Filter Questions and Answers:

reset filter

Expert Answers about Enclosed Trailer Parts


  • Shelving Options That Mount to Trailer Wall
  • There may be a solution for you though the Traffic Cone Holder for E-Track or Rack'em Spare Tire Holder # RA-26 does not have a specific weight rating for one of the brackets. There are a couple options for you to consider like the CargoSmart Rotating Board Holder for E-Track and X-Track Systems # 3481740, which will require you to provide your own shelving. I believe this may have been what you were referring to by something like the cone holder with the bar laying flat in the bracket....
    view full answer...

  • Is Trailer Ramp Hinge Part # HP12412G Weldable
  • Actually the 1/2" Diameter Greasable Hinge Pin # HP12412G is not zinc coated or galvanized. It was designed to be welded so there wouldn't be an issue if you did so. It's not the prettiest weld, but I did attach a picture of this welded to a trailer for you to check out as well.
    view full answer...

  • Difference Between Fan-Tastic Vent Roof Vent # FV801200 and # FV801208
  • The Fan-Tastic Vent Roof Vent w/ 12V Fan # FV801200 and the Fan-Tastic Vent Roof Vent - Clamp On # FV801208 referenced in your question are indeed extremely similar to each other. These are both variable-speed, 12-volt roof vent fans designed for a rough opening size of 14-1/4 inch x 14-1/4 inch. As far as the units themselves, these products are virtually identical. The only real difference between the two models is the manner in which they install. The Fan-Tastic Vent Roof Vent -...
    view full answer...

  • Replacement Motor and Diagram for Ventline Vanair Trailer Roof Vent
  • The correct replacement motor for the Vanair Roof Vent part # VP-543SP that you referenced is the part # BVD0218-00. I attached a diagram that covers how it all comes apart for you to check out which should help you in getting out the old vent to install the new one. I also attached install instructions for the motor for additional reference although you may not need them.
    view full answer...

  • Replacement Parts for Fan-Tastic Vent 8000 Series
  • There is not a fuse we carry for the 8000 Series of Fan-Tastic vent. It does use a 4 amp slow blow fuse so to make fuse access simpler you can use In-Line Fuse Holder # C58470-1 and if you need to replace the bow-tie bracket, motor, and blade the correct part is Replacement Fan Motor Assembly Kit # FVK8017-00
    view full answer...

  • Compatibility and Weight Capacity of O-Track Systems
  • We have previously tested the Erickson and Tow-Rax O-Track Systems and found them to be compatible with each other. I went out to our warehouse to test the Erickson Anchor Ring # EM59132 on the Buyers Product Super Track # 337ST93 and found it to be compatible as well. This means the O-Track components from all three of the manufacturers you mentioned are indeed interchangeable and will work well each other. The tie-down rings included with the Buyers Products Super Track Kit actually...
    view full answer...

  • What Is The Difference Between The Fan-Tastic Roof Vents FV801250 and FV801350
  • You have asked a great question. The difference between Fan-Tastic Vent Roof Vent part # FV801250 and Fan-Tastic Vent Roof Vent part # FV801350 is the garnish. The garnish (or base) that comes with the vent part # FV801250 is 4 inches thick compared to the garnish (or base) that comes with the vent part # FV801350 is a low profile 1-1/2 inches thick. The FV801250 fits trailers roofs up to 4 inches thick and FV801350 is better for thin roofs like enclosed trailers with thin metal roofs....
    view full answer...

  • Replacement Roof Vent Cover for 2000 Skamper Sport 23D Pop-Up Camper Trailer
  • Thank you for the photo of your trailer roof vent for which you need a new lid. I conferred with several of my associates regarding the photo of your trailer roof vent which requires a replacement lid. Interestingly, this hinge design seems about halfway between a 3-point type like # 69284 and a continuous type like # BV0554-01. After much back and forth we came to the determination that you need a 3-point. We have only two options for a 3-point-hinge type lid, parts # 69284 and...
    view full answer...

  • MaxxAir Roof Vents for RVs with Thermostats with Manual Lift and Powered Lift
  • You are correct and all of the settings of the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote # MA00-07000K that you mentioned are correct. The powered lift can be turned off to allow you to manually lift the lid, this is thermostatically controlled, and due to the lid design it could be open and vent while raining. This is due to the vents being underneath the lid. I attached a picture that shows what the display looks like for the temperature setting. The smoked color...
    view full answer...

  • Replacement Lid for Heng's Roof Vent Model 122112
  • I found some photos of the Heng's Roof Vent 122112 online. Based on this, it looks the correct replacement for you should be the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents part # BV0554-01 for white or part # BV0554-03 for black. In order to confirm this you would just need to make sure your roof vent has a continuous hinge (see photo). If you are not sure please just send me a photo of what you have and I will confirm. These covers are both 14-1/2" x 14-1/2".
    view full answer...

  • Motor On MaxxAir MaxxFan 4900K Roof Vent Will Not Shut Off When Lid Is Closed
  • I spoke with MaxxAir about the issues you are having with your MaxxAir MaxxFan Roof Vent and they informed me that the gears inside the lift motor have gone bad so you will need to replace this with the Replacement Lift Motor for Maxx Fan Plus Roof Vent part # MA10-20270. I was also able to confirm that the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents part # MA10-20281K-1AF is correct for you so that is not the issue.
    view full answer...

  • Is There a Correct Size for a Fan-Tastic Roof Vent on a Haulmark Edge Trailer?
  • Based on my research, your Haulmark Edge race trailer has a standard 14" x 14" roof vent, which requires a 14-1/4" x 14-1/4" opening. If you are concerned about roof thickness, the Fan-Tastic vent's roof garnish - such as the one in the photo that I've attached - can be trimmed to meet your specifications. The only thing left for you to do is choose which vent you prefer. The most popular of our Fan-Tastic roof vents is # FV801200, which has a manual-speed knob to let you control airflow....
    view full answer...

  • Replacement Cover for Trailer Roof Vent AS-13 M-VD0449
  • We have actually spoken with Ventline regarding your model AS-13 M-VD0449 in the past and they have confirmed that the correct replacement cover is the part # BVD0449-A03 in Smoke or # BVD0449-A01 in White. The cover measures 14 inches x 14 inches and is designed for a continuous hinge. I have attached a couple short video reviews on these covers that you can check out as well.
    view full answer...

  • Easy to Use Ladder Rack Options for an Enclosed Trailer
  • I do have an easy way that will allow you to carry multiple ladders on your enclosed trailer, however, none of them mount to the roof and tilt down for loading/securing. I recommend using the Pack'Em Ladder Rack part # PK-28WL2-BM as this will be your best option. The Pack'Em ladder racks attach to the exterior walls of your enclosed trailer and will allow you to carry up to 2 ladders on each side of the trailer without having to climb up on the roof to secure them. As long as your...
    view full answer...

  • Comparing MaxxFan Deluxe 12V Roof Vent Models MA00-07000K and MA00-07500K
  • The two MaxxFan Deluxe 12V Roof Vent products you referenced, parts # MA00-07000K and # MA00-07500K, are identical apart from color. The smoked lid model # MA00-07500K will typically let in slightly less light than the white lid model # MA00-07000K but there is not a huge difference. Price variance between the different color versions of the same product can be a result of different production quantities. If one is far more popular and made in much larger quantities it will typically...
    view full answer...

  • Is the MaxxFan Deluxe Roof Vent # MA00-06401K Exhaust Only
  • The MaxxFan Deluxe Roof Vent # MA00-06401K that you referenced is exhaust only. For a MaxxAir MaxxFan that has the dual functions of exhausting air or pulling the air in in we have part # MA00-06200K or part # MA00-07500K. The big difference between these 2 models is that part # MA00-07500K comes with a remote that you can use to activate the different functions while part # MA00-06200K has a flush mounted keypad instead. I have attached review videos on all 3 fans for you to check...
    view full answer...

  • Does Conventional Ramp Door Spring # 362SA7 Come with Rods for Winding Spring
  • The Conventional Ramp Door Spring # 362SA7 that you referenced was designed to be taken to a professional with experience winding torsion springs like a garage door company. It does not come with the tools typically needed to wind the spring. In the review video I attached you can see everything that comes with this as well.
    view full answer...

  • Comparing O-Track Cargo Control System And L-Track System
  • I did some research and found that the Erickson O-Track Cargo Control System like part # EM59133 is very similar to the L-Track systems you referenced. The Erickson O-Track is 18 inches long and includes 2 Spring-loaded O-ring clips and mounting hardware. These can be mounted on a wall or on the floor giving you versatility for securing cargo. I have attached a photo that shows what the weight capacities of the clips are when installed. I have attached a product review video for the...
    view full answer...

  • Differences Between Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Covers FVU1400GRS and FVU1500G
  • The difference between the Fan-Tastic Vent vent covers # FVU1400GRS and # FVU1500GR is in the models of vent that each one will fit, as you noted. Part # FVU1400GRS fits all Fan-Tastic Vent trailer roof vents with model numbers starting with "DF". Part # FVU1500GR fits all Fan-Tastic Vent trailer roof vents with model number starting with "FA" or "FV". You certainly can use your own preferred installation hardware. Both vent covers will also work with standard and powered vents from...
    view full answer...

  • Supplies Needed to Install Replacement Ceiling Vent
  • The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat # MA00-06200K will install in the exact same cutout as the stock vent. You will simply need some sealant and screws. Many will choose to use the Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White # 344270KITW. You don't absolutely need both butyl tape and sealant, so many will use the LaSalle Bristol XTRM Universal Self-Leveling Sealant - White - Qty 1 # 34427034145-1 or # 0160297 and then the Zinc Sheet Metal Screw...
    view full answer...

  • Best Mounting Orientation of WAVT2-WHMAV2 2-Piece Polypropylene Trailer Vent
  • If you mount the Redline 2-Piece Polypropylene Trailer Vent # WHMAV2-WAVT2 with the exterior part's flat slotted side facing forward (to increase air flow) there will definitely be a greater probability for rain and splashed water to enter the trailer. Still, as you noted from the customer-submitted photos we show on that item's page some have done this, and surely for the same reason. If you happened to stay in dry/desert areas this will be less of a concern but since you are in the...
    view full answer...

  • Which Piano Hinge will Work the Best on a Trailers Ramp Extension
  • Determining between piano hinges, # H300 3 Inch Wide Steel 6 Ft Long or # SH200 2 Inch Wide Stainless Steel Hinge 6 Ft Long, depends what features you find more important for your application. The # H300 hinge will be stronger in that it is an inch wider than the # SH200. Plus, the extra width will allow for more surface area on the hinge to mount to the trailer making for a stronger hinge. However, if weather conditions are a concern, the # SH200 is made of stainless steel. The stainless...
    view full answer...

  • Why Can't MaxxFan Deluxe Roof Vent w/ 12V Fan be Installed Above Tub/Shower
  • While we have heard of people using electrical vents like the MaxxFan Deluxe Roof Vent w/ 12V Fan # MA00-06401K above a tub/shower, it is not meant to be installed in that location because water from the shower (whether it is from steam or from someone dancing around while singing in the shower) can harm the electrical components and cause the vent to fail. This is the same reason why you shouldn't use this above a range cooking surface either. If you like the idea of having a rain cover...
    view full answer...

  • Replacement Motor Assembly for Fan-Tastic Roof Vent With 12V Fan
  • It sounds like you have Fan-Tastic Vent Roof Vent # FV801250, which has reverse flow, a 3-speed fan and no rain detector. If this is your fan you need the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00, which replaces the bow-tie bracket, motor, and blade for your vent.
    view full answer...

  • MaxxAir Vent Cover for Fan with 4 Mounting Tabs
  • We actually have a few different version of the white rain covers from MaxxAir. The MaxxAir II # MA00-933072 that you referenced comes with the pins for one side and the hinges for the other side. This is for applications where the roof vent has the mounting tabs on one side. Since you have the 4 mounting tabs on your MaxxAir 4000K you want the MaxxAir FanMate # MA00-955001 which comes with the 4 clips and the 4 brackets. I have attached a video demonstrating this part for you to check out.
    view full answer...

  • Vent Cover for a Fan-Tastic Vent with Powered Lift
  • Fan-Tastic Vent actually has a vent cover. Take a look at # FVU1500BL. It was designed to work with all Fan-Tastic Vent trailer roof vents. There is also a white version # FVU1500WH. We also have cover # FVU1500GR which will work with Fan-Tastic Vent model numbers starting with "FA" or "FV". And we have # FVU1400GRS which works with Fan-Tastic Vent model numbers starting with "DF". Assuming the cover mounting surface is no lower than the vent mounting surface you should have no problems...
    view full answer...

  • Recommended Replacement Vent Cover for Fan-Tastic Vent on RV
  • The Camco vent cover is not intended to work with the Fan-Tastic vents, so I am sorry that you had someone install an inefficient and less than ideal product saying they were compatible. You should have had the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover - 23" x 19.5" x 10.25" - Smoke # FVU1500GR installed instead. It comes in the gray mentioned as well as black # FVU1500BL or white # FVU1500WH. This cover does not use a screen but instead utilizes the screen of your vent itself....
    view full answer...

  • Troubleshooting MaxxAir Vent Powered Lid that Won't Open
  • I've attached the owners manual for your 4900K model which is similar to the # MA00-04500K model. It sounds like your operator mechanism is bad according to my tech contact at MaxxAir. For your 4900K model you will want the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents # MA10-20281K-1AF. If you can't even manually lift the lid, this mechanism is definitely the issue.
    view full answer...

  • Do CargoSmart Shelf Track Brackets have a Weight Rating
  • I reached out to a representative of CargoSmart who told me the CargoSmart Shelf Track Brackets # 3481726 do not have a specific weight rating because there are so many variables in regards to how many brackets you are using, how far apart they are mounted and how the E-Track or X-Track system is mounted. I was told that if it was something relatively light, in the neighborhood of 100 lbs there would not be any type of issue but putting a specific rating on the Shelf Track Brackets # 3481726...
    view full answer...

  • Replacement Remote Control for MaxxFan Plus Roof Vent
  • If you have the MaxxFan Plus roof vent, part # MA00-04500K, then the replacement remote control you need is part # MA00A01150K.
    view full answer...

  • Replacement Hinge for Horse Trailer Tack Room Door
  • We have many types of horse trailer door hinges that you can see on the linked page. I do recommend taking a look at the Polar Flush Hinge # PLR104SS. The photo of this item that I linked includes overall dimensions as well as the center to center mounting hole spacing. If this and the others shown on the linked page do not fit your application please feel free to send us a photo along with dimensions and we'll try to help you find the best option in a replacement.
    view full answer...

  • Comparing MaxxAir II and MaxxAir FanMate Roof Vent Covers
  • Aside from the MaxxAir II having inside dimensions of 21-1/2" long x 18-1/2" wide x 6" tall and the FanMate having inside dimensions of 26-1/2" long x 16-3/4" wide x 9-1/2" tall, the MaxxAir II comes with a bug screen but only 2 of the 4 mounting points use clips that can easily be removed. The FanMate doesn't come with a bug screen (but one can be added with part # MA00-955202 Black or # MA00-955203 Smoke) and it comes with 4 easily removable clips. I have attached video reviews for both...
    view full answer...

  • Weight Rating Of Seal Strap Hinge
  • I checked with my contact at the manufacturer regarding the Over the Seal Strap Hinge # PLR2116. It does not have a particular weight rating. This unit is designed to bridge door molding or a door seal. It is made in the USA and made from high quality steel. For a move heavy duty product I recommend Hinge # PLR109-SS to mount your swinging barn doors.
    view full answer...

  • How to Fix Clicking Noise Coming from MaxxFan Deluxe Roof Vent
  • The clicking noise that you are hearing from your MaxxFan Deluxe Roof Vent # MA00-07500K or # MA00-07000K actually means you need to replace the Operator Mechanism # MA10-20281K-1AF. I reached out to my contact at MaxxAir who confirmed this.
    view full answer...

  • Ramp Springs Compatible With 1982 Circle J 2-Horse Trailer
  • I have a couple solutions for you, but we don't carry the exact springs you are referring to. I recommend the Ramp Spring - 2K Torque for 1-1/2" Shaft - Right Hand # RS16933RH and Left Hand # RS16933LH. These springs are 11 inches long and have a 1-1/2 inch shaft and are 2-1/2 inches wide. The inner diameter of the coil is 1-1/2 inches. Another option is to use the Enclosed Trailer Ramp Spring - Dual Spring, 81" Wide # ERS120D81. I've attached a photo with all of the measurements...
    view full answer...

  • Size of Replacement Vent Cover for Roof Vent on 2008 StarCraft Pop-Up Camper Model 2107
  • The majority of square trailer roof vents are a standard size, about 14 x 14-inches. I found a few photos of your StarCraft camper trailer and it does appear that this is the size on yours. The replacement vent lids we offer come in many colors and in four basic hinge types. You can use any color you want but you need to match the hinge type to ensure a good fit. Please refer to the linked photo that illustrates the various types of hinges used on roof vents. Find your type and then...
    view full answer...

  • Availability of Replacement Roof Vent with Fan and Remote for RV
  • The Fan-Tastic Vent Roof Vent Assembly Kit # FV807357 is not a universal fit fan setup so I can't guarantee it will work for you unless you have a Fan-Tastic roof vent currently. The only type of solution I could provide that I can guarantee will work is an all new roof vent with fan and remote like the # FV807350 which would replace the entire assembly you have now.
    view full answer...

  • How to Select Roof Vent Lid for Motorhome
  • Hi! While there is not a database of parts for each year, make and model of trailer or motorhome there is likely going to be a roof vent lid that works for you. For example the Replacement Dome for Fan-Tastic Vent RV Roof Vents # FVK1020-19 is close to 15" x 15" and fits Fan-Tastic Vent models FV801200, FV801208, FV801250, FV807350, FV802250, FV803350, and FV800900. You also need to know the hinge style of your vent, and I have attached a diagram which displays the different style of...
    view full answer...

  • Troubleshooting MaxxAir Maxxfan 7000K Making Noises When Closing
  • I reached out to the manufacturer and their tech said he is confident the operator mechanism is what is causing your issue. You will want part # MA10-20281K-1AF to replace this and fix the issue.
    view full answer...

  • Replacement Roof Vent Cover for Lid Marked AS-13M-VDO449 ANS Z26 1
  • We have had a similar question to this come up and we were able to determine that the number AS-13 M-VDO449 that you listed is stamped on the vent cover part # BVD0449-A01. If you are looking for the entire fan setup and not just the cover you would want the part # V2092SP-28 for a white lid or part # V2092SP-29 for a smoked lid. The smoked lid would allow more light in.
    view full answer...

  • Door Hinge Bracket with 4 Inch Width
  • We don't have exactly what you are looking for. The # PLR1904-Z you referenced is 3-1/8 inch without the strap. The best other option is the Ramp Door Hinge - Steel # PLR1902 which utilizes as different hinge style and welds flat. It is 4 inches wide but without the bend. These are the only ramp door and dump door hinges we carry.
    view full answer...

  • Availability of Clamp-On Style 12V Roof Vent
  • I do have a great option for you, however the Fan-Tastic Vent Roof Vent # FV801350 that you referenced uses mounting screws to attach to the roof of the trailer and is not a clamp-in style unit. The only clamp-in style vent fan we currently have available is the Fan-Tastic Roof Vent # FV801208. This particular model features a 12V fan with 3 different speeds to help boost and reduce airflow as needed and will clamp onto roofs that are up to 4-1/2 inches thick I have attached a short...
    view full answer...

  • Getting Replacement Keys for Blaylock Trailer Coupler Locks
  • We can help as long as you know which key number you need. It would have been stamped on the initial keys you had. We have a total of 5 key replacements for Blaylock locks like the # BLDL-80 that you referenced. Blaylock Industries Replacement Key 51131: # BL040-TL38KEY51131 Blaylock Industries Replacement Key 51132: # BL040-TL38KEY51132 Blaylock Industries Replacement Key 51133: # BL040-TL38KEY51133 Blaylock Industries Replacement Key 51134: # BL040-TL38KEY51134 Blaylock Industries...
    view full answer...

  • Replacement Vent Cover for Ventline AS-13m-VA123 ANS Z26
  • Ventline vent cover # BV0554-01 is the correct model replacement vent cover for your trailer vent. It has one long continuous metal hinge and is 14-1/4 inches square inside where it goes over the vent assembly. Based on your part number this is the correct item. If this does not resemble your vent lid you can refer to the linked photo to help identify which hinge type you need.
    view full answer...

  • Recommended Handle Latch Kit for Barn Door on Dump Trailer
  • For the barn door on your dump trailer, I recommend looking at the Cam-Action Lockable Door Latch Kit # 383200. This is a nice steel cam-action door latch with a 1 inch wide hasp that can be installed flush on doors with a 3/4 inch offset. It features a bridge-type hasp that will help to prevent accidental opening and secures a safe latching action. This will use a 3/4 inch diameter pipe that you can source from a local hardware store. This will be a simple bolt-on installation. I have...
    view full answer...

  • Big Tex Trailer Ramp Replacement Springs
  • We only carry the springs for those heavy duty style ramps. For the springs we have the Ramp Spring - 2K Torque for 1-1/2" Shaft - left hand # RS16933LH and corresponding right hand # RS16933RH. The other parts will need to be either straightened or replaced and custom welded into place.
    view full answer...

  • Recommended Ramp Torsion Spring for 82-Inch Wide Enclosed Trailer
  • The best size of trailer ramp spring for your trailer is going to be the 81-inch dual torsion spring # ERS120D81. This dimension is the end-to-end length as you'll see in the video. This unit consists of two torsion springs on one shaft and it has a capacity of 120-lbs. This spring can be bolted or welded to the trailer header and it comes complete with dual cables and hardware. Please note that this spring is intended to be installed by someone who has experience with torsions springs....
    view full answer...

  • Installing E-Trac To Build Shelves In Fiber Glass Box Truck
  • There will still be metal studs behind the fiber glass wall in the box truck, so you want to purchase a stud finder that is capable of detecting metal studs to attach your track to. I am not entirely sure what you are trying to build when you mention rafters but it sounds like you may be trying to build a shelf like in the pictures I have attached. You can use the E-Track Wood Beam Socket part # 59149 and horizontal or vertical e-track (depending on what you are trying to accomplish) like...
    view full answer...

  • Recommended Roof Vent for Shallow Clearance Application on Sprinter Van
  • The Ventline Vanair Trailer Roof Vent w/ 12V Fan - 6-1/4" Diameter - Smoke # VP-543SP will allow you to move air at 100 cubic feet per minute. For the low profile ability, these are really your best bet. To feel the air moving, with the windows cracked you will want two instead of one. If you go with the MaxxFan Plus Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke # MA00-04500K you will move much more air with a 900 cubic feet per minute fan, but you will...
    view full answer...

  • Replacement Vent Cover for Hengs Model 122112 Roof Vent 90110 C1
  • I was able to find a picture of the part number 90110 C1 that you need and found that the exact replacement is the # BV0554-03 that you referenced. If you wanted white instead you'd want # BV0554-01.
    view full answer...

  • Can Fan on MaxxFan Deluxe Roof Vent # MA00-05301K Operate in Reverse
  • I spoke with my contact at MaxxAir regarding the MaxxFan Deluxe Roof Vent # MA00-05301K that you referenced. He stated that the printed circuit board on this unit would not be able to handle reversing the polarity. Doing this would likely burn up the circuit board. Your best option is to go with the MaxxFan Deluxe Roof Vent # MA00-05100K instead, which does feature a reversible fan that can bring air in or exhaust air out. Like the unit you were looking at, this fan is designed to fit...
    view full answer...

  • Continental Cargo Trailer Roof Vent Lid Recommendation
  • Based on the number and picture you gave me I was able to determine that you have a Ventadome style roof vent from Ventline so the correct replacement lid is the part # BVD0449-A01.
    view full answer...

  • Will MaxxAir 4951KS Lid Open All the Way when Using MaxxAir II Vent Cover
  • The MaxxAir vent cover # MA00-933073 will allow MaxxFan and MaxxFan Plus models to open all the way. However for those models the FanMate cover is recommended, # MA00-955003. I have linked a couple of videos on the FanMate cover for you.
    view full answer...

  • Key Locking Handle with 5/16 Inch Shaft
  • We have the Red Line handle, part # 276, that has a 5/16 inch square shaft. It doesn't look as much like your handle as # PLR7011L, and isn't as heavy-duty, but it's the correct size shank and still locks. This is the closest option to your handle that we carry.
    view full answer...

  • How Does Enclosed Trailer Vent Keep Rain Out of Trailer?
  • The enclosed trailer vents we offer are designed to keep the rain out and the best option would be the 2-Piece Side Vent for Enclosed Trailers # 9139. As you can see from the accompanying photo the exterior piece is angled to keep rainwater out and it also has an interior baffle that will direct rainwater to drain holes in the corner of the vent. The butterfly vent also allows you to close it if you'd like. To install this vent you will need 20 screws and four #10/32 machine screws as well...
    view full answer...

  • Availability of Side Vents for Toy Hauler Trailer
  • For trailer side vents we have a couple options but none that are 9 inch by 9 inch. We have the part # 9139 which is 10 by 12 inch and the part # HMAV2-AVT2 which is more of a semi-circle shape that is 6 by 8 inch.
    view full answer...

  • How to Disable Rain Sensor Feature on MaxxAir MaxxFan RV Vent MA00-04500K
  • It sounds like you have the MaxxAir MaxxFan RV Vent with rain sensor # MA00-04500K. This sensor consists of a small circuit board, which is shown in the linked photo. This could have failed, perhaps from damage from an impact from a tree branch or something like that. You can try turning this feature off. On the vent's keypad there is a button that allows you to disable the rain sensor feature. This is noted by an arrow in the second photo.
    view full answer...

  • Installing MaxxFan Plus in New Travel Trailer
  • All you will need to install the MaxxFan Plus # MA00-04500K vent and fan is a standard 14" x 14" opening and roof that is between 2" and 6-1/2" thick. Since your trailer came with a pair of MaxxFans already it is a very good bet your current vents are installed in an opening that size. Though it is not possible to know if the mounting holes will line up as I am unsure of the model number of your current MaxxFans, the MaxxFan Plus does come with the needed garnish (instead of using your...
    view full answer...

  • Replacement Vent Cover for Vent With Continuous Metal Hinge
  • I did look up your order history (thank you!) and found that the last replacement lid you got from us was the Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent - Smoke - Wedge Shape # BVD0449-A03. That said, it looks like you want a replacement lid with a metal continuous hinge and we do carry those, the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents - White # BV0554-01 and Smoke # BV0554-03, either of which will work for you. I've added links to...
    view full answer...

  • Bifold To Single Door Charmc Gooseneck Enclosed Trailer Conversion
  • Depending on your dimensions, the double torsion springs fit 96 inches wide, # CB250D96SHD or the 81 inches wide, # ERS120D81 would be used. Installation requiring winding torsion springs can be very dangerous if you don't have prior experience. A local garage door company can install this system if you're not confident. A retention device for the door when it is up such as # 383200 can also be used horizontally or vertically.
    view full answer...

  • Replacement Trailer Roof Vent and Installation Kit
  • Most RV roof vents are the standard 14 x 14-inch size which is the size that replacement lid # BV0554-03 fits. We can help you with just a new lid if that is all you need and we can also supply a whole new vent assembly if you prefer. If you want to install a complete new 14 x 14 vent you can select one from the page I linked. We have manual vents without fans like # V2092SP-28 and both 12V DC-power vents like # MA00-07500K and 110V AC-power units like # V2128SP-01. At the top of the...
    view full answer...

  • Replacement Circuit Board for MaxxAir Model 4751KSV05 Powered Vent Fan
  • I reached out to my contact at MaxxAir and she said that the correct printed circuit board for your MaxxAir model 4751KSV05 powered vent fan is the part # MA10A04751KS.
    view full answer...

  • Replacement Entry Door Lock for Jayco Part 0089033 on 2002 Pop-Up Camper Trailer
  • Jayco and other RV trailer makers do not maintain details about the smaller items like the locks they install but based on the information I could find on the Jayco part 0089033 that is installed on your trailer, it looks like the closest option we have available is with a paddle handle locking latch like the Polar Hardware # PLR5115. This paddle handle latch measures 5-1/2 inches long and 4-1/4 inches wide. It uses a cutout dimension of 4-5/8 inches long and 3-3/8 inches wide. It features...
    view full answer...

  • Ladder Racks For Trailers and Trailers with Crossbars
  • The Rack'em Fitz-All Enclosed Trailer Ladder Rack # RA-28 has the versatility to fit many of our trailers even though they are not enclosed. The Pack'Em Ladder Rack Bracket Kit for Enclosed Trailers # PK-28B would also work, but the sides are not as sturdy as if there were an enclosed roof frame already in place, so using these systems will have weight limits that aren't accurate for that custom application. I've attached a link to our trailers for you. If you don't specifically...
    view full answer...

  • Hardware Needed to Install MaxxFan Deluxe Roof Vent # MA00-05100K
  • The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat # MA00-05100K referenced in your question includes the white interior trim piece (garnish), insulated electrical connectors and the hardware needed for installation. The only thing you will need to add is some roof sealant # 0160297 and 16 gauge wire like # DW02359-1 if you don't already have it. The wire is sold by the foot so you can get exactly the length you need. This is a really nice roof vent with fan that will move air in...
    view full answer...

  • Comparison of Camco # CAM40453 and MaxxAir # MA00-933069 RV Roof Vent Covers
  • Both roof vent covers, Camco part # CAM40453 and MaxxAir part # MA00-933069, have the same purpose and fit on any standard 14 by 14 inch roof vent. Both of them allow you to keep your vent open during rain without water getting inside your trailer. The Camco is slightly smaller at 18-1/2 by 18 inches compared to the MaxxAir at 19 by 18-1/2 inches. The Camco is also about a 1/2 inch shorter in height measuring 8-1/2 inches versus the MaxxAir at 9 inches. With that being said I prefer...
    view full answer...

  • Replacement Circuit Board Recommendation for MaxxFan Roof Vent that Stopped Working with Remote
  • Sounds like the circuit board of your MaxxFan has gone bad and is in need of being replaced with a new one like the part # MA10A21275K which is the correct replacement for your roof vent.
    view full answer...

  • Cover for a MaxxAir 4500k Roof Vent
  • For the MaxxAir MaxxFan Plus vents you can use the MaxxAir II cover # MA00-933073. It is 22-1/8" long x 20-1/8" wide x 9-3/8" tall.
    view full answer...

  • Replacement Remote for MaxxAir MaxxFan Deluxe 00-07000K
  • Hi, and yes there is a replacement remote for your MaxxAir MaxxFan Deluxe Roof Vent # MA00-07000K. It is available right here: Replacement Handheld Remote for Maxxair # MA00A01150K and you can find the price directly on the product page.
    view full answer...

  • Comparing the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Covers part FVU1400GRS and FVU1500GR
  • The Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover part # FVU1400GRS is designed to be used with Fan-Tastic Vent model numbers starting with "DF" whereas the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover part # FVU1500GR is designed to be used with Fan-Tastic Vent model numbers starting with "FA" or "FV". That is the only difference. The model number will be on the base under the screen.
    view full answer...

  • Troubleshooting MaxxFan Plus Roof Vent
  • According to the manufacturer's instructions three beeps and a green light on the MaxxFan Plus Roof Vent # MA00-04000K indicates you have entered Auto Mode so that all seems normal. However, if the light is on but the fan has stopped working that is most likely a sign that the circuit board has failed and needs to be replaced. For MaxxAir model 4000K you'd want to use Replacement Printed Circuit Board for MaxxAir Manual Lift RV Roof Vents # MA10A21276K.
    view full answer...

  • Replacement Roof Vent Cover for Fan-Tastic K2020-82
  • I spoke to my contact at Fan-Tastic and they informed me that the Replacement Dome for Fan-Tastic Vent RV Roof Vents part # FVK1020-19 is a direct replacment for your "K2020-82" roof vent cover. For a vent cover that will allow for you to open it in the rain you will want to use the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover part # FVU1500BL for black, part # FVU1500WH for white, or part # FVU1500GR for smoke.
    view full answer...

  • Replacement Circuit Board for MaxxFan Roof Vent 5100K
  • For your MaxxFan RV roof vent part # MA00-05100K the correct replacement circuit board is the # MA10A21276K.
    view full answer...

  • How To Add Power Wire for MaxxFan Deluxe Vent with Fan
  • The MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke # MA00-07500K requires 12V power at 5 amp draw. Since you are installing in a location that doesn't have power wires run, you will need to run a power wire like # 12-1-1 or # 10-1-1 (sold by the foot) to your battery or to another 12V power source that can handle that draw. There is a good chance the bathroom fan or a light could be a good tie in point as long as you tie in prior to a switch. You...
    view full answer...

  • Is Butyl Tape Needed When Installing MaxFan Roof Vent
  • When installing the MaxxFan Roof Vent # MA00A04301K that you referenced you will want to use butyl tape on the vent edges in addition to the sealant that you will apply around the unit to cover up bolt holes and any other areas that might lead to a leak. I have attached a sample vent installation on a different model vent just so you can get a better idea of the process. We do have the Roof Vent Installation Kit # 344270KITW available that includes a 10.1 oz bottle of sealant, a 60...
    view full answer...

  • Which MaxxFan Deluxe Fan Lens Color Lets in Least Amount of Light
  • The smoke cover let's in more light than the solid white since the smoke is a translucent color designed to allow light to pass through. So for that you'd want the part # MA00-07000K and you'd be set.
    view full answer...

  • Recommended Replacement Vent With Integrated Fan to Replace Broken Fan Motor
  • We unfortunately do not carry that older style motor. Fantastic Vent has upgraded all their fan assemblies to the newer style bow-tie mount fan # FVK8017-00 like is available in the # FV801200 vent with fan. I recommend this replacement or a similar vent upgrade to give you the working fan. I've linked a video to assist.
    view full answer...

  • How to Acquire Three Rackem Ladder Rack Part # RA-28 Crossbars
  • In order to receive three crossbars you would need to purchase two sets of the Rack'em Fitz-All Enclosed Trailer Ladder Rack part # RA-28. We also have the Pack'Em Ladder Rack Bracket Kit for Enclosed Trailers part # PK-28B which will allow you to create your own ladder rack with 2x4's but you would also need to purchase two sets in order to receive three crossbars. This option will however be more economical if that is of a concern to you. I have attached an install and review video...
    view full answer...

  • Troubleshooting Maxxair Deluxe Fan That Starts and then Quits, Closes and Beeps Constantly
  • It sounds like a circuit board issue. I recommend the Replacement Printed Circuit Board for MaxxAir Manual Lift RV Roof Vents # MA10A21275K if you have a 4500K, 7000K, or 7500K model. If your model is a 4000K, 5100K, or 6200K then Replacement Printed Circuit Board for MaxxAir Manual Lift RV Roof Vents # MA10A21276K is what you need.
    view full answer...

  • How to Determine Correct Vent Cover or Replacement Lid for Cargo Trailer
  • We have vent covers which will work for you although there is no type of database available with specific parts for each year, make and model of trailer; due to this you just need to take a look at your vent to find out which cover will work for you. The standard roof vent measures 14-1/4" x 14-1/4" so if you measure yours it is likely to be that and you can use the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover # FVU1500WH (White) or # FVU1500BL (Black). If you were instead asking...
    view full answer...

  • Recommended Fan-Tastic Vent Roof Vent With Fan For Quiet Operation
  • For your vent with fan I recommend the Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote - Powered Lift # FV807350. This fan has 13 speeds and has the ability to use the thermostat to conserve energy and automatically adjust for your needs. It also has a rain senor to close the dome when the sensor gets wet and resume when the sensor is dry. I've attached a video to assist. For a more economical option we have # FV802250 which has a manual lift vent and a fan with 3 speeds. This also...
    view full answer...

  • Can the MaxxAir MaxxFan # MA00-06200K be Connected to Switch on Wall
  • The MaxxAir MaxxFan # MA00-06200K that you referenced is equivalent to a base model of the MaxxFan and it is only controlled by a keypad on the vent itself. If you wanted to connect it to your existing wiring then you would have to do some modification which is not recommended. Instead I recommend going with the MaxxFan Deluxe # MA00-07500K which is the upgraded version. It has the same 10-speed settings but it comes with a remote and remote holder. You can mount the remote holder to...
    view full answer...

  • Side and Roof Vent Options for 5 x 8 Enclosed Trailer
  • We carry all sorts of trailer vents and we can help you with a solution to provide proper ventilation in your 5 x 8 trailer. You can use either a roof vent or a side-mount ventilator, or both if you wish. We offer two side-mount ventilators that offer passive air flow, parts # PLR1715 and # PLR20. Side Cowl Ventilator # PLR1715 includes a screen and measures approximately 6 x 11-inches. Ventilator # PLR20 measures approximately 10-1/2 x 12-inches. Both vents allow you to open/close air...
    view full answer...

  • Replacement Vent Cover For 16 Foot Wells Cargo Trailer
  • It looks like you have a standard 14-1/4 by 14-1/4 trailer roof vent but you would want to measure to be sure. The second step is to look at the hinge portion of your cover. It looks like you may have a metal continuous hinge but I have added examples for you to be sure. I recommend Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents part # BV0554-01 for a metal continuous hinge. I have added an installation video for your reference.
    view full answer...

  • Flush Mount Door Latch for Cargo Trailer Side Door
  • Thank you for the detailed photo, it was a great help. The latches are actually not designed to fit the thickness of the door so you could use whichever size would allow the pin to catch in the door lip. f you were able to make it so the door did not have a gap, then you could use a door latch such as the Paneloc Slam Latch # F708-204P011, which is 2" long x 1-5/8" wide with a mounting hole diameter of 3/16" and a pin width of 7/16". A different option would be the Paneloc Slam Latch #...
    view full answer...

  • Does Fan-Tastic Vent Upgrade Assembly 7350 Fit Fan-Tastic 1200 Series Vent
  • I have some good news for your wallet because I reached out to the manufacturer, Dometic, who told me you can upgrade your 1200 Series Fan-Tastic Vent Roof Vent # FV801200 with the Fan-Tastic Vent Roof Vent Assembly Upgrade Kit # FV807357 to get the same motorized assembly with remote that you would get with a whole new vent. In regards to the covers, the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover # FVU1500WH (White) or # FVU1500BL (Black) are going to fit on top of your Airstream....
    view full answer...

  • How to Carry Canoe on 2004 Ford F-150 Towing Coachmen Trailer Trailer
  • Most of the Coachmen Apex travel trailers shown on their website include several common rooftop features like antennas, air conditioners, ducts and vents. The AC units tend to be fairly tall, most about 12- to 15-inches, and racks made for trailer roofs, like # RA-28, are not tall enough to clear these. Apart from that you have the matter of getting the canoe about 9 or 10 feet in the air! I can suggest a better option; using a front hitch on your 2004 F-150 along with a load support...
    view full answer...

  • MaxxFan 2016 Keystone Montana Model 3710FL Won't Stop Running
  • If your MaxxFan with the rain sensor, like part # MA00-04500K, starts operating automatically and the controller or the controls on the unit aren't working then that sounds like a bad circuit board or that the built-in safety feature for too much (or not enough) voltage was activated and the circuit board locked up. Since you already removed power from the vent try connecting it back to power. If it works properly then it was just locked up and needed to be disconnected from power to unlock...
    view full answer...

  • Recommended Wall Vents and Roof Vent for Enclosed Trailer Air Movement
  • The Multi-Purpose Ventilator - Aluminum # PLR20 will work to help you move air through your trailer. You may also be interested in the Side Cowl Ventilator with Screen # PLR1715. For the best air movement and still the weather protection, I recommend these side vents for the lower vents and then using a roof vent like # MA00-06401K if you have a trailer battery. If not, then I recommend the Ultra-Fab Solar-Powered Plumbing Vent for Motor Homes - 7" Diameter x 3-3/4" Tall # UF53-945001...
    view full answer...

  • Cam Style Trailer Door Latch Recommendation For Limited Clearance Area for Brackets
  • The big difference between the Cam Door Latch # PLR458-018 and the # PLR658-002 is the robustness of the pipe mount on the handle side. The # PLR658-002 is more for heavy duty applications and comes with bushings for the pipe to mount in. This requires a 1-5/16 inch diameter pipe and the other requires 3/4 inch diameter. That said, since you said you only have a space of 2-7/16 inches for the bottom bracket to fit you'd actually want the part # PLR258-002 instead as it has a smaller...
    view full answer...

  • Picking Out Replacement Roof Vent Lid for Ventline: AS-13 M VA446-1
  • Thank you for providing the replacement vent lid part number VA530. This was indeed once a valid part that is now obsolete, but we can still help you select a replacement vent lid. Please refer to the linked photo showing the different hinge styles on the replacement lids we offer. We have 3-point, 4-point and continuous hinge type replacement lids. Just match up your hinge type and then on the linked page click on the filters to choose your hinge type and preferred lid color. For...
    view full answer...

  • Can Maxxair Roof Vent Cover Fit on Fan-Tastic Roof Vent # FV801208
  • Yes, the MaxxAir Standard RV Vent Cover part # MA00-933069 will fit if you have the Fan-Tastic Vent Roof Vent w/ 12V Fan # FV801208 installed. This cover is very universal in design and basically fits all standard 14 inch roof vents like the part # FV801208.
    view full answer...

  • What is the Most UV Resistant Roof Vent Cover Material
  • There are three types of materials used in the construction of most roof vent covers which are metal, polypropylene, and polycarbonate. The metal option will be the most UV resistant followed by polycarbonate and polypropylene in that order. For a metal replacement roof vent cover that has a continuous hinge and 14-1/4"x14-1/4" opening, I recommend part # BV0534-00. For a polycarbonate replacement roof vent cover that has a continuous hinge and 14-1/4"x14-1/4" opening, I recommend part...
    view full answer...

  • Is Camco Vent Cover Compatible with Fan-Tastic Vent Fan?
  • The Camco RV and Enclosed Trailer Roof Vent Cover # CAM40453 is compatible with all standard size roof vents including the Fan-Tastic vent fans like # FV801250. I've attached a video of the installation to assist.
    view full answer...

  • Recommended MaxxAir MaxxFan Plus Vent Cover
  • For your MaxxFan Plus Roof Vent w/ 12V Fan, Thermostat, and Remote # MA00-04500K, the MaxxAir FanMate Rain Cover is your best fit for fully functionality. These come in 3 colors: Smoke # MA00-955003 White # MA00-955001 Black # MA00-955002 This will allow your vent to fully open and not come in contact with the cover as they are designed for compatibility.
    view full answer...

  • Recommended Gate/Ramp Assist and Hinge for Trailer Build
  • The 2K Torque Ramp Spring # RS16933RH is an industrial strength spring. It is designed for up to 90 degrees of deflection, but most people by hand can cause no deflection at all. It is designed to be used with the LH # RS16933LH, and is for heavy ramps or doors like in the attached photo. I would assume it is too strong for your application based on your wording. You may want to consider a different style spring like the Enclosed Trailer Ramp Spring - Dual Spring, 81" Wide # ERS120D81...
    view full answer...

  • Difference Between Fan-Tastic Trailer Roof Vent Covers
  • I believe you were referencing the Fan-Tastic Trailer Roof Vent Covers, though there isn't a 1600 model I was able to reference. There are 1400 and 1500 models, and the difference between them is just what they fit. The Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover # FVU1400GRS fits all Fan-Tastic Vent trailer roof vents with model numbers starting with "DF" while Vent Cover # FVU1500GR fits all Fan-Tastic Vent trailer roof vents with model number starting with "FA" or "FV". The...
    view full answer...

  • Replacement Dome for Fan-Tastic Vent Model 6000A or 6000BTA
  • By "slider track" I believe you are referencing the hinge; if you take a look at the accompanying photo you should be able to see what I am talking about. That should be what your Fan-Tastic vent has and since your model 6000A/6000BTA will measure the standard 14" x 14" there are two replacement domes available, the Replacement Dome for Fan-Tastic Vent RV Roof Vents - Tinted # FVK1020-19 or White # FVK1020-81.
    view full answer...

  • Dimensions of Cam-Action Lockable Door Latch for Large Enclosed Trailers
  • The Cam-Action Lockable Door Latch Kit for Large Enclosed Trailers - Stainless Steel # PLR258-002-SS has the following dimensions as I measured them in our warehouse: Hasp dimensions are 5-1/8" tall x 2" wide 3-3/4" From center of hole to center of hole Lock hole diameter: 1/2" Retainer dimensions: 4-1/2 tall x 1-1/2" wide Measures 3-1/8" from center of hole to center of hole Handle length: 14" Mounting hole diameter: 13/32" Keeper dimensions: 5-1/8" long x -1-1/2" wide Measures...
    view full answer...

  • Can Custom Holes be Drilled Into a Redline Pre-Drilled Round Rubber Bumper
  • Since the Redline Pre-Drilled Round Bumpers, part # D3-96, part # D2-96, and part # D4-96, are made of rubber I see no reason why you cannot drill out mounting holes so that they are custom to your hole patterns. If you will be using the full 96 inches of the bumpers then you may want to consider drilling more mounting holes in your trailer so that the bumper has more support. I recommend drilling out holes to match the rest of the pre-drilled holes to avoid more drilling. Keep in mind...
    view full answer...