Filter Questions and Answers:

reset filter

Expert Answers about Camper Jack


  • Leveling System Compatible with 42 Foot 5th Wheel Trailer
  • The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w/ Touchpad and Remote - 20,000 lbs # LC358590 is designed for trailers where the measurement from the front landing gear to the rear is 20 feet or less. If longer, then the manufacturer recommends the 6 point system # LC675817 which adds two middle legs. They always navigate to the safe side, because they rate the 4 point system as 20k capacity based on each individual jack rated for 5K capacity. We do not carry...
    view full answer...

  • Dimensions of Reese and Ultra-Fab Fifth Wheel Landing Gear
  • I would be happy to help you with those dimensions. The Reese Electric 5th Wheel Landing Gear # RP500708 has the standard weld stop measurements that are 15-1/2" from inside to inside of weld stops and 17-1/2" from outside to outside. The Ultra-Fab # UF17-943010 has weld stop brackets which measure 20-1/4" from outside to outside; it is 8-1/2" from the top of the motor to the first weld point. I have added photos showing the dimensions of these jacks for you to check out. Apart...
    view full answer...

  • Replacement Control Panel for Leveling System on 1995 Fleetwood Motorhome
  • We had another customer with a '94 Bounder in need of the same control panel for their Lippert Power Gear leveling system and Lippert was able to confirm that kit # LC359259 would work. I shared your photo with my tech contact there and he confirmed the item referenced above will work for you.
    view full answer...

  • Dimensions of I Beam Bracket for Lippert Ground Control Leveling System
  • I attached a dimension picture I got from Lippert for the Replacement I-Beam Jack Bracket # LC349975 that you referenced.
    view full answer...

  • How to Determine Middle Jack Placement of Lippert Ground Control 3.0
  • I spoke with a representative of Lippert concerning the installation of the middle jacks on your Lippert Ground Control 3.0 - 6-Point Set # LC675817 and was told that there is not a set distance. What you will need to do is run a string line like in the directions (see accompanying photo) and the middle jacks when retracted must be above that line. So depending on the measurement of that string it might be possible for you to mount the middle jacks 48 inches forward. I also asked about...
    view full answer...

  • Can Replacement Lippert Components Power Stabilizer Jack LC337199 Be Installed Using Current Wiring
  • Since the Lippert Components Power Stabilizer Jack # LC337199 is a direct replacement for your 337199 Lippert Jack it will be compatible with your current wiring. If you end up needing a new switch and breaker then you will need part # LC387874 for the switch and part # LC134181 for the 6 amp Auto Breaker.
    view full answer...

  • Differences Between the Lippert Components Power Stabilizer Trailer Jacks
  • You made a great choice in the Lippert Components Power Stabilizer Trailer Jack. For starters, all of the jacks measure to be 70-1/2" long with a 3,500 lb weight capacity and have a 30" lift. The difference between them is in regards to what is included with them. The part # LC337199 doesn't come with a switch and part # LC298707 comes with a black switch. That is the only difference.
    view full answer...

  • Determining Correct Lippert Ground Control System for 2006 Heartland Bighorn 5th Wheel Trailer
  • Installing the Lippert Ground Control System on your 2006 Heartland Bighorn 5th Wheel Trailer is a great idea. When determining whether to use the 4-Point Set # LC358590 or the 6-Point Set # LC675817 there are a couple things you will want to look at specific to your Bighorn Trailer. First is the GVWR of the trailer, which is the most it can weigh when fully loaded. If the GVWR is more than 15,500 pounds, then you will want to go with the 6-Point System. If it is less than 15,500 pounds,...
    view full answer...

  • Replacement Stabilizer Jack for the Lippert 198641 Stabilizer Jack
  • The Lippert Components Power Stabilizer Trailer Jack # LC298707 that you referenced will work as a replacement for your 198641 stabilizer jack. If you use the Linc Analog Remote # LC292614 for your RV then this is compatible with that as well. The part # LC298707 comes with a switch, but if you don't need the switch then you can use part # LC337199 instead. It is the same jack, it just doesn't come with the switch.
    view full answer...

  • Replacement Motor for Lippert High-Speed Power Stabilizer Jack
  • To replace the motor on your Lippert High-Speed Power Stabilizer Jack # LC337199, you will just need the Lippert Stabilizer Jack Motor # LC352338. This is a direct replacement on your stabilizer jack and it will install just like the existing unit on the system.
    view full answer...

  • Wiring Electric Jack to Plug Into 7-Way on Tow Vehicle
  • Although wiring an electric jack like the etrailer.com # EJ-3520-BBX you referenced to a dedicated battery on the trailer is the preferred solution for ensuring you get the needed power, you can indeed wire it to a 7-Way plug like # A7WCB for it to be connected to the 7-Way on your truck when needed. If you don't yet have an electric jack, we actually have a 3,500 pound unit available with the Buyers Products # 3370093500 that is designed to be used this way right out of the box. This...
    view full answer...

  • 4-Point Ground Control or 6-Point Ground Control for 2018 Keystone Cougar 338RLK?
  • I have added a photo of the manual from the Ground Control unit which will explain which of the systems, the 4-Point # LC358590 or 6-Point # LC675817 you need to use. From my research it looks like your 2018 Keystone Cougar 338RLK has a 12,490 lb GVWR so unless the center of the landing gear foot and the center of the rear jack foot is 20 feet or greater it is not recommended to use the 6-Point system.
    view full answer...

  • Can the Jacks on a 2019 Keystone Cougar 34TSB Be Converted To Ground Control Auto Level
  • In order to add the auto leveling feature to your 2019 Keystone Cougar 34TSB you would need to purchase the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System part # LC672136 which is an entire system that comes with jacks, control module, wiring, and hardware. The reason you cannot convert what you have to the Electric Ground Control TT is because the jacks you have are not correct for the kit. The jacks you have on your trailer are actually not jacks at all...
    view full answer...

  • Best Landing Gear Upgrade Options for 5th Wheel Trailer
  • We do have motors that you can add to your landing gear. For example, the Landing Gear Set # RVLG-8000 can be operated with the manual crank # RVLG-HDL but you can also add the motor # M1230 and switch # LG-145236 for effortless operation on your end. The next upgrade for landing gear is the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. This is rated for up to 12,000 lbs and operates via separate motors so you can easily level your 5th wheel trailer without using blocks like...
    view full answer...

  • Will the Switch be Included With the Lippert Components Power Stabilizer Jack # LC337199
  • The Lippert Components Power Stabilizer Jack, # LC337199, only includes the jack assembly, motor, and wiring coming off the jack's motor. The Lippert Electric Jack Switch with Harness for Lippert Components High Speed Stabilizer Jacks, # LC387874, is the confirmed switch needed to install the electrical components of this Lippert jack. Lippert also recommends wiring 6 Amp Auto Reset Breaker, # LC134181, between the switch and the jack's motor. I have attached a diagram that shows...
    view full answer...

  • Can Wireless Remote be Added to Lippert 3.0 Ground Control Leveling System
  • We do have a replacement wireless remote for the Lippert Ground Control 3.0 # LC358590, for that you would want the part # LC358601. Here is how the remote would get programmed: 1. Enter the Leveler app on the LINC Remote. 2. Turn the remote on by pressing and releasing the large silver button at the bottom of the unit. 3. Press the “OK” button on the touch screen to access the Function Menu. 4. Press the Leveler App button. 5. With the interface turned off, press LEFT 5 times...
    view full answer...

  • Replacement Parts for Lippert Electric Stabilizer Jack
  • There are not replacement legs available for the Lippert Components High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift # LC369774 which is the same as the 198641 you mentioned. You will need to replace the entire unit. The support arm # LC1134122 in yellow or # LC1134121 in black is the only non-electric component able to be separately replaced. The motor # LC138445, circuit breaker # LC134181, and switches # LC144214 or # LC387874 as well as switch housing # LC134025 are...
    view full answer...

  • Replacement Follow Landing Gear Leg for 1998 Fleetwood Savanna 5th Wheel
  • I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the bevel gear inside your jack leg is the only one that is damaged then you can just obtain the Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060. However, if you don't want to mess with repairing your old jack leg or...
    view full answer...

  • Recommended Replacement Landing Jack System for 2008 Keystone Montana Mountaineer 345DBQ
  • For your 2008 Keystone Montana Mountaneer 345DBQ, the Lippert Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear # LC178653 and follow leg # LC178652 are a perfect replacement. These parts are exactly what you need for your trailer. If you want the entire replacement kit, you can use the Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs # LC333966 or electric # LC333964 which will have only one option of weld stops for your trailer. I've...
    view full answer...

  • Can a Breakaway Battery be Used to Power an Electric A-Frame Trailer Jack
  • If your breakaway system is powered by its own battery then it is likely a 5 amp hour battery which is not high enough to power an electric trailer jack, such as # BD500199, since they can draw about 30 amps under load. The other issue is that a breakaway system needs its own dedicated battery and should not be shared by other 12 volt accessories. If your trailer has a 7-Way trailer connector with functioning 12 volt circuit you could use electric jack # 3370093500 which plugs into a...
    view full answer...

  • Manual Jacks to Lift a 2008 Bronco Polarino Truck Bed Camper
  • Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 Item # CJ74 will work great with your 1,600 pound truck bed camper. Just make sure that the 67 inch maximum lift height is enough to get the camper into the truck bed. The brackets that lift the camper are 21-1/2 inches long so when properly placed at the center of gravity on the camper it will be balanced. It is recommended to have 2 people when operating the jacks so they lift evenly. For tie downs we have custom...
    view full answer...

  • Recommended Largest Stabilizer Jacks For Jayco Octain Trailer
  • For your Jayco Octain, I recommend the Ultra-Fab Ultra Scissor Jacks - 30" Lift - 6,500 lbs - Qty 2 # UF48-979031. The overall length of the mounting plate is 7-1/4 inches, and the width is 3-1/2 inches. I've attached measurements in the attached photo to assist. If you want an even more stable system, I recommend the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs # UF39-941705 or the manual crank version # UF39-941704. These systems are adjustable...
    view full answer...

  • JTs Strong Arm Stabilizer Recommend for 2019 Keystone Montana 385BR with Ground Control
  • Yes, the JT Strong Arm Stabilizer System # LC191023 will work with your LCI Level Up System. I checked with Lippert and found that you can use the JT's Strong Arm Jack Stabilizer Kit # LC191023 with the adapter lugs # LC314592. For your LCI level up system will need a quantity of 6 adapter lugs, these are sold as a quantity of 2 on our site.
    view full answer...

  • Replacement Jack for Lippert Electric Ground Control TT Travel Trailer Leveling System
  • I believe the leveIing system you have is the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136, based on the model jack you said it had. I spoke with a representative of Lippert who said that Lippert Electric Trailer Jack # LC285318 can be used as a replacement for the damaged jack from the leveling system; additionally, he told me that you would be able to disconnect the wires from the original jack and re-wire them onto the same location of the...
    view full answer...

  • How to Charge a Trailer Battery for Use with a Bulldog Jack
  • What you described is actually the best solution! Connecting your battery to 12V Power wire from the 7-Way on your trailer is a great way to provide a maintenance charge on your battery to operate a Bulldog jack like part # BD500199. Mounting a battery inside a box like part # 329-HM300BKS inside your trailer will further help to keep your battery safe from the elements (although battery boxes do a pretty good job at that). Please note that the 12V power from your vehicle will not...
    view full answer...

  • Recommended Electric A-Frame Trailer Jack for 2011 Open Range Journeyer 340FLR
  • Tongue jacks are often rated higher than the weight of the trailer tongue they will be supporting. For tongue jack to meet your needs, I recommend the etrailer.com Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black # EJ-3520-BBX. This jack will mount to the same location on your trailer tongue A-frame and will give you a drop leg as well as a really nice LED light on a separate switch to help with connecting or disconnecting. If you want what I consider to be the best...
    view full answer...

  • Comparing the Stromberg Carlson Trailer Jacks # JET-5000NG VS JET-5000
  • All-around the Stromberg Carlson Electric Trailer Jack # JET-5000NG is nicer than the # JET-5000. The bearings in the part # JET-5000NG allow it to raise and lower much smoother and quicker, the size of the head is a bit smaller and the lighting is nicer too. For how similar the price is between the two the # JET-5000NG really is the winner.
    view full answer...

  • Replacement Scissor Jack for a 2016 R-Pod 178 Trailer
  • It does appear that your 2016 R-Pod 178 uses the Ram scissor jack, # TJSC-24, so it would be the correct replacement. Should you also ever need a replacement handle it is # TJSC-24-HD.
    view full answer...

  • Replacement Cap for RAM Electric A-Frame Trailer Jack
  • For the replacement cap that will cover the manual override on your Electric A-Frame Jack # EJ-3520-BBX, you will just need the Replacement Cap # EJ-3520-BCP. This will include one cap for your jack.
    view full answer...

  • Recommended Electric Jack For Goose Neck Horse Trailer
  • For an electric jack with the 10,000 lb capacity of your Ram 12000 Series manual jack, I recommend the Electric 5th Wheel Landing Gear Set # RP500708. This kit will give you the 2 independently motorized jacks with drop legs and the switches needed. I've attached a photo giving you the dimensions so you can determine fit. Another option is the Bulldog Velocity Series Electric Landing Gear Jack - 24" Lift - 12,000 lbs # BD185400. This is an external unit that is sealed and maintenance...
    view full answer...

  • Electric A-Frame Jack Recommendation for Jayco Jay Flight Travel Trailer
  • For a Jayco Jay Flight travel trailer that weighs 6100-lbs dry you will want an electric tongue jack rated as high as possible to ensure the jack does not have to work too hard; this will help it provide a longer service life. All of our bolt-on a-frame electric tongue jacks are shown on the linked page. These offer varying amount of lift, from 14- to 25-inches. We offer a great-value option in parts # EJ-3520-BBX (black)and # EJ-3520-WBX (white). This jack has 3500-lb capacity, 25-1/8-inches...
    view full answer...

  • Replacement Landing Gear Recommendation for Salem By Forest River
  • The part # RVLG-8000 is going to work well for you since you said the dimensions are the same. The motor kit for this set is part # M1230 and although it may mount differently it will work. The big thing with these kits is the dimensions matching where the landing gear attaches to the trailer. The standard measurement on landing gear legs is 15-1/2 inches between the tabs that are on the legs of the jack like what you see in the picture I attached.
    view full answer...

  • Dual Motor Landing Gear System For 1995 KZ Sportsmen 2200
  • First things first. . . thank you for your service. I am happy to help you obey the unofficial retirement rules and help you find the proper system. We only have a few to choose from that are dual motor. We have the Electric 5th Wheel Landing Gear Set - 36" Travel # RP500708 and the Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs # UF17-943010. Neither of these options fit the exact dimensions you mentioned on your 1995 KZ Sportsmen 2200 (and I do appreciate the...
    view full answer...

  • Replacement Drop Leg Extension for Lippert Power Jack with Additional Height Needed
  • The Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black # LC285318 has a drop leg available that will give an extra 4-1/2 inches with # LC405217.
    view full answer...

  • Installation of etrailer Landing Gear
  • The Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs # RVLG-8HDL will simply mount to the weld-on brackets by being bolted on. While an online copy of the manual is not available for this specific landing gear, I did cut out a portion of the Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs # LG-183708 so you can take a look. In regards to the brackets you asked about, the Replacement Weld-On 5th Wheel Landing Gear Leg Bracket # LC113511 will work with...
    view full answer...

  • How to Remove Pin in Handle Shaft to Replace Gears on an Older Bulldog Model 12 Square Jack
  • I spoke to my contact at Bulldog who said that the Model 12, 180 Series Bulldog jack that you have is the older version of the the current 10K jacks like part # BD182500. Since you have the older version without the spring that you mentioned seeing in other videos it means that pin you are trying to remove has knurls on it. When it was first installed that pin hole was smooth and the knurls on the pin basically "carved" into that pin hole. To remove it you need to use a punch and quite...
    view full answer...

  • Replacement Lippert Ground Control 3.0 6-Point Control Module
  • For your Lippert Ground Control 3.0 six-point leveling system, I haven't heard of any issues. These systems have been on the market as only a factory option for years and just recently became available for aftermarket use like the 4-point system. I was able to find the replacement control module you are seeking and it is # LC346005. This is the proper replacement for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set # LC675817.
    view full answer...

  • How to Determine Correct Landing Gear for a 2010 Keystone Cougar Fifth Wheel
  • To determine if the Landing Gear # RVLG-8000 will fit your 20110 Keystone Cougar you first need to determine the distance between the weld stops on your current gear. If your weld stops (see attached picture) measure 15-1/2" on the inside and 17-1/2" on the outside then the 8K landing gear will do a great job and fit your Keystone Cougar. Let me know if your weld stops are in different locations and I can help you out. Although a lot of motors can be used in place of another one I...
    view full answer...

  • How to Determine if Lippert High-Speed Power Stabilizer Jack Will Fit Forest River Evo 2550
  • I can tell you exactly what you need to know to find out if the the Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707 will fit your Forest River EVO 2550, though these jacks aren't designed to fit any specific trailer. All you need to do is measure the mounting holes for a stabilizer jack on your trailer, and if they are 68-11/16" from center-hole to center-hole then the Lippert jack will fit! Another option is the Ultra-Fab Power...
    view full answer...

  • Will Strong Arm Jack Stabilizer Kit Work With Hydraulic Auto Leveling System?
  • Yes, the JT's Strong Arm Jack Stabilizer Kit # LC191023 will work with your 2016 Forest River Vengeance with the use of six Strong Arm Jack Stabilizer Adaptor Lugs # LC314592 as long as the front two landing gear legs are at least 58 inches apart. The kit will be beneficial in furthering stabilizing and preventing movement in any RV while at it's destination, and particularly one the size of your Forest River.
    view full answer...

  • 2-Motor Powered Landing Gear Recommendation for 2010 Keystone Montana
  • The Montana by Keystone had a special set of landing gear made for them by Lippert. So typically we recommend the part # LC178653 for the lead leg and part # LC178652 for the follow leg. The difference is the mounting bracket location that's on the jack. So your best option for a dual motor landing gear setup would be the Reese kit part # RP500708 which can have the motors inverted when installed like what you see in the attached picture. This will give you more clearance. The mounting...
    view full answer...

  • Troubleshooting Electric Trailer Jack with 7-Way Plug That Does Not Function Consistently
  • An electric A-frame tongue jack like # EJ-3527-BBX or # 3370093500 that has a pre-wired 7-way plug will rely on the ground and +12V contacts within that plug to deliver operating power. Jacks may not function with less than 12 volts. Those contacts are located, respectively, at the 5:00 and 11:00 positions on the plug as you look at it. Please refer to the linked photo. You might try an aerosol electrical contact cleaner like Caig De-Oxit to see if that restores reliable operation. I...
    view full answer...

  • Comparing Stallion and etrailer.com Drop Leg Stabilizer Jacks for Trailer
  • Quality-wise there isn't much of a difference between the etrailer.com stabilizer jacks part # TJ01RT-HD and the Stallion Stabilizer Jacks # 288-01892-2 that you also mentioned. I'd recommend going with the kit that matches the height requirements you need best. The # 288-01892-2 has a travel of up to 22-1/4 inches and the # TJ01RT-HD has a travel of up to 18 inches. I also attached a review video for these jacks for you to check out as well.
    view full answer...

  • How to Install the Lippert Components JT's Strong Arm Jack Stabilizer Kit # LC191023 on RV
  • To install the Lippert Components JT's Strong Arm Jack Stabilizer Kit # LC191023 on your hydraulic levels you will need to also install the Lippert Components JT's Strong Arm Jack Stabilizer Adaptor Lug # LC314592. I will be sending the instructions for you to check out in a separate email.
    view full answer...

  • Recommended Replacement Landing Gear for 2007 Pilgrim 40 Foot 5th Wheel Trailer
  • On your 2007 Pilgrim 40 foot 5th wheel trailer, I recommend using the Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs # UF17-943010. This landing gear will allow you to adjust independently for easy and quick leveling. The leg will travel 1 inch every 15 seconds and has drop legs for even faster compatibility. I've attached a diagram for you to see the connection points based on the weld stops so you can determine if it will bolt right in or if modifications to your...
    view full answer...

  • Does Lippert Stabilizer Jack LC337199 Work on 2014 Thor Chateau?
  • There is a potential option for a power stabilizer jack for your 2014 Thor Chateau, but Lippert Stabilizer Jack # LC337199 has very specific mounting hole spacing of 68-11/16" and is better used as a replacement for trailers that have these mounting dimensions already. Instead, I recommend the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941705, which is designed for either trailers or RVs that have a frame between 48" and 80". It has dual 12V motors that operate independently of...
    view full answer...

  • Recommended Stabilizer Jacks for 2016 Forest River 2608WS Travel Trailer
  • I can't find the factory stabilization specs online, but I think you are correct in your assumption. To replace these jacks I recommend the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs # UF39-941705. This allows individual side adjustment up to 30 inches of lift. For a manual option, I recommend the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs # UF39-941704. For stability under the slide I recommend the...
    view full answer...

  • Out of Stroke Error on Lippert Ground Control
  • I am a bit confused by your question as Kwikee does not make trailer jacks but rather trailer steps. If you were instead referring to trailer jacks such as the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC358590 then the "out of stroke" error means you have extended the jack too far. If the jack will not retract using the touchpad then you will need to do so manually with the manual override on top or bottom (see photo). If you continue to get an "out of...
    view full answer...

  • Replacement Landing Gear for a Keystone Laredo 5th Wheel Trailer
  • Bulldog Tandem Landing Gear Set # BD500162 is a great option for a manual set to replace the landing gear on your Keystone Laredo. I have linked a video review for you. The handle is not included so use # BD500203 to add the crank handle. For an electric set you could use # RVLG-8HDL and add motor # M1230 and, if you don't already have one, a switch # LC145236.
    view full answer...

  • Is there a Way to Identify 5th Wheel Trailer Landing Gear with No Markings
  • It is possible that there is a part number somewhere that would help identify the landing gear on your trailer. Sometimes there is information on the underside of the caps on the tops of the jacks so that is another place you can check if you haven't already. Many landing gear parts are interchangeable among the different manufacturers but this is not always the case so identifying the manufacture and/or model number is important. Another option is to replace the landing gear with...
    view full answer...

  • Jack for Tire Replacement on Lifted Jeep
  • Our scissor jacks should not be used to lift a car to replace a spare tire as they were not designed for that application. Instead, depending on how far you need to lift, you may be able to use the Powerbuilt Unijack # ALL620470, which can lift up to 4,000 lbs and a range between 8-5/8" and 18-3/8", or Powerbuilt Unijack # ALL620471 which has a lift capacity of 6,000 lbs and a lift range between 11" and 21". After lifting your vehicle the jack locks into place with a safety bar so you would...
    view full answer...

  • Dimension Needed to Determine if Etrailer Landing Gear RVLG-8000 Fits Trailer
  • The etrailer Landing Gear Set, part # RVLG-8000 can be used to replace the landing gear set you have on your trailer most likely. Most landing gears are interchangeable but you can take a quick measurement to make sure this works for you. The weld stops measure 15-1/2 inches inside to inside and 17-1/2 inches outside to outside. For a landing gear with a manual crank included you can order part # RVLG-8HDL. You can add a motor to this landing gear. You would just need part # M1230.
    view full answer...

  • Can the Electric Jack w/ Footplate # EJ-3520-BBX be Connected to 12V Circuit on 7-Way
  • You can use the 12V circuit on your 7-Way to power the Electric Jack w/ Footplate # EJ-3520-BBX but it is usually best to use a separate 12V battery that is stored on your trailer. Reason being that sometimes the trailer jack needs more power than the 12V wire from your tow vehicle can deliver. Is it possible, yes, but if that isn't enough power you will need to add a battery to your trailer. We do have the Buyers Products Jack # 3370093500 which you can plug right in to your 7-Way...
    view full answer...

  • Replacement Foot Needed for a Lippert # 1817941 Electric Jack
  • The Lippert Electric Trailer Jack # LC285318 is the replacement jack for your 1817941 jack and it has a 2" diameter inner tube. This jack uses the Replacement Jack Foot Pad # LC165253 which fits with the 2" diameter inner tube. If your jack has the same inner tube diameter then you want this part number over the part # LC405217 that has a 1-1/2" tube diameter. I have attached a photo with some dimensions listed so you can confirm a fit on your end before purchasing.
    view full answer...

  • Troubleshooting Ram 3,500 lb Trailer Tongue Jack Working Intermittently
  • I reached out to my contact at Ram and he said that their electric jacks, like part # EJ-3520-BBX, # EJ-3520-WBX, or # EJ-3527-BBX have one fuse and it is located on the black wire where it enters the housing. From what you described I believe your problem is a bad ground. These jacks ground through the mounting hardware so if the connection isn't solid and constant it can cause the issues you are having. What my contact recommended doing was taking some of the paint off of the trailer...
    view full answer...

  • Can 6-Point Lippert Ground Control System be Downgraded to 4-Point System
  • To downgrade the 6-Point Set Lippert Ground Control 3.0 # LC675817 on your 2014 Arctic Fox 27-5L you will need to disconnect/remove 2 of the rear jacks and then also swap out your current control module for the part # LC304136 which is used for the 4-Point Set # LC358590. I'm not sure why you would want to downgrade your system but if you choose to the weight capacity will still be sufficient. I did reach out to my contact at Lippert who confirmed all of this and advised against downgrading...
    view full answer...

  • Availability of Replacement Screw for Lippert Ground Control 3.0 Rear Legs
  • I spoke with my contact at Lippert who said that there are no replacement parts for the rear jacks of the Ground Control 3.0 Electric Leveling System # LC358590. You will need to replace the whole leg which might not be a bad idea anyways since you said they installed incorrectly and keep getting damaged. We offer both Left # LC305339 and Right # LC344792 side rear legs for you to choose from.
    view full answer...

  • Recommended Electric Motor Power-Drive Kit for Bulldog 2-Speed Jack with Teardrop Style Gear Box
  • For your Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Traditional - 12-1/2" Lift - 10,000 lbs # BD183902 on your 42 foot long gooseneck, the Bulldog Powered-Drive Kit for OEM 2-Speed Planetary Jacks w/ 12,000-lb Capacity # BD1824180100 is not the correct fit for your application. This kit is only for the planetary gear jacks that have the 4 inch square gearbox. For your jacks with the more teardrop style gear box, I reached out to my contact at Bulldog and confirmed the Bulldog...
    view full answer...

  • Replacement Foot Pads for Lippert Ground Control 3.0
  • The replacement foot pads for the Lippert Ground Control 3.0 # LC675817 (6-Point Set) or # LC358590 (4-Point Set) are different; the Replacement Rear Foot Pad # LC377962 has a circular receiver tube and the Replacement Front Foot Pad # LC362486 has a square receiver tube. Since you have the 6-point system and said you lost the left middle I believe you need the Front Foot Pad # LC362486.
    view full answer...

  • Trailer Jack for 2019 Forest River Micro Lite
  • The electric jack I strongly recommend for your 2019 Forest River Micro Lite 21FBRS is the Phoenix Electric Trailer Jack # UF38-944040 because of its unparalleled performance in regards to speed. This jack will give you 10" of travel in just 18 seconds, making it the sports car equivalent of electric trailer jacks; it has 22-1/2" of total travel and a 4,000 lb lift capacity, which is more than enough for your Forest River. This jack does get wired to a 12 volt power source, as you can see...
    view full answer...

  • Replacement Electric Landing Gear for Horse Trailer
  • Sorry to hear your system broke and there aren't replacement parts available for your horse trailer. The Bulldog Velocity Series Electric Landing Gear Jack - 24" Lift - 12,000 lbs # BD185400 is a good replacement for your discontinued and broken system. It will simply bolt right on to your trailer so it can utilize the 12V power you already have run. It is able to lift 12,000 lbs and lifts 20 inches in 60 seconds. Another great option for you is the Bulldog Square Jack - Drop Leg...
    view full answer...

  • How to Replace the Switch on the Lippert Electric Trailer Jack with Footplate Part # LC285318
  • If you are referring to the Lippert Electric Trailer Jack with Footplate part # LC285318 then you are going to want to use the Replacement Extend / Retract Switch Assembly part # LC226023. In order to replace the switch you will need to obtain a pick tool or very small flathead screwdriver and beging to pry the top or bottom of the switch out of the housing. Once this is done you can then remove the spade terminals and install them on the new switch. In order to install the new switch you...
    view full answer...

  • Is Lippert Ground Control 2.0 System Compatible with 3.0 Motor and Leg?
  • The Lippert 2.0 system is not compatible with the motors on the 3.0 system. The 3.0 system uses electric motors that utilize the hall effect where the 2.0 system does not. This is a completely different design which makes the motor and legs incompatible with the controller and wiring of the 2.0 system. You will need to upgrade your system if you desire that style as your system has been replaced. For the 2.0 system we have the Replacement Heavy-Duty Landing Gear Jack Leg for Ground...
    view full answer...

  • Installation of JT Strong Arm Stabilizer Kit for Electric Stabilizer Jacks on Camping Trailer
  • The JT's Strong Arm Jack Stabilizer Kit for Travel Trailers # LC191025 can be used with the Electric Stabilizer Jack Pad Adapter for JT's Strong Arm Jack Stabilizer Kits - Qty 4 # LC314597 and each kit will work on two stabilizer jacks. I've attached a picture to further assist. For your 4 jacks, you will need 2 kits.
    view full answer...

  • Lippert Power Tongue Trailer Jack Switch Replacement Recommendation
  • For a Lippert Power Tongue Jack the correct replacement switch is the Replacement Extend / Retract Switch Assembly for Lippert Components Power Tongue Jack # LC226023. It's not super uncommon for these to go out over time so most likely this will get your jack working again. Especially since it will raise but not lower and raising would draw more amperage than lowering.
    view full answer...

  • Dual Jack Landing Gear for Gooseneck Trailer Transporting Large Water Tank
  • The weight of 1600 gallons of water, without the water tank's own weight factored in, is about 13,350-lbs. For such a high-weight application I suggest Bulldog Square Jacks # BD182804 and # BD182805 along with Connecting Rod # BDCS730300. Two jacks are definitely the way to go. If you wish to motorize this jack setup you can also add motor kit # BD1824200100. I also recommend you first determine the actual pin weight of the loaded trailer so that you can be sure to select jacks with...
    view full answer...

  • Adding Stabilization Jacks To Fifth Wheel Trailer That Uses Lippert 3.0 Ground Control
  • Yes, you can add two stabilizer jacks to the long tail portion of your Sabra to help stabilize it along with your Lippert Ground Control part # LC675817. I recommend the pair of 2 Ultra-Fab Scissor Jacks part # UF48-979031 to add to the rear of the trailer. You probably do not have holes in the trailer frame at the rear of your trailer so you will most likely need to drill into the support brace of the trailer frame to attach the brackets of the jacks. I have attached an installation...
    view full answer...

  • JT Strong Arm Stabilizer Kit & Adapter for Rockwood Travel Trailer with Lippert Electric Stabilizer
  • For your 2018 Rockwood travel trailer with a Lippert electric stabilizer, all you need in order to use the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers # LC191025 is the Electric Stabilizer Jack Pad Adapter # LC314597. I have added a photo a customer sent in so you can see how this adapter would work when using the stabilizer kit on your travel trailer. The adapter kit simply attaches the feet of your stabilizer to the Strong Arm kit and you'll have the added stability you...
    view full answer...

  • Recommended Truck Bed Camper Jacks for a 1996 Northern Lite Camper
  • The only truck bed camper jacks we offer are the Brophy Cable Camper Jacks. As long as the loaded weight of your truck bed camper does not exceed 3,000 lbs then I recommend part # CJ41 for 57" of lift or part # CJ74 for 67" of lift. These jacks will do an excellent job of helping to load and unload your camper into the truck bed. They do not permanently install on the camper which makes for a very clean look and they can also be broken down into three pieces for easy storage.
    view full answer...

  • Drop Leg Extension for Lippert Components Power Tongue Jack LC285318
  • There is a drop leg made specifically for Lippert power jacks such as # LC285318. It is # LC405217.
    view full answer...

  • Electric Tongue Jack for Straight Pole Tongue Recommendation
  • The only electric power jack we have for the pole tongue is the Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs # F141401. This jack will allow up to 22 inches of lift using the 8 inch drop leg and 14 inches of screw travel and will fit 3 to 5 inch tall frames. The only way to use a caster wheel on this jack is to remove the drop leg and use a caster wheel like the Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks # PS1400750340. The...
    view full answer...

  • How to Determine Correct Electric A-Frame Jack for Travel Trailer
  • The correct jack will have a capacity that will surpass your trailer's loaded tongue weight, which is typically between 10 and 15 percent of the loaded trailer's weight. I looked up your 2013 Jayco Jay Feather Ultra Lite Travel Trailer and from my research it looks like your Jayco has a 4,750 lb GVWR so any one of our A-frame jacks would work in terms of weight capacity. The Electric Jack w/ Footplate # EJ-3520-WBX could be a great option; it has a 3,500 lb lift capacity, an extended...
    view full answer...

  • How to Choose the Correct Lippert Components JTs Strong Arm Jack Stabilizers for an RV
  • In order to determine the correct Lippert Components JT's Strong Arm Jack Stabilizers you will want to measure from the center for your front jacks on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC358590. If the distance from the center of each front jack is 58" apart or more than you will want to use part # LC191023 but if this same distance is less than 58" apart than you will want to use part # LC191024. Both of the above kits come with everything...
    view full answer...

  • Recommendations for Manual Stabilizer Jack with 22 Inches of Lift
  • There isn't a manual version of the Ultra_Fab Power Twin stabilizer jack with 22 inches of lift but I do have some options for you. You can use Valterra Folding Manual Stabilizer for Trailers and RVs - 14" to 28" Tall - Aluminum Item # 020106 which uses a ratchet strap to raise/lower the legs. It would have to be placed in an easy to reach location though. Another option is to go with scissor jacks such as # UF48-979031. If you do go with these scissor jacks you can add Ultra-Fab...
    view full answer...

  • Adapter Recommendation to Convert Ultra Fab Tripod for Fifth Wheel Hitch to Gooseneck
  • Sounds like you are looking for the part # UF19-001057 which is just the ball assembly of the part # UF19-950400. This is designed to also be used like you mentioned and can convert an Ultra Fab tripod designed for a fifth wheel hitch to fit a gooseneck hitch.
    view full answer...

  • Recommended Replacement Electric Jack for Atwood 10,000 lb Landing Gear
  • Thank you for the photos. Unfortunately there is not a replacement motor for the Atwood jack that you have. I think your best option is to replace the jack and the motor to get a working assembly. I recommend the Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Planetary - 12-1/2" Lift - 10,000 lbs # BD183816 along with the Bulldog Powered-Drive Kit for OEM 2-Speed Planetary Jacks w/ 12,000-lb Capacity # BD1824180100. Another option is to use the more traditional Reese Electric...
    view full answer...

  • Atwood Landing Gear Replacement for 36" Long Landing Gear
  • To replace the Atwood landing gear on your 5th wheel trailer you will need to measure the distance between your weld stops. This is typically 15-1/2" on the inside and 17-1/2" on the outside (see attached photo). We do have replacement options but since Atwood is no longer in the landing gear business you need to replace your whole landing gear set to ensure that the gear ratio and strengths are the same. If your weld stop locations match the picture then I recommend using the 8,000...
    view full answer...

  • Can Power for the Bulldog Powered Drive Trailer Jack Come from the 7-Way Trailer Connector
  • The installation of a 7-way trailer plug like the Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector part # PK12706 on an electric a-frame trailer jack like the Bulldog Powered Drive Trailer Jack part # BD500200 is not something that we have the ability to offer you unfortunately. However, this process will be extremely simple as all you need to do is insert the power wire on the jack into the correct terminal on the 7-way and then tighter down the screw. It should not take more than...
    view full answer...

  • Electric Landing Gear Set Needed for Holland Trailer
  • It looks like you have a landing gear set that is similar to the Bulldog 2-Speed Tandem Landing Gear Set # BD500154. I do have a solution for you to have an electric landing gear set but unfortunately we don't have a kit that will fit your landing gear. Instead you will need to replace your current landing gear like the Bulldog 2-Speed Jack # BD183416 and # BD182415. To convert these to electric you then simply need to add the Bulldog Powered-Drive Kit # BD1824180100. These have a weld-on...
    view full answer...

  • Rear Electric stabilizer for 2016 Winnebago View 24J Sprinter Class C Motorhome
  • Your photo did not come through but we can still help you determine if the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941707 is suitable for use on your Class C Winnebago View 24J motorhome. This stabilizer fits frames from 42- to 77-inches wide and on each side of the frame the mounting brackets will need 24-inches of frame access to mount. Please refer to the linked photo that shows a mounting bracket. If your frame width and available space meet these criteria then this unit...
    view full answer...

  • What Size Battery Should be Used to Power Bulldog Electric A-Frame Trailer Jacks
  • A standard car battery will work to power Bulldog trailer jack # BD500199. The battery will need to have an amp hour rating greater than 30 amps which is the max current draw of most electric A-frame jacks. Other option is to use jack # 3370093500 or # UF38-944037 provided your tow vehicle has a 7-Way trailer connector with functioning 12 volt circuit. Both of these jacks are powered through the 7-Way so no battery is required on the trailer to run the jack. I have linked videos for...
    view full answer...

  • Wiring For Lippert Components High-Speed Power Stabilizer Jack
  • I assume you are asking about wiring the switch of the Lippert Components High-Speed Power Stabilizer Jack # LC369774. For this, please refer to the accompanying cutout I added; your jack uses Switch # LC144214 so as the diagram makes clear, the black wire is retract, the green wire is extend, the white will likely be ground and red will then be power.
    view full answer...

  • Heavy-Duty Scissor Jacks for 15,000 lb Tiny Home
  • We have scissor jacks that will work for you, just keep in mind that scissor jacks are only designed to stabilize a portion of your weight as opposed to the full 15,000 lbs. The scissor jacks with the largest capacity are the Ultra-Fab Ultra Scissor Jacks # UF48-979002 (24" lift) and # UF48-979031 (30" lift). These jacks have a 6,500 lb per jack capacity so the pair will have a total support capacity of 13,000 lbs. So long as part of the weight is spread out on your tiny home these jacks...
    view full answer...

  • Trailer Jack Stand Rated for Trailers Over 5,000 Pounds
  • Valterra makes the similar jack stand # A10-0900. This one is rated for 10,000 pounds. I have linked a video review of this stand for you.
    view full answer...

  • Troubleshooting Husky Powered A-Frame Jack that Only Lights Work On
  • Sounds like a switch is bad on the Husky jack. For a replacement for that we have the part # HT87452. Also, the power supply feeding the jack may not be sufficient for the load to raise and lower the jack; the 12v feed on a vehicle 7-way may not be delivering amount of current the jack needs. A power jack often needs a dedicated trailer-mounted battery to get the required lifting power. If you do have a dedicated battery, check and make sure you have a good ground at the jack mount...
    view full answer...

  • Does Electric Ground Control TT Level Trailer on Uneven Ground
  • The Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136 does not require your trailer to be on perfectly even ground to level it. That said a 12 inch drop from one side to the other would not allow the jacks to level your trailer because the rear jacks have a maximum of 12 inches of travel while the A-frame jack has 18 inches of travel. Trying to level at an angle which is too steep would get you an "Excessive Angle" error message. This system is designed...
    view full answer...

  • Error on Display After Jack Removed from Lippert Ground Control Leveling System
  • The issue you are having with the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC675817 is an easy fix and you can do it yourself without taking the trailer in anywhere. The system needs rehomed which can be done by following the steps below. 1. Introduce an error - disconnect one of the hall effect sensor wires at the controller. 2. Attempt to operate the jack that is associated with the sensor wire that was disconnected. The touch pad screen will display...
    view full answer...

  • Can Lippert Ground Control Stabilizer Jack be Used on Bumper Pull Trailer
  • Lippert Ground Control # LC358590 is designed for 5th wheel trailers so it is not a good option for your bumper pull trailer. There isn't an automated system like this for travel trailers at this time from us.
    view full answer...

  • Replacement Landing Gear for 2010 Keystone Fuzion FZ322 Fifth Wheel Trailer
  • There is a way for you to determine the correct replacement landing gear for your 2010 Keystone Fuzion, though we do not have landing gear made specifically for your trailer. Instead, you will need to measure the mounting brackets on your trailer from outside to outside like in the attached diagram and choose the amount of lift and weight capacity that will work for you. For example, you may be able to use the Landing Gear # RVLG-8HDL, which has an 8,000 lb capacity, offers 20-1/2" of...
    view full answer...

  • How to Choose Between the 4-Point and 6-Point Lippert Ground Control 3.0 Leveling System
  • If the gross vehicle weight rating (GVWR) of your trailer is less than 15,500 lbs and the distance between the center of the landing gear foot and center of the rear landing gear jack foot will be less than 20' then you will want to use the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC358590 (4-Point). If the gross vehicle weight rating (GVWR) of your trailer is 15,500 lbs or greater and or the distance between the center of the landing gear foot and center...
    view full answer...

  • Measuring Fit of Fastway ONEstep Wheel Chocks
  • You simply measure between the tires about an inch off the ground to determine what Fastway chocks are the best fit for your application. We have the Fastway ONEstep Wheel Chock for Tandem-Axle Trailers and RVs - 16" to 24" Long # FA84-00-4000 and the Fastway ONEstep XL Wheel Chock for Tandem-Axle Trailers and RVs - 24" to 30" Long # FA84-00-4150. This will actually adjust down to 16 inches if you move the Allen bolts into the different holes according to the manufacturer so if you are...
    view full answer...

  • How to Wire the Toggle Switches on the Lippert Electric Trailer Jack LC285318
  • I spoke to my contact at Lippert about wiring the toggle switches for the Lippert Electric Trailer Jack with Footplate part # LC285318. They stated that they don't have any schematics on this unfortunately but what we were able to do is snap a photo of the back of the switch panel. Let me know if this helps. If needed, we have the correct replacement switches as well as the light. The on/off switch is part # LC226018, the extend/retract switch is part # LC226023, and the light board...
    view full answer...

  • Replacement Legs for Lippert Electric Landing Gear Set
  • To replace the legs on your Lippert Electric Landing Gear Set # LC333964, you will just need the Replacement Part # LC179013 for the Lead Leg and # LC179014 for the Follow Leg. I have attached a short video demonstration on these replacement parts for you to check out.
    view full answer...

  • Electric Conversion Compatibility for Holland Binkley Model 48000 Series Jack on Horse Trailer
  • The Holland Binkley model 48,000 series jacks are very similar to the Bulldog Square Jack - Drop Leg w/ Spring Return # BD182815 which can utilize the Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity # BD1824200100. Your current jacks are not compatible with the kit to my knowledge so you would need to replace the jacks in order to upgrade to the motor kit. Another option is to use the Bulldog Velocity Series Electric Landing Gear Jack - 24" Lift - 12,000 lbs...
    view full answer...

  • How Should Replacement Extend/Retract Switch of Lippert A-Frame Jack LC285318 Wire In
  • The replacement extend/retract switch for the Lippert powered A-frame jack part # LC285318 that you referenced is the part # LC226023. I reached out to a representative of Lippert, who explained that while there was no wiring diagram available, when installing the Replacement Extend / Retract Switch Assembly # LC226023 in your Lippert Electric Trailer Jack # LC285318, it will wire up exactly the same as the original, so what you can do before removing the original switch is take a photo...
    view full answer...

  • Troubleshooting Switches Not Working Properly for Lippert Electric Trailer Jack
  • When you say the unit stays on are you talking about the lights for the Lippert Electric Trailer Jack # LC285318 or the actual motor that extends/retracts the leg? If the lights continue to stay on then it would be worth double checking the connections to make sure they look good before replacing the switch with part # LC226018. When it comes to the retract/extend functions being switched it may just mean that you need to swap some wiring on the back. It sounds a little odd that just...
    view full answer...

  • Can Ultra Fab Tripod Stabilizer be Used with Andersen Ultimate Connection Adapter
  • The Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer - Steel - 31" to 54" - 5,000 lbs # UF19-950500 will not fit with the attachment for your Andersen Ultimate in place. However, if you want to keep that hitch attachment in place, you can use the Replacement Gooseneck Tripod Ball Assembly for Ultra-Fab 5th Wheel King Pin Tripod Stabilizer # UF19-001057 to make it work on your system.
    view full answer...

  • Upgrading Discontinued Lippert Trailer Jack 181794
  • The Lippert electric trailer jack 181794 was replaced by the Lippert trailer jack part # LC285318 with a 3,500 lbs capacity and 18 inches of lift. The Lippert jack measures 21-1/2 inches from the bottom of the mounting bracket to the very top of the jack and 10-3/4" from the foot plate to the bottom of the mounting bracket. Fully extended it measures 28-3/4 inches. Since you want a jack with a higher capacity, I recommend Ultra-Fab jack part # UF38-944014. The Ultra-Fab Jack gives you...
    view full answer...

  • Difference Between Scissor Stabilizer Jacks for RV
  • A few of our scissor jacks have different weight capacities. For example, the part # UF48-979002 has a 6,500 lb capacity, the part # TJSC-24 has a 2,500 capacity and the # JSC-24-IND has a 5,000 lb capacity.
    view full answer...

  • Are Lippert Stabilizer Jack Motors # LC138445 and # LC352338 The Same
  • While the two motors do look pretty similar they actually are different and are not interchangeable. The part # LC352338 is not as long and has a wider base whereas the part # LC138445 is a bit longer. The wiring comes out in two different places too.
    view full answer...