Filter Questions and Answers:

reset filter

Expert Answers about Camper Jacks


  • Dimensions of Reese and Ultra-Fab Fifth Wheel Landing Gear
  • I would be happy to help you with those dimensions. The Reese Electric 5th Wheel Landing Gear # RP500708 has the standard weld stop measurements that are 15-1/2" from inside to inside of weld stops and 17-1/2" from outside to outside. The Ultra-Fab # UF17-943010 has weld stop brackets which measure 20-1/4" from outside to outside; it is 8-1/2" from the top of the motor to the first weld point. I have added photos showing the dimensions of these jacks for you to check out. Apart...
    view full answer...

  • Replacement Control Panel for Leveling System on 1995 Fleetwood Motorhome
  • We had another customer with a '94 Bounder in need of the same control panel for their Lippert Power Gear leveling system and Lippert was able to confirm that kit # LC359259 would work. I shared your photo with my tech contact there and he confirmed the item referenced above will work for you.
    view full answer...

  • How to Determine Middle Jack Placement of Lippert Ground Control 3.0
  • I spoke with a representative of Lippert concerning the installation of the middle jacks on your Lippert Ground Control 3.0 - 6-Point Set # LC675817 and was told that there is not a set distance. What you will need to do is run a string line like in the directions (see accompanying photo) and the middle jacks when retracted must be above that line. So depending on the measurement of that string it might be possible for you to mount the middle jacks 48 inches forward. I also asked about...
    view full answer...

  • Dimensions of I Beam Bracket for Lippert Ground Control Leveling System
  • I attached a dimension picture I got from Lippert for the Replacement I-Beam Jack Bracket # LC349975 that you referenced.
    view full answer...

  • Recommended Electric A-Frame Trailer Jack for 2011 Open Range Journeyer 340FLR
  • Tongue jacks are often rated higher than the weight of the trailer tongue they will be supporting. For tongue jack to meet your needs, I recommend the etrailer.com Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black # EJ-3520-BBX. This jack will mount to the same location on your trailer tongue A-frame and will give you a drop leg as well as a really nice LED light on a separate switch to help with connecting or disconnecting. If you want what I consider to be the best...
    view full answer...

  • Leveling System Compatible with 42 Foot 5th Wheel Trailer
  • The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w/ Touchpad and Remote - 20,000 lbs # LC358590 is designed for trailers where the measurement from the front landing gear to the rear is 20 feet or less. If longer, then the manufacturer recommends the 6 point system # LC675817 which adds two middle legs. They always navigate to the safe side, because they rate the 4 point system as 20k capacity based on each individual jack rated for 5K capacity. We do not carry...
    view full answer...

  • Replacement Follow Landing Gear Leg for 1998 Fleetwood Savanna 5th Wheel
  • I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the bevel gear inside your jack leg is the only one that is damaged then you can just obtain the Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060. However, if you don't want to mess with repairing your old jack leg or...
    view full answer...

  • Installation of etrailer Landing Gear
  • The Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs # RVLG-8HDL will simply mount to the weld-on brackets by being bolted on. While an online copy of the manual is not available for this specific landing gear, I did cut out a portion of the Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs # LG-183708 so you can take a look. In regards to the brackets you asked about, the Replacement Weld-On 5th Wheel Landing Gear Leg Bracket # LC113511 will work with...
    view full answer...

  • Recommended Replacement Landing Gear for 2007 Pilgrim 40 Foot 5th Wheel Trailer
  • On your 2007 Pilgrim 40 foot 5th wheel trailer, I recommend using the Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs # UF17-943010. This landing gear will allow you to adjust independently for easy and quick leveling. The leg will travel 1 inch every 15 seconds and has drop legs for even faster compatibility. I've attached a diagram for you to see the connection points based on the weld stops so you can determine if it will bolt right in or if modifications to your...
    view full answer...

  • How to Determine if Lippert High-Speed Power Stabilizer Jack Will Fit Forest River Evo 2550
  • I can tell you exactly what you need to know to find out if the the Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707 will fit your Forest River EVO 2550, though these jacks aren't designed to fit any specific trailer. All you need to do is measure the mounting holes for a stabilizer jack on your trailer, and if they are 68-11/16" from center-hole to center-hole then the Lippert jack will fit! Another option is the Ultra-Fab Power...
    view full answer...

  • Determining Correct Lippert Ground Control System for 2006 Heartland Bighorn 5th Wheel Trailer
  • Installing the Lippert Ground Control System on your 2006 Heartland Bighorn 5th Wheel Trailer is a great idea. When determining whether to use the 4-Point Set # LC358590 or the 6-Point Set # LC675817 there are a couple things you will want to look at specific to your Bighorn Trailer. First is the GVWR of the trailer, which is the most it can weigh when fully loaded. If the GVWR is more than 15,500 pounds, then you will want to go with the 6-Point System. If it is less than 15,500 pounds,...
    view full answer...

  • Is Lippert Ground Control 2.0 System Compatible with 3.0 Motor and Leg?
  • The Lippert 2.0 system is not compatible with the motors on the 3.0 system. The 3.0 system uses electric motors that utilize the hall effect where the 2.0 system does not. This is a completely different design which makes the motor and legs incompatible with the controller and wiring of the 2.0 system. You will need to upgrade your system if you desire that style as your system has been replaced. For the 2.0 system we have the Replacement Heavy-Duty Landing Gear Jack Leg for Ground...
    view full answer...

  • Differences Between the Lippert Components Power Stabilizer Trailer Jacks
  • You made a great choice in the Lippert Components Power Stabilizer Trailer Jack. For starters, all of the jacks measure to be 70-1/2" long with a 3,500 lb weight capacity and have a 30" lift. The difference between them is in regards to what is included with them. The part # LC369774 comes with a white switch and part # LC298707 comes with a black switch. That is the only difference.
    view full answer...

  • Best Landing Gear Upgrade Options for 5th Wheel Trailer
  • We do have motors that you can add to your landing gear. For example, the Landing Gear Set # RVLG-8000 can be operated with the manual crank # RVLG-HDL but you can also add the motor # LC142178 and switch # LG-145236 for effortless operation on your end. The next upgrade for landing gear is the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. This is rated for up to 12,000 lbs and operates via separate motors so you can easily level your 5th wheel trailer without using blocks...
    view full answer...

  • Can Ultra-Fab Ultra Scissor Jacks Be Used without Leveling Blocks
  • The # UF48-979002 feature oversized footplates that are 4-1/2" wide by 9" long, so you could use them without leveling blocks. However, it's not uncommon for people to use leveling blocks like # A10-0918 or even wooden blocks under these jacks to provide extra stability (see photos). This is especially helpful in soft surfaces like grass or dirt. What you do want to make sure is that you chock your wheels to prevent your travel trailer from rocking and rolling when parked. For that,...
    view full answer...

  • Replacement Landing Gear for 2004 Dutchman Sport 30 Travel Trailer
  • Landing gear is designed to stabilize a portion of your trailer's weight, not to support the full GVWR of your trailer. From what I found online, your 2004 Dutchman Sport 30 has a GVWR of 9,764 lbs, so a set of 8,000 lb landing gear (combined) would be more than enough to support the front of your 5th wheel trailer. The Bulldog Tandem Landing Gear Set # BD500162, you were looking at, would work as a replacement. There are just bolts already installed where you'll mount your existing...
    view full answer...

  • Replacement Front Jack Leg for Lippert Ground Control 3.0 Leveling System LC358590
  • Based on your troubleshooting efforts my contact at Lippert thinks there may be a bend in the right front jack leg of your Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590. Since the jack struggles with motor power but works when you manually crank it he thinks a damaged leg is the issue. You can use Replacement Lead Leg # LC362485 which works with your Ground Control # LC358590.
    view full answer...

  • Atwood Landing Gear Replacement for 36 Long Landing Gear
  • To replace the Atwood landing gear on your 5th wheel trailer you will need to measure the distance between your weld stops. This is typically 15-1/2" on the inside and 17-1/2" on the outside (see attached photo). We do have replacement options but since Atwood is no longer in the landing gear business you need to replace your whole landing gear set to ensure that the gear ratio and strengths are the same. If your weld stop locations match the picture then I recommend using the 8,000...
    view full answer...

  • Recommended Replacement Landing Jack System for 2008 Keystone Montana Mountaineer 345DBQ
  • For your 2008 Keystone Montana Mountaneer 345DBQ, the Lippert Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear # LC178653 and follow leg # LC178652 are a perfect replacement. These parts are exactly what you need for your trailer. If you want the entire replacement kit, you can use the Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs # LC333966 or electric # LC333964 which will have only one option of weld stops for your trailer. I've...
    view full answer...

  • Is There a Way to Replace Cracked Screen on Lippert Smart Jack
  • The only way to get a new control panel would be to replace your entire Smart Jack with part # LC643589. I reached out to my contact at Lippert who confirmed that the only replacement parts for the jack includes hardware like the pin or the footplate. With this being the case your best option to protect the buttons is a trailer jack cover like part # UF38-944020. If you'd rather use a different jack then I recommend the Husky Brute Electric Trailer Jack # HT87247 because it is rated...
    view full answer...

  • Replacement Motor for Lippert High-Speed Power Stabilizer Jack
  • To replace the motor on your Lippert High-Speed Power Stabilizer Jack # LC298707, you will just need the Lippert Stabilizer Jack Motor # LC352338. This is a direct replacement on your stabilizer jack and it will install just like the existing unit on the system.
    view full answer...

  • How To Install the Landing Gear Set Part # RVLG-8000
  • The installation of the Landing Gear Set part # RVLG-8000 will be fairly straight forward. Basically, you will need to have a metal support structure so you can attach welded tabs part # LC113511 to it, 15-1/2" apart. Once these are installed you can then mount the jack tube and modify a cross-shaft that connects the two together which is included. Then, you will need to obtain a handle, the Crank Handle part # RVLG-HDL to raise and lower the legs. Unfortunately, we do not have a video...
    view full answer...

  • How to Manually Operate the Ultra-Fab Deluxe Electric Landing Gear Set
  • Good question; if for some reason there is an issue with the power or motor, you can manually operate the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. I took a look at the instructions, and the accompanying cut out from them explains what you'll need to do. There are four screws that hold the motor and gear assembly on, and you'll need to remove those and turn the slotted shaft with a flathead screwdriver. Then, if ever need be you can get a replacement motor with the...
    view full answer...

  • Are Replacement Legs Available for the Lippert High-Speed Power Stabilizer Jack # LC298707
  • We do have the replacement Stabilizer Jack Support Arm # LC1134122 which is the yellow brackets for your High-Speed Power Stabilizer Jack # LC298707, but if you are looking for replacement legs you will have to replace the whole jack. I confirmed with my contact at Lippert that there are no replacement legs for their stabilizer jacks.
    view full answer...

  • Do Camco FasTen Leveling RV Blocks Have Weight Capacity
  • I confirmed with Camco that their FasTen RV Leveling Blocks # CAM44521 do not carry a maximum RV weight rating so they are compatible with virtually any RV or motorhome out there. This set is gray and the part # CAM44512 is yellow.
    view full answer...

  • 4-Point Ground Control or 6-Point Ground Control for 2018 Keystone Cougar 338RLK?
  • I have added a photo of the manual from the Ground Control unit which will explain which of the systems, the 4-Point # LC358590 or 6-Point # LC675817 you need to use. From my research it looks like your 2018 Keystone Cougar 338RLK has a 12,490 lb GVWR so unless the center of the landing gear foot and the center of the rear jack foot is 20 feet or greater it is not recommended to use the 6-Point system.
    view full answer...

  • Replacement Drop Leg Extension for Lippert Power Jack with Additional Height Needed
  • The Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black # LC285318 has a drop leg available that will give an extra 4-1/2 inches with # LC405217.
    view full answer...

  • Installation of JT Strong Arm Stabilizer Kit for Electric Stabilizer Jacks on Camping Trailer
  • The JT's Strong Arm Jack Stabilizer Kit for Travel Trailers # LC191025 can be used with the Electric Stabilizer Jack Pad Adapter for JT's Strong Arm Jack Stabilizer Kits - Qty 4 # LC314597 and each kit will work on two stabilizer jacks. I've attached a picture to further assist. For your 4 jacks, you will need 2 kits.
    view full answer...

  • Electric Tongue Jack for Straight Pole Tongue Recommendation
  • The only electric power jack we have for the pole tongue is the Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs # F141401. This jack will allow up to 22 inches of lift using the 8 inch drop leg and 14 inches of screw travel and will fit 3 to 5 inch tall frames. The only way to use a caster wheel on this jack is to remove the drop leg and use a caster wheel like the Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks # PS1400750340. The...
    view full answer...

  • Replacement Scissor Jack for a 2017 Rpod 179 Hood River Edition
  • While I do not know which specific jack make and model came on your Rpod originally you can install pretty much any other similar jack, such as Ram Scissor Stabilizer Jack # TJSC-24, as a replacement. The mounting holes likely will not perfectly line up but it wouldn't take much effort to add a new hole or two to properly install the jack. Since the original was also welded I do recommend doing the same with the new jack. Any welding should be done by a professional welder.
    view full answer...

  • Replacement Cap for RAM Electric A-Frame Trailer Jack
  • For the replacement cap that will cover the manual override on your Electric A-Frame Jack # EJ-3520-BBX, you will just need the Replacement Cap # EJ-3520-BCP. This will include one cap for your jack.
    view full answer...

  • Replacement Foot Pads for Lippert Ground Control 3.0
  • The replacement foot pads for the Lippert Ground Control 3.0 # LC675817 (6-Point Set) or # LC358590 (4-Point Set) are different; the Replacement Rear Foot Pad # LC377962 has a circular receiver tube and the Replacement Front Foot Pad # LC362486 has a square receiver tube. Since you have the 6-point system and said you lost the left middle I believe you need the Front Foot Pad # LC362486.
    view full answer...

  • Replacement Landing Gear for a Keystone Laredo 5th Wheel Trailer
  • Bulldog Tandem Landing Gear Set # BD500162 is a great option for a manual set to replace the landing gear on your Keystone Laredo. I have linked a video review for you. The handle is not included so use # BD500203 to add the crank handle. For an electric set you could use # RVLG-8HDL and add motor # LC142178 and, if you don't already have one, a switch # LC145236.
    view full answer...

  • Dual Jack Landing Gear for Gooseneck Trailer Transporting Large Water Tank
  • The weight of 1600 gallons of water, without the water tank's own weight factored in, is about 13,350-lbs. For such a high-weight application I suggest Bulldog Square Jacks # BD182804 and # BD182805 along with Connecting Rod # BDCS730300. Two jacks are definitely the way to go. If you wish to motorize this jack setup you can also add motor kit # BD1824200100. I also recommend you first determine the actual pin weight of the loaded trailer so that you can be sure to select jacks with...
    view full answer...

  • What Size Pipe Mount Does the Bulldog Square Jack w/ Round Pipe Mount BD182524 Use
  • The Bulldog Square Jack w/ Round Pipe Mount part # BD182524 is designed to be used with the Bulldog Weld-On Jack Pipe Mount part # BD005122 which is 4" diameter with a 7/8" pin hole. I don't know of any jacks off-hand which match your pipe mount so you are going to be much better off just having a new pipe mount welded on. The distance from the center of the mount to the bottom of the footplate is 17" while retracted and 29.6" while extended.
    view full answer...

  • Comparing the Stromberg Carlson Trailer Jacks # JET-5000NG VS JET-5000
  • All-around the Stromberg Carlson Electric Trailer Jack # JET-5000NG is nicer than the # JET-5000. The bearings in the part # JET-5000NG allow it to raise and lower much smoother and quicker, the size of the head is a bit smaller and the lighting is nicer too. For how similar the price is between the two the # JET-5000NG really is the winner.
    view full answer...

  • Can Power for the Bulldog Powered Drive Trailer Jack Come from the 7-Way Trailer Connector
  • The installation of a 7-way trailer plug like the Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector part # PK12706 on an electric a-frame trailer jack like the Bulldog Powered Drive Trailer Jack part # BD500200 is not something that we have the ability to offer you unfortunately. However, this process will be extremely simple as all you need to do is insert the power wire on the jack into the correct terminal on the 7-way and then tighter down the screw. It should not take more than...
    view full answer...

  • Recommendation For Replacement Legs That Are Compatible With Lippert Ground Control 3.0 System
  • The Lippert Ground Control 3.0 system, Item # LC358590, has uniquely designed legs that work together and so the Atwood legs would not work. I recommend buying the whole system together and then buying the specific replacement legs for the system as needed. The Replacement Lead Leg is Item # LC305340 and the Replacement Rear Leg is Item # LC342610. I have attached additional information and a video for you to check out.
    view full answer...

  • How to Pick Out Landing Gear Replacement for 2003 Nomad Scout FW Model 237
  • In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the #...
    view full answer...

  • What Are the Proper Maintenance Procedures for the Lippert Ground Control 3.0 System
  • I have attached for you below the recommend preventive maintenance steps for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling Systems like part # LC358590. 1. For optimum performance, the system requires full battery current and voltage. The battery must be maintained at full capacity. 2. Check the terminals and other connections at the battery, the controller, and the jacks for corrosion, and loose or damaged connections. 3. Remove dirt and road debris from jacks as needed. 4....
    view full answer...

  • Can a Breakaway Battery be Used to Power an Electric A-Frame Trailer Jack
  • If your breakaway system is powered by its own battery then it is likely a 5 amp hour battery which is not high enough to power an electric trailer jack, such as # BD500199, since they can draw about 30 amps under load. The other issue is that a breakaway system needs its own dedicated battery and should not be shared by other 12 volt accessories. If your trailer has a 7-Way trailer connector with functioning 12 volt circuit you could use electric jack # 3370093500 which plugs into a...
    view full answer...

  • JTs Strong Arm Stabilizer Recommend for 2019 Keystone Montana 385BR with Ground Control
  • Yes, the JT Strong Arm Stabilizer System # LC191023 will work with your LCI Level Up System. I checked with Lippert and found that you can use the JT's Strong Arm Jack Stabilizer Kit # LC191023 with the adapter lugs # LC314592. For your LCI level up system will need a quantity of 6 adapter lugs, these are sold as a quantity of 2 on our site.
    view full answer...

  • Types of Jacks Suitable to Stabilize Equipment Trailer During Loading
  • We have various jack and stabilizer products that you can consider for addition to the rear of your equipment trailer to support it during loading processes. I linked our main page for such items so you can see all we offer. If you want a low-cost and lightweight option that does not require permanent installation you might look at the Ultra-Fab Stackable Stabilizers # UF48-979003 (a set of 2) or the 4-piece set # UF48-979004. These offer 17-inches of lift and the 4-piece set weighs...
    view full answer...

  • Can the Jacks on a 2019 Keystone Cougar 34TSB Be Converted To Ground Control Auto Level
  • In order to add the auto leveling feature to your 2019 Keystone Cougar 34TSB you would need to purchase the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System part # LC672136 which is an entire system that comes with jacks, control module, wiring, and hardware. The reason you cannot convert what you have to the Electric Ground Control TT is because the jacks you have are not correct for the kit. The jacks you have on your trailer are actually not jacks at all...
    view full answer...

  • Wiring Electric Jack to Plug Into 7-Way on Tow Vehicle
  • Although wiring an electric jack like the etrailer.com # EJ-3520-BBX you referenced to a dedicated battery on the trailer is the preferred solution for ensuring you get the needed power, you can indeed wire it to a 7-Way plug like # A7WCB for it to be connected to the 7-Way on your truck when needed. If you don't yet have an electric jack, we actually have a 3,500 pound unit available with the Buyers Products # 3370093500 that is designed to be used this way right out of the box. This...
    view full answer...

  • Replacement Manual Override Crank and Brake Release for Husky Brute Electric Jack
  • He/She will want the Replacement Manual Override Crank w/Brake Release Handle for Husky Brute Jacks - 7/16" Hex Head # 87639. I've attached a photo to assist as well as a video.
    view full answer...

  • Can I Use Fastway ONEstep Wheel Chocks On My Triple Axle Trailer
  • Yes, you can use Fastway ONEstep Wheel Chocks for Tandem-Axle Trailers and RVs part # FA84-00-4840 on your triple axle trailer. You would need 2 sets. The chocks adjust from 16" to 24". You do want to make sure the wheel spacing between the tires is between 16" and 24". To determine this measure on the ground from the contact point to the other contact point of each tire. I have attached a photo for your reference. If your wheel spacing is 24-30" you need Fastway ONEstep XL Wheel Chocks...
    view full answer...

  • Recommended Flatbed Cargo Trailer Stabilizer Leg for Rear of Trailer
  • For your Sure Trac ST9614 HLODOD-B-140 trailer I recommend adding the Ultra-Fab Ultra Scissor Jacks - 24" Lift - 6,500 lbs - Qty 2 # UF48-979002. I believe these will work well to stabilize your trailer for loading. They can be adjusted using the hand crank or you can use the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005 if you prefer. If you want more of a solid mount drop leg stabilizer that you would weld on, we have the Square Drop Leg Stabilizer Jack...
    view full answer...

  • Troubleshooting Ultra-Fab Phoenix Electric Tongue Jack That Won't Extend or Retract
  • The Ultra-Fab Phoenix Electric Trailer Jack with Remote- 5,500 lbs # UF38-944055 or 4,000 lb # UF38-944040 without remote sounds like it may have a mechanical issue. I recommend using the manual crank to extend or lower the jack. If you can use this, then you isolate the issue to electrical with a possible bad ground or motor issue. If you can't physically move the jack with the manual crank then we know the issue is mechanical with the inner rod seized or having stripped threads. If...
    view full answer...

  • Difference Between Bulldog Velocity Series Electric Landing Gear Jacks
  • The only difference is that one of the Bulldog Velocity Series Electric Landing Gear Jacks comes with the Remote Control for Bulldog Velocity Series Electric Landing Gear Jack # BD500372 while the other does not: - With Remote Control: Bulldog Velocity Series Electric Landing Gear Jack # BD185400 - Without Remote Control: Bulldog Velocity Series Electric Landing Gear Jack # BD185402 Otherwise, both have a 12,000 lb capacity and are very fast jacks, lifting 20 inches in 60 seconds....
    view full answer...

  • Replacement Parts for the Bulldog Powered Drive Trailer Jack part BD500199
  • I have attached for you a list of the replacement parts that are available for the Bulldog Powered Drive Trailer Jack part # BD500199. I am not sure which part in particular that you are referring to but if it is not listed below then you would unfortunately have to replace the jack. The Ultra-Fab Electric A-Frame Jack part # UF38-944014 would be a good cost effective replacement for this if needed. Replacement Extend and Retract Switch part # BD500363 Replacement Manual Override Crank...
    view full answer...

  • Jack for Tire Replacement on Lifted Jeep
  • Our scissor jacks should not be used to lift a car to replace a spare tire as they were not designed for that application. Instead, depending on how far you need to lift, you may be able to use the Powerbuilt Unijack # ALL620470, which can lift up to 4,000 lbs and a range between 8-5/8" and 18-3/8", or Powerbuilt Unijack # ALL620471 which has a lift capacity of 6,000 lbs and a lift range between 11" and 21". After lifting your vehicle the jack locks into place with a safety bar so you would...
    view full answer...

  • Can JT's Strong Arm Jack Stabilizer Kit be Used on Round Hydraulic Landing Gear Jacks
  • Yes, the JT's Strong Arm Jack Stabilizer Kit # LC191023 referenced in your question can be used with hydraulic round jacks like what you have on your 2018 Grand Design as long as you add the Hydraulic Jack Adapter Lugs # LC314592. These adapter lugs can be welded or bolted onto the foot pads of your landing gear to allow the JT's Strong Arm stabilizers to attach to the jacks. The Strong Arm Kit you referenced is designed for trailers that have 58 inches or more between the front landing...
    view full answer...

  • Recommended Stabilizing Kit for Lippert Auto Leveling System on 2017 Keystone Sprinter 5th Wheel
  • The auto leveling system on your 2017 Keystone Sprinter is a Lippert auto leveling system, so the stabilizers that I recommend are the JT's Strong Arm Jack Stabilizer Kit which are also by Lippert and confirmed to work. If you have more than 58 inches between your front landing gear legs, then you will want part # LC191023. If you have less than 58 inches, then you will want part # LC191024. You will also need the Adapter Lug, # LC314592, for the rear leveling legs.
    view full answer...

  • Can etrailer EJ3527-BBX Trailer Jack Be Powered From 7-Way Trailer Connector on 2020 Ford F-150
  • The etrailer brand # EJ3527-BBX is equipped with a 7-way plug that can be plugged into the 7-way trailer connector on your 2020 Ford F-150. This being said, for more reliable operation, it's best to install a battery on the trailer and run a powered jack from that. The etrailer # EJ-3520-BBX jack is designed to be wired directly to a trailer mounted battery. You can wire the 12-volt feed from the 7-way to the trailer mounted battery. It won't charge the battery completely if it gets...
    view full answer...

  • Fuse Location on etrailer.com Electric Jack # EJ-3520-BBX
  • On the etrailer.com Electric Jack w/ Footplate # EJ-3520-BBX that you referenced the 30 amp barrel fuse like # EJ-FUSE is located in a flared opening right where the black power wire comes out of the motor housing. It is very easy to access and replace if the need arises. I have attached a short video demonstration on this jack that you can check out as well.
    view full answer...

  • Mounting Plate Height of Replacement I-Beam Jack Bracket for Lippert Ground Control
  • The overall height of the mounting plate of the Replacement I-Beam Jack Bracket for Lippert Ground Control # LC349975 is 13 inches.
    view full answer...

  • How to Charge a Trailer Battery for Use with a Bulldog Jack
  • What you described is actually the best solution! Connecting your battery to 12V Power wire from the 7-Way on your trailer is a great way to provide a maintenance charge on your battery to operate a Bulldog jack like part # BD500199. Mounting a battery inside a box like part # 329-HM300BKS inside your trailer will further help to keep your battery safe from the elements (although battery boxes do a pretty good job at that). Please note that the 12V power from your vehicle will not...
    view full answer...

  • Electric Conversion Compatibility for Holland Binkley Model 48000 Series Jack on Horse Trailer
  • The Holland Binkley model 48,000 series jacks are very similar to the Bulldog Square Jack - Drop Leg w/ Spring Return # BD182815 which can utilize the Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity # BD1824200100. Your current jacks are not compatible with the kit to my knowledge so you would need to replace the jacks in order to upgrade to the motor kit. Another option is to use the Bulldog Velocity Series Electric Landing Gear Jack - 24" Lift - 12,000 lbs...
    view full answer...

  • Tripod Stabilizer for Fifth Wheel Pin Box with Andersen Ultimate Connection Adapter
  • The Replacement Ball Assembly # UF19-001057 that you referenced can be used with an Andersen Ultimate fifth wheel adapter but it has to be used with an Ultra Fab stabilizer like the # UF19-950500 since we can't guarantee it would work on an EAZ tripod.
    view full answer...

  • Availability of Wiring Diagram for the Replacement Power Switch # EJ-3520-PSW
  • I am attaching a picture of the Replacement Power Switch # EJ-3520-PSW when it is properly installed on the Electric Jack w/ Footplate # EJ-3520-BBX but unfortunately there isn't a wiring diagram available. If you be mindful to note which position each wire is supposed to be in when you disconnect your current switch you simply just have to install this switch in the same way.
    view full answer...

  • Mounting Hole Spacing of etrailer and Ultra-Fab Scissor Jacks
  • We do have an option for you, but I have added the mounting hole spacing dimensions of the Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 5,000 lbs # TJSCHD-24, and as you can see, none line up exactly with your pre-drilled holes, although it is close, with two of the holes measuring 5-3/16" apart. The jacks that do have the spacing you need are the Ultra-Fab Ultra Scissor Jacks - 24" Lift - 6,500 lbs # UF48-979002, which have the two closest bolt holes at 5" apart as you can see...
    view full answer...

  • Replacement Electric Landing Gear for Horse Trailer
  • Sorry to hear your system broke and there aren't replacement parts available for your horse trailer. The Bulldog Velocity Series Electric Landing Gear Jack - 24" Lift - 12,000 lbs # BD185400 is a good replacement for your discontinued and broken system. It will simply bolt right on to your trailer so it can utilize the 12V power you already have run. It is able to lift 12,000 lbs and lifts 20 inches in 60 seconds. Another great option for you is the Bulldog Square Jack - Drop Leg...
    view full answer...

  • Replacement Motor for Lippert Stabilizer Jack # 337199
  • The replacement motor you need is the # # LC352338 for your Lippert Components Power Stabilizer Jack # LC337199.
    view full answer...

  • Do the Scissor Stabilizer Jacks Come with Install Hardware
  • The Scissor Stabilizer Jacks part # TJSCHD-24-4 do not come with installation hardware. That said, we do offer the self-tapping screws you'll need for this using part # FA1131822. In regards to quantity, you'll need a total of 16.
    view full answer...

  • Replacement for Bent Front Leg of Lippert Ground Control Auto Leveling System
  • Sounds like you have a Lippert Ground Control auto leveling system on your 2016 Highland Ridge Open Range like the # LC358590. For a replacement front leg you'd just need # LC362485 and you'd be set. The price for this is at the attached product links as well. I also attached a review video for this for you to check out too. If you have a different jack setup let me know and I'll see what we can get you set up with.
    view full answer...

  • Replacement Parts for Lippert Electric Stabilizer Jack
  • There are not replacement legs available for the Lippert Components High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift # LC369774 which is the same as the 198641 you mentioned. You will need to replace the entire unit. The support arm # LC1134122 in yellow or # LC1134121 in black is the only non-electric component able to be separately replaced. The motor # LC138445, circuit breaker # LC134181, and switches # LC144214 or # LC387874 as well as switch housing # LC134025 are...
    view full answer...

  • Wiring For Lippert Components High-Speed Power Stabilizer Jack
  • I assume you are asking about wiring the switch of the Lippert Components High-Speed Power Stabilizer Jack # LC369774. For this, please refer to the accompanying cutout I added; your jack uses Switch # LC144214 so as the diagram makes clear, the black wire is retract, the green wire is extend, the white will likely be ground and red will then be power.
    view full answer...

  • Stabilizer Jack Recommendation for Stored Boat Trailer To Support While in Storage
  • Scissor style stabilizer jacks like the Leveling Scissor Jack Set # JSC-24 would be your best option. These were designed to stabilize camper trailers but would work great for what you are wanting. I attached a picture of what they look like in use plus a review video for more info as well.
    view full answer...

  • 2-Motor Powered Landing Gear Recommendation for 2010 Keystone Montana
  • The Montana by Keystone had a special set of landing gear made for them by Lippert. So typically we recommend the part # LC178653 for the lead leg and part # LC178652 for the follow leg. The difference is the mounting bracket location that's on the jack. So your best option for a dual motor landing gear setup would be the Reese kit part # RP500708 which can have the motors inverted when installed like what you see in the attached picture. This will give you more clearance. The mounting...
    view full answer...

  • How to Install the Lippert Components JT's Strong Arm Jack Stabilizer Kit # LC191023 on RV
  • To install the Lippert Components JT's Strong Arm Jack Stabilizer Kit # LC191023 on your hydraulic levels you will need to also install the Lippert Components JT's Strong Arm Jack Stabilizer Adaptor Lug # LC314592. I will be sending the instructions for you to check out in a separate email.
    view full answer...

  • Replacement 500V 30A Fuse for RAM Power Jack
  • We actually carry the replacement fuse part # EJ-FUSE for RAM or etrailer.com trailer jacks, like part # EJ-3520-BBX. With that being said, I have reached out to RAM about this in the past and they have said that there isn't anything special about the fuse so if you are able to find one at your local home improvement store, like one that you mentioned, then it will work just the same.
    view full answer...

  • How to Choose Between the 4-Point and 6-Point Lippert Ground Control 3.0 Leveling System
  • If the gross vehicle weight rating (GVWR) of your trailer is less than 15,500 lbs and the distance between the center of the landing gear foot and center of the rear landing gear jack foot will be less than 20' then you will want to use the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC358590 (4-Point). If the gross vehicle weight rating (GVWR) of your trailer is 15,500 lbs or greater and or the distance between the center of the landing gear foot and center...
    view full answer...

  • Can the Electric Jack w/ Footplate # EJ-3520-BBX be Connected to 12V Circuit on 7-Way
  • You can use the 12V circuit on your 7-Way to power the Electric Jack w/ Footplate # EJ-3520-BBX but it is usually best to use a separate 12V battery that is stored on your trailer. Reason being that sometimes the trailer jack needs more power than the 12V wire from your tow vehicle can deliver. Is it possible, yes, but if that isn't enough power you will need to add a battery to your trailer. We do have the Buyers Products Jack # 3370093500 which you can plug right in to your 7-Way...
    view full answer...

  • Troubleshooting Manual Adjustment Nut for Lippert Electric Trailer Jack
  • The Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black # LC285318 does not yet have a replacement nut available. I reached out to Lippert and they said many people have used impact tools on them instead of the manual handle that comes with it and have damaged that part but they don't yet have a fix for that as it wasn't designed for that use. At this time there is no replacement available, so you would need to replace the entire jack. I've linked the...
    view full answer...

  • Measuring Fit of Fastway ONEstep Wheel Chocks
  • You simply measure between the tires about an inch off the ground to determine what Fastway chocks are the best fit for your application. We have the Fastway ONEstep Wheel Chock for Tandem-Axle Trailers and RVs - 16" to 24" Long # FA84-00-4000 and the Fastway ONEstep XL Wheel Chock for Tandem-Axle Trailers and RVs - 24" to 30" Long # FA84-00-4150. This will actually adjust down to 16 inches if you move the Allen bolts into the different holes according to the manufacturer so if you are...
    view full answer...

  • Comparing Stallion and etrailer.com Drop Leg Stabilizer Jacks for Trailer
  • Quality-wise there isn't much of a difference between the etrailer.com stabilizer jacks part # TJ01RT-HD and the Stallion Stabilizer Jacks # 288-01892-2 that you also mentioned. I'd recommend going with the kit that matches the height requirements you need best. The # 288-01892-2 has a travel of up to 22-1/4 inches and the # TJ01RT-HD has a travel of up to 18 inches. I also attached a review video for these jacks for you to check out as well.
    view full answer...

  • Will Stormberg Carlson Electric Jack JET-5000NG Fit with Lippert Jack It Bike Rack Adapter
  • The Stromberg Carlson Electric Trailer Jack part # JET-5000NG will easily fit with the LCI Jack It bike rack adapter part # LC429756 that you referenced. If you check out the picture I attached you can see a Stromberg jack mounted with the Jack It that has same dimensions as this. The jack and Jack It are actually made by same company so they were designed to fit each other basically.
    view full answer...

  • Replacement Foot Needed for a Lippert # 1817941 Electric Jack
  • The Lippert Electric Trailer Jack # LC285318 is the replacement jack for your 1817941 jack and it has a 2" diameter inner tube. This jack uses the Replacement Jack Foot Pad # LC165253 which fits with the 2" diameter inner tube. If your jack has the same inner tube diameter then you want this part number over the part # LC405217 that has a 1-1/2" tube diameter. I have attached a photo with some dimensions listed so you can confirm a fit on your end before purchasing.
    view full answer...

  • Recommended Truck Bed Camper Jacks for a 1996 Northern Lite Camper
  • The only truck bed camper jacks we offer are the Brophy Cable Camper Jacks. As long as the loaded weight of your truck bed camper does not exceed 3,000 lbs then I recommend part # CJ41 for 57" of lift or part # CJ74 for 67" of lift. These jacks will do an excellent job of helping to load and unload your camper into the truck bed. They do not permanently install on the camper which makes for a very clean look and they can also be broken down into three pieces for easy storage.
    view full answer...

  • Replacement Slow Blow Fuse for Ultra-Fab Electric A-Frame Jack 3502 Model
  • The correct replacement slow blow fuse for the Ultra-Fab Electric A-Frame Jack (3502 Model) part # UF38-944017 is the Replacement 30-Amp Slow Blow Fuse part # UF38-751034. Some other parts you may want to keep on hand are the Replacement 20-Amp Auto-Reset Circuit Breaker part # UF38-101238 and the Replacement Toggle Motor Switch part # UF38-75-1037.
    view full answer...

  • Replacement Jack for Lippert Electric Ground Control TT Travel Trailer Leveling System
  • I believe the leveIing system you have is the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136, based on the model jack you said it had. I spoke with a representative of Lippert who said that Lippert Electric Trailer Jack # LC285318 can be used as a replacement for the damaged jack from the leveling system; additionally, he told me that you would be able to disconnect the wires from the original jack and re-wire them onto the same location of the...
    view full answer...

  • Troubleshooting Electric Trailer Jack with 7-Way Plug That Does Not Function Consistently
  • An electric A-frame tongue jack like # EJ-3527-BBX or # 3370093500 that has a pre-wired 7-way plug will rely on the ground and +12V contacts within that plug to deliver operating power. Jacks may not function with less than 12 volts. Those contacts are located, respectively, at the 5:00 and 11:00 positions on the plug as you look at it. Please refer to the linked photo. You might try an aerosol electrical contact cleaner like Caig De-Oxit to see if that restores reliable operation. I...
    view full answer...

  • What Are The Quietest A-Frame Electric Trailer Jacks
  • There are a number of quiet electric A-frame trailer jacks, although the Stromberg Carlson Electric Trailer Jack # JET-5000 you asked about would not be on the list. That said, you were right on the money with the Bulldog, because their Bulldog Powered Drive Trailer Jack - 22" Lift - 4,000 lbs # BD500199 (Black) or # BD500200 (White) has a powered drive which is going to reduce noise. The other quietest A-frame trailer jack is from Stromberg Carlson, the Stromberg Carlson Electric Trailer...
    view full answer...

  • How to Replace Power Switch on RAM Electric Jack w/ Footplate
  • It sounds like you have either the Electric Jack w/ Footplate part # EJ-3520-BBX or the Electric Jack w/ Footplate part # EJ-3520-WBX. If that is the case then the Replacement Power Switch part # EJ-3520-PSW is the correct replacement for you. In order to replace the switch you need to take a flathead screwdriver or pick and pry the top and bottom of the switch to release it from the housing. You can then unplug the spade connectors from the old switch and into the new switch making sure...
    view full answer...

  • Trouble Uncoupling Trailer From Tow Vehicle
  • Generally speaking, most people will uncouple the trailer before they extend the stabilizer jacks so that is what I recommend first. That said, if you are having trouble getting the trailer high enough to release the hitch ball from the coupler then you would just need to use a stand of some sort like the Valterra Trailer Jack Stand part # A10-0900 which offers another 8" or so of lift. If the trailer lifts the hitch ball on the vehicle when you raise it then you may need to jump up...
    view full answer...

  • Electric Landing Gear Set Needed for Holland Trailer
  • It looks like you have a landing gear set that is similar to the Bulldog 2-Speed Tandem Landing Gear Set # BD500154. I do have a solution for you to have an electric landing gear set but unfortunately we don't have a kit that will fit your landing gear. Instead you will need to replace your current landing gear like the Bulldog 2-Speed Jack # BD183416 and # BD182415. To convert these to electric you then simply need to add the Bulldog Powered-Drive Kit # BD1824180100. These have a weld-on...
    view full answer...

  • Repair Parts for Venture VMC940RB 5th Wheel Landing Gear
  • In case you want to just service your existing Venture VMC940 5th wheel landing gear driver leg you can use gearbox # LG-179015. For a complete replacement lead jack use Replacement Lead Jack with Drop Leg # LG-179013 which is a universal fit that works with major brands. I linked a diagram with measurements so you can compare to yours. For a motor to convert the gearbox and leg to electric operation you can use part # LG-196308.
    view full answer...

  • Out of Stroke Error on Lippert Ground Control
  • I am a bit confused by your question as Kwikee does not make trailer jacks but rather trailer steps. If you were instead referring to trailer jacks such as the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC358590 then the "out of stroke" error means you have extended the jack too far. If the jack will not retract using the touchpad then you will need to do so manually with the manual override on top or bottom (see photo). If you continue to get an "out of...
    view full answer...

  • Replacement Pins for Lippert Ground Control 3.0 Stabilizing System
  • The only replacement pins available for your Lippert Ground Control 3.0 # LC358590 are the Replacement 3/8" x 3" Snapper Pins # LC225598, which are used to attach the foot pad to the jack.
    view full answer...

  • Rear Electric stabilizer for 2016 Winnebago View 24J Sprinter Class C Motorhome
  • Your photo did not come through but we can still help you determine if the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941707 is suitable for use on your Class C Winnebago View 24J motorhome. This stabilizer fits frames from 42- to 77-inches wide and on each side of the frame the mounting brackets will need 24-inches of frame access to mount. Please refer to the linked photo that shows a mounting bracket. If your frame width and available space meet these criteria then this unit...
    view full answer...

  • Replacement Manual Jack Handle for RAM Electric A-Frame Jack
  • The correct replacement manual crank handle for the RAM Electric 3,500 Lb Jack part # EJ-3520-BBX is the Replacement Manual Jack Handle for RAM Electric A-Frame Jacks part # EJ-3520-HD.
    view full answer...

  • Troubleshooting Ram 3,500 lb Trailer Tongue Jack Working Intermittently
  • I reached out to my contact at Ram and he said that their electric jacks, like part # EJ-3520-BBX, # EJ-3520-WBX, or # EJ-3527-BBX have one fuse and it is located on the black wire where it enters the housing. From what you described I believe your problem is a bad ground. These jacks ground through the mounting hardware so if the connection isn't solid and constant it can cause the issues you are having. What my contact recommended doing was taking some of the paint off of the trailer...
    view full answer...

  • Heavy-Duty Scissor Jacks for 15,000 lb Tiny Home
  • We have scissor jacks that will work for you, just keep in mind that scissor jacks are only designed to stabilize a portion of your weight as opposed to the full 15,000 lbs. The scissor jacks with the largest capacity are the Ultra-Fab Ultra Scissor Jacks # UF48-979002 (24" lift) and # UF48-979031 (30" lift). These jacks have a 6,500 lb per jack capacity so the pair will have a total support capacity of 13,000 lbs. So long as part of the weight is spread out on your tiny home these jacks...
    view full answer...

  • How to Replace the Switch on the Lippert Electric Trailer Jack with Footplate Part # LC285318
  • If you are referring to the Lippert Electric Trailer Jack with Footplate part # LC285318 then you are going to want to use the Replacement Extend / Retract Switch Assembly part # LC226023. In order to replace the switch you will need to obtain a pick tool or very small flathead screwdriver and beging to pry the top or bottom of the switch out of the housing. Once this is done you can then remove the spade terminals and install them on the new switch. In order to install the new switch you...
    view full answer...

  • JT Strong Arm Stabilizer Kit & Adapter for Rockwood Travel Trailer with Lippert Electric Stabilizer
  • For your 2018 Rockwood travel trailer with a Lippert electric stabilizer, all you need in order to use the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers # LC191025 is the Electric Stabilizer Jack Pad Adapter # LC314597. I have added a photo a customer sent in so you can see how this adapter would work when using the stabilizer kit on your travel trailer. The adapter kit simply attaches the feet of your stabilizer to the Strong Arm kit and you'll have the added stability you...
    view full answer...

  • Best Way to Stabilize a 40 Foot Travel Trailer
  • For your 40 foot travel trailer, I recommend using four stabilizer jacks and two wheel stabilizers. The stabilizers jacks will need to be placed in all four corner of the trailer and for this, I recommend the Ultra-Fab Ultra Scissor Jacks part # UF48-979031 which have a 6,500 lb capacity and offer up to 30" of lift. If you have a cordless 1/4" impact you can use the speed socket part # UF48-979005 to raise/lower the jacks but if not there is a manual crank handle included. For the wheel...
    view full answer...

  • How to Determine Correct Electric A-Frame Jack for Travel Trailer
  • The correct jack will have a capacity that will surpass your trailer's loaded tongue weight, which is typically between 10 and 15 percent of the loaded trailer's weight. I looked up your 2013 Jayco Jay Feather Ultra Lite Travel Trailer and from my research it looks like your Jayco has a 4,750 lb GVWR so any one of our A-frame jacks would work in terms of weight capacity. The Electric Jack w/ Footplate # EJ-3520-WBX could be a great option; it has a 3,500 lb lift capacity, an extended...
    view full answer...

  • Leg Extension for Lippert Electric Trailer Jack # LC285318
  • The Lippert Electric Trailer Jack # LC285318 that you referenced features an inner tube diameter of 2 inches. We do have a nice selection of jack feet that are compatible with this jack. The Husky Brute Super Foot Fold-Up Jack Foot # HT31610 will fit the jack and provides an extension of 7 inches. This is the largest extension we have available for this jack. It also features a spring-loaded cam lever so you can quickly fold the foot down for use or up for travel. For a standard foot...
    view full answer...

  • Wheel Stabilizer for 2016 Freedom Express 321FEDSLE Tandem-Axle Bumper-Pull Travel Trailer
  • For your 2016 Coachman Freedom Express 321FEDSLE tandem-axle bumper pull travel trailer that has 14-inch wheel spacing you can use the Ultra-Fab Super Grip Chock XL Wheel Stabilizers for Tandem-Axle Trailers, part # UF21-001095, which is shown in the linked video.
    view full answer...