball for 2018 Ford F450 Cab and Chassis Flat Bed
  • For your 2018 Ford F-450 Cab and Chassis with Flatbed, the best gooseneck hitch option is the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks - 30,000 lbs # BWGNRK1500. This is a weld in application. Then for a 3 inch ball instead of the standard 2-5/16 inch ball, you will use the 3 inch Hitch Ball for B&W Turnoverball # BWGNXA2025.
    view full answer...

  • Gooseneck Hitch Recommendation for 2016 Dodge Ram 2500
  • For your 2016 Ram 2500 we have a few gooseneck hitch options that will work well. The one I would recommend is the B and W Turnoverball part # BWGNRK1384 which when not in use would allow you to flip the ball upside down and reinsert it back into the hitch's center section.
    view full answer...

  • Recommended Curt Double Lock Flip and Store Underbed Gooseneck for 1997 Ford F-350
  • The Curt Double Lock, Flip and Store Underbed Gooseneck Hitch w/ Installation Kit - 30,000 lbs # C60721 is a fit for only 2004 - 2014 Ford F-150 6-1/2 Foot Bed and 2004 - 2014 Ford F-150 8 Foot Bed. For the same hitch that will fit your truck, you will want # C60723 which is a fit for 1997 Long Box XL crew cab models with or without overload springs. You may also want to consider adding a second 7-way connection to the bed of your truck using harness # 20023 for easy connection access.
    view full answer...

  • Dimensions of Fold-Down Gooseneck Trailer Hitch with Installation Kit # 8339-4439
  • I spoke with my contact at Draw Tite and he informed me that the dimensions of the Fold-Down Gooseneck Trailer Hitch with Installation Kit # 8339-4439 is 12 inch by 14-1/2 inch.
    view full answer...

  • Airbags for 2016 Chevy Silverado 3500 With B&W Companion Fifth Wheel Hitch
  • Yes, you can use airbags on your 2016 Chevy Silverado 3500 with the B&W # BWGNRK1016 installed. I highly recommend the Air Lift LoadLifter 5000 Air Helper Springs # AL57338 that has included hardware that is designed to be used on trucks with fifth wheel hitch brackets; the only thing to note is that you will need to drill into your Silverado's frame in order to install airbags. The LoadLifter 5000 allows you to adjust the air pressure of each bag individually from 5 psi to 100...
    view full answer...

  • Underbed 5th Wheel Install Kit with Gooseneck Hitch for a 2017 Ford F-350 King Ranch
  • Reese Elite Series 5th wheel installation kit with gooseneck hitch # RP30138-26 only fits up to the 2016 Ford F-350 and will not fit a 2017 but there are other options for the 2017 for both a gooseneck hitch and underbed 5th wheel install kit. If you have a 2-wheel drive model you can use B&W kit # BWGNRK1116-5W. This is a gooseneck hitch that accepts the Companion hitch, # BWRVK3400-5W for a short bed or # BWRVK3500-5W for a long bed. If your truck is a 4x4 then the install kit is...
    view full answer...

  • Small Gap Between Socket on B&W Turnoverball Gooseneck Hitch and Truck Bed
  • The 4 inch hole that you cut in your truck bed in order to install the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1117 is correct. The slight gap that you have between the socket for the hitch ball and your bed is not an issue. As long as you have the bolts for the center plate tightened according to the torque specs listed in the instructions, the hitch isn't going to move at all after installation. I have attached an installation video on your 2017 F-350 that you can...
    view full answer...

  • 3" Gooseneck Hitch Ball Needed for a 2017 Ford F-350 with OEM Pucks
  • For a 3" gooseneck hitch ball that is compatible with the OEM puck system on your 2017 Ford F-350 Super Duty we have the Reese Pop-In Ball # RP19314 which has a 30K weight capacity. For the safety chain loops you can use part # RP58468. Unfortunately the B&W Ball and Safety Chain Kit # BWGNXA2061 that you referenced does not come in a 3" gooseneck ball version, only the 2-5/16" for the OEM puck system in your F-350.
    view full answer...

  • Gooseneck Trailer Hitch Installation Rail Kit for 1999 Dodge Ram
  • Yes, just the installation kit from the Fold-Down Gooseneck Trailer Hitch with Installation Kit - Dodge Ram Trucks # 8339-4439 is available. What you need for your 1999 Dodge Ram is the Gooseneck Trailer Hitch Installation Rail Kit - Dodge Ram Trucks # 4439. You can find the price for this directly on the product page.
    view full answer...

  • Recommended Fold-Down Gooseneck Hitch For 1999 Ford F-250
  • I do have a great option for you, however we do not currently have the Atwood model gooseneck hitch that you mentioned available for your truck. For a very similar gooseneck hitch that is confirmed to fit your 1999 Ford F-250 Short Bed, I recommend taking a look at the Draw-Tite Fold-Down Gooseneck Trailer Hitch # 8339-4448. This gooseneck hitch includes custom frame brackets that will eliminate the need for drilling into the truck's frame. Its fold-down ball will allow for uninhibited...
    view full answer...

  • Towing Capacity of 2017 Toyota Tundra Crewmax 5.7L V8
  • According to pages 167-169 of the online owner's manual for your 2017 Toyota Tundra Crewmax 5.7L V8 the most trailer weight this truck can tow is 10,100-lbs. You will want to refer to your printed manual too since this maximum capacity depends on the specific engine and drivetrain and whether or not you have the optional towing package. Many versions have lower capacities. You can also check with your local dealership using the truck's VIN. For 5th wheel towing in this truck your 5-1/2-foot...
    view full answer...

  • Does B and W Gooseneck Hitch # BWGNRK1217 Fit 2017 Nissan Titan XD Long Bed
  • The B and W Gooseneck Hitch part # BWGNRK1217 that you referenced does fit the long and short bed versions of the 2017 Nissan Titan XD so this would fit and work well for you.
    view full answer...

  • Can the Gooseneck Hitch Ball Be Stored in the Upside Down Position on a 2015 Toyota Tundra
  • You are correct, the Hide-A-Goose Underbed Gooseneck Trailer Hitch part # 9465-36 for your 2015 Toyota Tundra will not allow the hitch ball to be stored inside the hitch upside down due to the chance of interference with the differential housing and/or brake lines. This fit error will be the same for all of the gooseneck hitches we have for your Tundra. Unfortunately, there is not way around the issue due to the design of the truck.
    view full answer...

  • Gooseneck Hitch, Wiring, Brake Controller and Spring Kit on 2014 Silverado 1500 with 5-1/2-Foot Bed
  • For your 5-1/2-foot bed 2014 Silverado 1500 I suggest the Draw-Tite Gooseneck hitch # 9465-54 along with the Offset Ball # 19308 and wiring harness # 20110. An install video is included for you. For a trailer brake controller I suggest the highly-reliable Prodigy P3 # 90195 along with the quick-connect install harness # 3016 which plugs in under the dash. The P3 offers easier installation and set-up than most other controllers and it has a legendary reputation for reliability. An install...
    view full answer...

  • Recommendation for 20,000 Pound 5th Wheel Hitch to Use with Draw-Tite Gooseneck Hitch
  • I may have a solution for you, however the Draw-Tite Hide-A-Goose Underbed Gooseneck Trailer Hitch # 9465-54 that you have installed in your Chevy Silverado is not compatible with the B&W Companion Hitch # BWRVK3500. This is because the B&W Companion is designed to fit the square gooseneck hole that the B&W gooseneck hitches provide, and it will not fit the round gooseneck hole on your Draw-Tite unit. There is not an adapter available to make the two systems compatible with each other....
    view full answer...

  • Will B&W Gooseneck Hitch Fit on 2003 GMC Sierra 6-1/2' Bed with Spray-In Bed Liner
  • The spray-in bed liner for your 2003 GMC Sierra isn't thick enough to cause any issues for the installation of the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1067. The only time that a bed liner is an issue is when it is a drop-in bed liner and even then you would still be drilling through the entire bed of your truck so the measurements and holes sizes wouldn't change. If you are going to be towing a gooseneck trailer with your Sierra then you will want to use a hitch...
    view full answer...

  • Will Air Bag Kit Fit on a 2015 Toyota Tundra with a B&W Gooseneck Hitch # BWGNRK1257
  • I do have a solution for you to add a suspension enhancement system (SES) to your 2015 Toyota Tundra but unfortunately none of our air bag kits are compatible with an in-bed hitch like the B&W # BWGNRK1257. We offer a variety of jounce and leaf style SES for you to choose from. I recommend using the SumoSprings Helper Springs # SSR-610-54 which replace your factory bumpstops and provide extra support up to 2,800 lbs. Please note that any SES is designed to work with a suspension system...
    view full answer...

  • Will B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1500 Fit CM SK Truck Bed
  • The B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1500 that you referenced is a universal application that is welded on to steel flatbeds when it comes to the installation. It isn't fitguided to fit your CM SK truck bed but as long as its steel you can reference the linked installation instructions to ensure fitment. I confirmed this with my contact at B&W.
    view full answer...