It looks like based on the photo you attached that the Replacement Foot Plate for Lippert Components (LCI) Power Gear Hydraulic Jack part # LC359344 would be the correct replacement foot pad for your Lippert Power Gear Hydraulic Jacks. view full answer...
Yes, the DeeMaxx Trailer Wheel Lug Nut # DE65GR is strong enough to be used with an RV that has axles with a higher weight capacity. view full answer...
I believe you have the G10-3E model as there is not a G10-3F. In order to replace this until I recommend using the Atwood RV Water Heater part # AT94191. This heater has the same 10 gallon capacity as the tank you have now and will be a perfect replacement for your 2007 Fleetwood RV GearBox Toy Hauler. It can produce up to 13-1/2 gallons of hot water per hour and has an aluminum-clad tank so you do no have to worry about anymore pin hole leaks.
I was able to confirm all of the above info... view full answer...
The install of the LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen # 3441409775PBK consists of cutting the rails to the correct length to match door height, inserting the header into the rails and then using included screws to attach rails to wall on either side of door opening. It installs on the inside of the toy hauler. It shouldn't be an issue with the inflatable patio set you have currently. view full answer...
The brake relay valve should be located just above the rear axle of your 2005 Fleetwood Discovery 39L. In the attached installation video for the Roadmaster BrakeMaster System w BrakeAway for RVs w Air or Air Over Hydraulic Brakes - Proportional # RM-9160 you can see that the valve is mounted to the frame of the motorhome and should look like figure 10 from the manual. view full answer...
I can help you replace the braking assemblies and bearings on your 2005 Fleetwood Gear Box ASV Travel Trailer. You most likely have 12 inch hubs so you need part # AKEBRK-7-SA for the braking assemblies. You want to measure your hub to be sure you have a 12 inch hub.
I am unable to narrow down the bearing numbers from the information you gave me, I would need to know the bearing numbers that are stamped into the bearings themselves. If you are not able to find the bearing numbers you... view full answer...
The correct SnapPad kit for your Replacement Foot Plate # LC359344 is the SnapPad Prime Jack Pads # SP84FR4.
If you need just a single SnapPad then you're looking for part # SP84FR instead. view full answer...
To determine if the Replacement Pad for SnapPad Jack Stand Pad System # SN37FR will work for your motorhome's leveling system you'll need to measure the diameter of the foot pad and take note of its shape. The # SN37FR can fit 8" diameter square foot pads. I recommend measuring each foot pad as some manufacturers will use different sizes and shapes from front to back. If your diameter or shape differs then let me know and I'd be happy to find a compatible fit for you. view full answer...
Thank you for providing the pictures. The Fan-Tastic Vent Replacement Lift Arm for Roof Vents with Flat Lids item # FVK8014-05 replaces the flat roof vent arm on Fan-Tastic Vents. If you have a Domed shape Fan-Tastic vent you will need the Replacement Lift Arm for Fan-Tastic Vent Roof Vents item # FVK8011-05. view full answer...
The JWM62A actually replaced the # JWM60A and we decided to keep the old part number on our site. So if you ordered a # DV1230BL you'd actually get the current updated version JWM62A. view full answer...
The SnapPad Prime Jack Pads # SP84FR4 are specifically designed to fit the Power Gear Leveling Systems w/ 10" Round Concave Jack Feet on your 2014 Fleetwood Bounder 34B.
The Pads # SC99MR Stromberg told you to use will not fit on your Bounder as they are only for 9" round flat feet. view full answer...
The Power Gear Motor 1010000155 has direct replacements of Replacement Motor for Lippert Power Gear Electric Leveling Jack System part # LC386198 or part # LC89CJ. These can actually be used on either side. I reached out to Lippert and they said to replace the motor with the one that looks like the one you have and to pay no attention to the left and right denotations. view full answer...
In order to choose the correct Blue Ox Aftermarket Off-Road Bumper Adapter for an aftermarket bumper you'll need to measure the d-ring shackle thickness and pin diameter. The max thickness is 1". There is then the part # BX88357 for 7/8" diameter pins or the part # BX88358 for 1" diameter pins.
I did some research on the Fab Fours Stubby Bumper and it uses a 7/8" diameter pin. view full answer...
You'll need to do some quick measuring of your backing plate/brake flange to see if you can use the 6,000 lb Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand # 23-105-09.
I have added photos below that I hope will help. One is of a standard 5-bolt brake flange where the bolts are 2-1/8" apart except for the bottom which are 3" apart. The other photo is of is the brake assembly which shows the dimensions of the AL-KO/Hayes 4-bolt flange, where the holes are 3-1/8",... view full answer...
There is a heavier-duty option to replace the Venture M-9000-PK landing gear motor than the 5,000 lb capacity Lippert Venture 5th Wheel RV Landing Gear Motor # LC142178.
While that is the correct fit, if you want a higher rated capacity you can definitely do that with a motor from Lippert that has a 6,500 lb capacity:
- Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor # LC196308
This is the motor only, and since you mentioned gear box, if you need that as well the correct part... view full answer...
The correct replacement for a Power Gear Motor 1010001093 is the Replacement Motor for Lippert Power Gear Electric Leveling Jack System part # LC89CJ. view full answer...
It does sound like a motor and gear box issue, and so long as your steps are from 2006 or newer (there should be a sticker verifying the year on the motor) then we have exactly what you need with a new motor and and gear box/linkage for your 1101422 / 214-1001 motor:
- Replacement Motor for Kwikee Electric RV Steps # LC379147
- Replacement Gear Box and A Linkage for Kwikee Electric RV Steps # LC379160
If your steps are from before 2006 you would need to replace them, so I have added... view full answer...
To replace your Atwood/Dometic G6A-8E water heater I recommend the Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU - 16" x 16" Door Item # FR98SR. It has similar dimensions at 12-5/8L x 12-13/16W x 19-3/16D so you'll need to make slight alterations to your cutout hole to fill in the gap but the performance output of this unit will be worth the work. The on-demand hot water and ability to set the temperature to a specific degree instead of the old fashioned arrow knob... view full answer...
I don't have any way of determining if the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL will work with your 2007 Fleetwood Nitrous Hyperlite TT Toy Hauler or not, unfortunately.
The Replacement Crank Handle # RVLG-HDL is designed to be a replacement for Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-8HDL.
The part where # RVLG-HDL connects to the landing gear is 1/2" while the outer sleeve has a diameter of 3/4".
I recommend... view full answer...
Go To Results